Use and Care Manual

BEHR PREMIUM PLUS ULTRA
®
Interior Semi-Gloss Enamel
No. 3750 Ultra Pure White
®
No. 3752 White
No. 3753 Deep Base
No. 3754 Medium Base
Stain-Blocking Paint & Primer In One
Excellent Durability &
Hide in Fewer Coats
Extra-Durable Paint Film
Stain & Scuff Resistant
Washable, Easy-Clean Finish
Antimicrobial-Mildew
Resistant Finish
Lifetime Warranty*
Low VOC, 100% Acrylic
The extra protective shell, featuring NANOGUARD
®
Technology, offers a
STAYS LOOKING NEW LONGER
®
Finish for excellent durability.
WHERE TO USE
Properly prepared coated and uncoated Interior surfaces. Ideal for
Family Rooms, Living Rooms, Dining Rooms, Bedrooms, Hallways
and Ceilings.
PREPARATION & PRIME
All surfaces should be properly prepared and cleaned. Remove loose
paint, wash off dirt and grease with detergent, rinse and allow to dry.
Remove mildew stains with a mildew stain remover. Scuff sand glossy
surfaces and repair imperfections. Remove all dust with a damp cloth,
allow to dry. Allow new stucco, plaster and masonry to cure for 30 days
before painting. Use BEHR PREMIUM PLUS ULTRA
®
Paint as a primer
for properly prepared uncoated or painted interior surfaces, including
woods that contain tannins (two primer coats required for redwood and
cedar) and heavily stained areas. Lock in stains with BEHR PREMIUM
PLUS ULTRA Paint as a spot primer. For heavy stains, test for stain
bleed-through by applying BEHR PREMIUM PLUS ULTRA Paint to a small
section. If the stain bleeds through, spot prime another coat to the
stained area and test again before topcoating. If bleeding continues,
a longer dry time is needed before topcoating. For drastic color
changes or when applying deep colors denoted with a dagger (†) on the
color chip, apply a tinted primer coat of BEHR PREMIUM PLUS ULTRA
Paint if needed.
APPLICATION
Apply when air and surface temperatures are between 50-90°F
(10-32°C). Stir paint occasionally. Intermix containers of same
product to ensure color and sheen uniformity. Use a high quality
3/8-1/2” nap roller cover, nylon/polyester brush or an airless sprayer
(.015 - .019” spray tip, 60 mesh filter). Do not thin if using a roller or
brush; however, if using a sprayer and thinning is required, thin with
water at a rate of no more than 1/2 pint per gallon. Certain colors may
require additional coats for complete hide. Darker colors may require
additional dry time between coats. Cooler temperatures or higher
humidity may prolong drying time. After 4 weeks, cured paint film may
be cleaned with a mild, non-abrasive liquid detergent. Dry paint film is
mildew resistant. Do not use on floors.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags, contact
your household refuse collection service.
Visit Behr.com for painting tips, expert project advice and the perfect
color coordination with the ColorSmart by BEHR
®
Tool.
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.
©2016 BEHR PROCESS CORPORATION
Santa Ana, CA 92704 U.S.A. • behr.com
V.O.C. (C.O.V.) <50 g/L • REV: 9/16
FOR TINT BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS
1 Hr Dry Time
2 Hr Recoat Time
250-400 Sq. Ft.
Coverage per Gallon
Protect
from Freezing
Soap & Water
Clean-Up
CAUTION! IRRITANT! HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT
IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS
AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and
doors or use other means to ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase fresh air. If properly used, a
respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer
additional protection; obtain professional advice before using. A dust mask does not provide
protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling.
Close container after each use. FIRST AID: If you experience difficulty in breathing, leave
the area to obtain fresh air. If continued difficulty is experienced, get medical assistance
immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes
and get medical attention; for skin, wash thoroughly with soap and water. If swallowed,
get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
WARNING! This product contains chemicals known to the state of California to cause cancer
and birth defects or other reproductive harm.
*LIFETIME LIMITED WARRANTY Behr Process Corporation warrants to the original residential
consumer purchaser the performance of this product as described on this label for so long
as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT
PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE
WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not
to perform as specified upon inspection by our representative during the warranty period,
Behr Process Corporation will, at its option and upon presentation of proof-of-purchase
(the original receipt), either furnish an equivalent amount of new product or refund the original
purchase price of this product to you. This warranty excludes (1) labor and costs of labor
for the application or removal of any product, and (2) any incidental or consequential
damages, whether based on breach of express or implied warranty, negligence, strict
liability or any other legal theory. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to
you. This warranty gives you specific legal rights and you may also have other rights, which
vary from state to state.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).

Summary of content (1 pages)