TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2015 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
*For as long as you reside in your home. See label for details.
Revised 11/2015
2 of 2
Scale: Remove all rust and mill scale using sandpaper,
steel wool, abrasive blasting, or other abrading methods.
Prole: For best adhesion results, sand all metal surfaces
(including new ones) with sandpaper, steel wool, or etch
using a product with muriatic acid. Clean by scrubbing the
surface with a detergent and water solution, followed by a
thorough rinsing with clean water. All ferrous metals must
be primed the same day it is cleaned to prevent rust.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Wood: Composition Panels/Siding, Fiber Board
• BEHR PREMIUM PLUS® Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Wood: Cedar, Redwood, Shakes & Shingles
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Tannin/Stainblocking:
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Masonry: Stucco, Cinder Block, Cut Masonry Unit’s
(CMUs), Split Face Block
• BEHR PREMIUM Basement & Masonry Waterproofer
No. 875 (can also be used as a block ller.)
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Masonry: Cement Composition Panels/Siding,
Exterior Insulation and Finish Systems (EIFS)
or Synthetic Stucco
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875 (can also be used as a block ller.)
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Masonry with pH Levels up to 13.0:
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875
• BEHR PREMIUM PLUS Exterior Multi-Surface Primer
& Sealer No. 436
Ferrous and Non-Ferrous Metal:
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Vinyl Siding, Architectural Plastics:
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
PREVIOUSLY PAINTED SURFACES:
• Use a full coat or spot prime with BEHR PREMIUM PLUS
Interior/Exterior Multi-Surface Primer & Sealer No. 436
TEST SPECIFICATIONS:
Scrubbability:
ASTM D2486 Scrub > 2500 (no shim)
Biological Growth:
ASTM D3273 (4 weeks) – Pass
Accelerated Weathering:
ASTM D4587 - 500 hrs - Pass
Flexibility:
ASTM D4587, 500 hrs exposure - Pass
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers and unused product, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply at temperatures between 35° - 90°F.
Temperatures above 90°F may aect the application such
as drying too fast. Avoid painting in direct sun. NOTE: If the
surface is hot to the touch it should be considered too hot
to apply this coating.
• Avoid heavy trac for 24 hours.
• Allow four weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
EXTERIOR SATIN ENAMEL PAINT
NO. 9050 ULTRA PURE WHITE®