TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 8/2019
1 of 2
EXTERIOR SEMIGLOSS ENAMEL PAINT
NO. 5850 ULTRA PURE WHITE®
PRODUCT INFORMATION
BEHR ULTRA™ Exterior Semi-Gloss Enamel Paint is a 100% acrylic paint & primer in one. With advanced NANOGUARD® Technology,
this product creates a STAYS LOOKING NEW LONGER® Finish. This extra-protective shell shields against damage from sunlight, moisture,
stains and dirt. It’s the perfect choice for all weather climates, even for application at 35°F (2°C).
RECOMMENDED USES:
Ideal for properly prepared coated and uncoated exterior substrates such as:
• Stucco •Concrete • Masonry • Concrete Masonry Units • Brick
• Fiber Cement • Wood • Engineered Wood • Steel • Galvanized Steel
• Aluminum • Other Ferrous Metals • Other Non-Ferrous Metals • Architectural Plastics
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
Ultra Pure White No. 5850 128 oz / 2 oz
Medium Base No. 5854 120 oz / 10 oz
Deep Base No. 5853 116 oz / 14 oz
Gloss: 45-55 @ 60°
Resin Type: 100% Acrylic
Weight per Gallon: 10.4 lb
% Solids by Volume: 35% ± 2%
% Solids by Weight: 47% ± 2%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 100-110 KU
Recommended Film Thickness:
Wet: 6.4 mils / Dry: 2.2 mils @ 250 sq ft/gal
Wet: 4.0 mils / Dry: 1.4 mils @ 400 sq ft/gal
Coverage: 250-400 sq ft/gal depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" - 1" nap roller cover, depending on
surface texture
Airless Spray:
Tip: .015"- .019"
Filter: 60 mesh
Fluid Pressure: 1,400 - 2,400 psi
Thinning: Do not thin if using a roller or brush; however,
if using a sprayer and thinning is required, thin with water
at a rate of no more than 1/2 pint per gallon.
Dry Time: @ 77°F & 50% RH
To Touch: 2 hours
To Recoat: 4 hours
Full Cure: 4 weeks
Dry times are temperature, humidity, and lm thickness
dependent.
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling paint,
rust and all other foreign substances.
New Wood: Remove mill glaze with sandpaper or use a
product such as BEHR PREMIUM® All-In-One Wood Cleaner
No. 63 to open the pores of the wood and follow all label
instructions. For severe stains caused by mold, mildew, algae
and fungus, apply a mildew stain removing product. Set nails
and ll holes, scratches, and gouges with the appropriate
wood ller and let dry completely. Remove all dust with a
wiping cloth. Fill all gaps with a 100% acrylic, siliconized,
paintable caulking and allow to dry completely. Patched
and lled surfaces should be sanded smooth and dusted
clean prior to coating. WARNING! Sanding or scraping
pressure treated lumber may be hazardous; wear appropriate
protection.
New Masonry: The pH must be 10 or lower prior to
coating. Smooth masonry may require an adequate prole
for adhesion. For all other smooth trowel concrete, create
an adequate prole for adhesion using a product such as
muriatic acid etcher or with mechanical means. Remove all
loose aggregate and debris. Prime the area with an alkali-
resistant primer.
Steel: Minimum surface preparation is Hand Tool Cleaning
in accordance with SSPC-SP2. Remove all oil and grease from
the surface with a solvent in accordance with SSPC-SP1.
For optimal performance, use Commercial Blast Cleaning
in accordance with SSPC-SP6. Prime the area with a rust-
inhibitive primer the same day as cleaned.
Galvanized Steel: Solvent clean new galvanized metal
in accordance with SSPC-SP1 to remove oil and grease from
the surface. Pre-treat with a phosphoric acid solution or
a commercially-available etching solution. Galvanized
metal that has been passivated with chromates or silicates
may require brush blasting in accordance with SSPC-SP16
to remove these treatments. Rusty galvanizing requires a
minimum of Hand Tool Cleaning in accordance with SSPC-SP2.
Prime the area the same day as cleaned.
Shop-Primed Steel: As there is potential for many forms
of contamination during storage and transport, a thorough
cleaning is always recommended for shop-primed surfaces.
Paint exposed areas, i.e., where shop primer is abraded,
with the same material as used for shop priming to comply
with SSPC-PA 1 for touching up shop-primed surfaces. Note:
Assess the integrity of the shop primer prior to application
of subsequent coatings. Review all coatings intended for the
project and conrm the compatibility between shop and
eld-applied coatings.
Aluminum: Remove all oil and grease from the surface with
a solvent in accordance with SSPC-SP1. Prime the area the
same day as cleaned.
Stain-Blocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and
test again before topcoating the entire area. If bleeding
continues, primer may need a longer dry time before
applying topcoat.
Previously Painted Surfaces: Remove all loose and
peeling paint and all other foreign substances. Clean any
dirt and grease by scrubbing the surface with a detergent
and water solution, followed by a thorough rinsing with
clean water. Set nails and ll holes, scratches, and gouges
with the appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth. Fill all gaps with
a 100% acrylic, siliconized, paintable caulking, and allow to
completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the surface
thoroughly to provide a rough surface before coating.
COMPLIES WITH THE BELOW AS OF 8/1/2019
SCAQMD YES LADCO YES
CARB SCM 2007 YES AIM YES
CARB YES MPI# 11
OTC Phase II YES GREENGUARD®
#
YES
OTC YES
#
GREENGUARD is a registered trademark of UL Company.