Use and Care Manual

BEHR ULTRA
®
EXTERIOR FLAT
• Stain-Blocking Paint & Primer
◊
• Excellent Durability & Hide in
Fewer Coats
• Resists Rain Shortly After Application
• Guards Against Damage from
Sunlight & Moisture
• Stain & Dirt Resistant
• Low Temperature Application
• Enhanced Mildew Resistant Finish
• Lifetime Warranty*
• Low VOC, 100% Acrylic
No. 4850 Ultra Pure White
®
No. 4853 Deep Base
No. 4854 Medium Base
1 Hr Dry Time
2 Hr Recoat Time
250-400 Sq. Ft.
Coverage Per Gallon
Soap & Water
Clean-Up
Protect
FOR TINT BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS.
from Freezing
WHERE TO USE
Ideal for Wood,Vinyl, Aluminum, Fiber Cement Siding, Metals, Brick, Masonry,
Stucco, Steel and Fences.
PREPARATION & PRIME
Use on properly prepared and cleaned coated and uncoated exterior
surfaces. Countersink nailheads, fill and sand smooth. Remove rust,
loose or peeling paint. Repair imperfections and sand smooth.
Wash off dirt, grease and chalk with detergent and/or powerwash.
Remove mildew stains with a mildew stain removing product.
Clean and sand new or weathered wood. Scuff sand or degloss
smooth or glossy surfaces. Scuff sand or etch metals. Rinse and
allow to dry. Caulk windows, doors and other openings. Allow new
stucco, plaster and masonry to cure for 30 days before painting.
Use BEHR ULTRA
®
Paint as a primer for repaired or uncoated surfaces,
including woods that contain tannins (two primer coats required for
redwood and cedar) and heavily stained areas. Lock in stains with the
first primer coat; if necessary, apply a second primer coat of BEHR
ULTRA Paint. For drastic color changes or when applying deep colors
denoted with a dagger (†) on the color chip, apply a tinted primer coat
of BEHR ULTRA Paint if needed.
APPLICATION
Apply product on dry substrates when air and surface temperatures
are between 35°-90°F (2°-32°C) and will remain between 35°-90°F
(2°-32°C) for at least 4 hours after applying. Do not paint when rain or heavy
condensation is expected. Stir paint occasionally. Intermix containers
of same product to ensure color and sheen uniformity. On semi-smooth
surfaces, use a high quality 3/8-1/2" nap roller cover, nylon/polyester
brush or an airless sprayer (.015-.021" spray tip, 60 mesh filter). On rough
surfaces, use a high quality 3/4-1" nap roller cover. Do not thin if using a
roller or brush; however, if using a sprayer and thinning is required, thin with
water at a rate of no more than 1/2 pint per gallon. Certain colors
may require additional coats for complete hide. On heavy stains and
woods that contain tannins, allow 12-16 hours of dry time between
coats. Cooler temperatures or higher humidity may prolong drying time. After
4 weeks, cured paint film may be cleaned with a mild, non-abrasive liquid
detergent. Dry paint film is mildew resistant. When applying to
vinyl, color choice must be the same color or lighter than the existing
color. Do not use on floors.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags, contact
your household refuse collection service.
Visit Behr.com for painting tips, expert project advice and the perfect
color coordination with the ColorSmart by BEHR
®
Tool.
WARNING! If you scrape, sand or remove old paint, you may release lead
dust. LEAD IS TOXIC. Contact the National Lead Information Center at
1-800-424-LEAD or log on to www.epa.gov/lead.
*LIFETIME LIMITED WARRANTY Behr Process Corporation warrants to the original residential
consumer purchaser the performance of this product as described on this label for so long
as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT
PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE
WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not
to perform as specified upon inspection by our representative during the warranty period,
Behr Process Corporation will, at its option and upon presentation of proof-of-purchase
(the original receipt), either furnish an equivalent amount of new product or refund the original
purchase price of this product to you. This warranty excludes (1) labor and costs of labor
for the application or removal of any product, and (2) any incidental or consequential
damages, whether based on breach of express or implied warranty, negligence, strict
liability or any other legal theory. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to
you. This warranty gives you specific legal rights and you may also have other rights, which
vary from state to state.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov
©2021 BEHR PROCESS CORPORATION
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. <50 g/L • REV: 5/21
US Patent #7482054
◊
A primer coat may be needed on some surfaces. See preparation and prime for details.
WARNING! CAUSES EYE AND SKIN IRRITATION. MAY CAUSE
RESPIRATORY TRACT IRRITATION. CONTAINS: ETHYLHEXYL
BENZOATE, DIURON, CRYSTALLINE SILICA and TITANIUM DIOXIDE
.
Avoid contact with skin and eyes and avoid breathing vapors, spray mist and sanding dust. Sanding, grinding
or abrading may release sanding dust, which may be harmful if inhaled and has been shown to cause lung
damage or cancer with long term exposure. Do not breathe dusts, vapor, or spray mist. To avoid breathing in
dust, vapors, and spray mist, open windows and doors or use other means to ensure fresh air entry during
application, drying, sanding, and/or abrading. If properly used, a respirator (NIOSH approved with particulate
pre-filter) may offer additional protection and should be used if adequate ventilation cannot
be provided; obtain professional advice before using. If you experience eye watering,
headaches, or dizziness during application or drying, increase fresh air or leave the area. Avoid
contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air.
If continued difficulty is experience, get medical assistance immediately. In case of eye contact,
flush immediately with plenty of water for at least 20 minutes and get medical attention; for
skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.