BEHR ULTRA
EXTERIOR FLAT
* No. 4850 Ultra Pure White
®
No. 4853 Deep Base
*No. 4854 Medium Base
Stain-Blocking Paint & Primer In One
Excellent Durability & Hide
in Fewer Coats
Extra-Protective Shell Guards Against
Damage from Sunlight & Moisture
Stain & Dirt Resistant
Low Temperature Application
Enhanced Mildew Resistant Finish
Lifetime Warranty*
Low VOC, 100% Acrylic
WHERE TO USE
Properly prepared and cleaned coated or uncoated exterior surfaces. Ideal
for Wood,Vinyl, Aluminum, Fiber Cement Siding, Metals, Brick, Masonry,
Stucco, Steel and Fences.
PREPARATION & PRIME
Use on properly prepared and cleaned coated and uncoated exterior
surfaces. Countersink nailheads, fill and sand smooth. Remove rust,
loose or peeling paint. Repair imperfections and sand smooth.
Wash off dirt, grease and chalk with detergent and/or powerwash.
Remove mildew stains with a mildew stain removing product.
Clean and sand new or weathered wood. Scuff sand or degloss
smooth or glossy surfaces. Scuff sand or etch metals. Rinse and
allow to dry. Caulk windows, doors and other openings. Allow new
stucco, plaster and masonry to cure for 30 days before painting.
Use BEHR ULTRA
Paint as a primer for repaired or uncoated surfaces,
including woods that contain tannins (two primer coats required for red-
wood and cedar) and heavily stained areas. Lock in stains with the first
primer coat; if necessary, apply a second primer coat of BEHR ULTRA
Paint. For drastic color changes or when applying deep colors denoted
with a dagger (†) on the color chip, apply a tinted primer coat of
BEHR ULTRA Paint if needed.
APPLICATION
Apply product on dry substrates when air and surface temperatures
are between 35°-90°F (2°-32°C) and will remain between 35°-90°F
(2°-32°C) for at least 4 hours after applying. Do not paint when rain or
heavy condensation is expected. Stir paint occasionally. Intermix containers
of same product to ensure color and sheen uniformity. On semi-smooth
surfaces, use a high quality 3/8-1/2" nap roller cover, nylon/polyester
brush or an airless sprayer (.015-.021" spray tip, 60 mesh filter). On rough
surfaces, use a high quality 3/4-1" nap roller cover. Do not thin if using a
roller or brush; however, if using a sprayer and thinning is required, thin
with water at a rate of no more than 1/2 pint per gallon. Certain colors
may require additional coats for complete hide. On heavy stains and
woods that contain tannins, allow 12-16 hours of dry time between
coats. Cooler temperatures or higher humidity may prolong drying time.
After 4 weeks, cured paint film may be cleaned with a mild, non-abrasive
liquid detergent. Dry paint film is mildew resistant. When applying to
vinyl, color choice must be the same color or lighter than the existing
color. Do not use on floors.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags, contact
your household refuse collection service.
Visit Behr.com for painting tips, expert project advice and the perfect
color coordination with the ColorSmart by BEHR
®
Tool.
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.
WARNING! IRRITANT! HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT
IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS
AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and
doors or use other means to ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase fresh air. If properly used, a
respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer
additional protection; obtain professional advice before using. A dust mask does not provide
protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling.
Close container after each use. FIRST AID: If you experience difficulty in breathing, leave
the area to obtain fresh air. If continued difficulty is experienced, get medical assistance
immediately. In case of eye contact, flush immediately with plenty of water for at least
15 minutes and get medical attention; for skin, wash thoroughly with soap and water.
If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
WARNING! This product contains chemicals known to the state of California to cause cancer
and birth defects or other reproductive harm.
©2019 BEHR PROCESS CORPORATION
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. <50 g/L • REV: 6/19
US Patent #7482054
250-400 Sq.
Ft. Coverage
2 Hr Dry Time
4 Hr Recoat Time
Soap & Water
Clean-Up
Protect
from Freezing
FOR TINT BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS.
*LIFETIME LIMITED WARRANTY Behr Process Corporation warrants to the original residential
consumer purchaser the performance of this product as described on this label for so long
as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT
PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE
WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not
to perform as specified upon inspection by our representative during the warranty period,
Behr Process Corporation will, at its option and upon presentation of proof-of-purchase
(the original receipt), either furnish an equivalent amount of new product or refund the original
purchase price of this product to you. This warranty excludes (1) labor and costs of labor
for the application or removal of any product, and (2) any incidental or consequential
damages, whether based on breach of express or implied warranty, negligence, strict
liability or any other legal theory. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to
you. This warranty gives you specific legal rights and you may also have other rights, which
vary from state to state.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
 
 

Summary of content (1 pages)

Don't see a manual you are looking for?