Specification

ManualsBrandsBEHR ULTRA ManualsPaint5 gal. #N500-6 Graphic Charcoal Satin Enamel Exterior Paint and Primer in One

TECHNICAL DATA SHEET

This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other

nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,

Revised 6/2016

1 of 2

EXTERIOR SATIN ENAMEL PAINT

NO. 9850 ULTRA PURE WHITE®

PRODUCT INFORMATION

BEHR PREMIUM PLUS ULTRA® Exterior Satin Enamel Paint is a 100% acrylic latex paint and primer in one. With advanced

NANOGUARD® Technology, this product creates a STAYS LOOKING NEW LONGER® Finish. This extra-protective shell shields

against damage from sunlight, moisture, stains and dirt. It’s the perfect choice for all weather climates, even for

application at 35°F (2°C).

RECOMMENDED USES:

Ideal for use on properly prepared, coated or uncoated, exterior surfaces such as:

• Concrete • Concrete Block/CMU • Cement Board Siding

• Brick • Stucco • Wood

• Plywood • Ferrous Metals • Non-Ferrous Metals

PRODUCT SPECIFICATIONS:

Tint Bases/Max Tint Load:

No. 9850 128 oz. / 2 oz.

No. 9854 120 oz. / 10 oz.

No. 9853 116 oz. / 14 oz.

Gloss: 15-25 @ 60°

Sheen: >35 @ 85°

Resin Type: 100% Acrylic Latex

Weight per Gallon: 10.8 lbs.

% Solids by Volume: 37.1%

% Solids by Weight: 50.4%

VOC: <50 g/L

Flash Point: N/A

Viscosity: 100-110 KU

Recommended Film Thickness:

Wet: 6.4 mils / Dry: 2.4 mils @ 250 Sq. Ft./Gal.

Wet: 4.0 mils / Dry: 1.5 mils @ 400 Sq. Ft./Gal.

Coverage: 250-400 Sq. Ft./Gal. depending on application

method and substrate porosity. Does not include the loss of

material from spraying.

APPLICATION:

Brush: Nylon/polyester

Roller: 3/8" - 1/2" nap

Airless Spray: At packaged consistency

Tip: .015"- .021"

Filter: 60 mesh

Thinning: (If required) No more than 1/2 pint

of water per gallon.

Dry Time: @ 77° & 50% RH

Longer dry time may be required in cooler temperatures

and higher humidity.

To Touch: 2 hours

To Recoat: 4 hours

Full Cure: 4 weeks

SURFACE PREPARATION:

All surfaces must be clean, free of dust, chalk, oil, grease,

wax, polish, mold and mildew stains, loose and peeling

paint, rust and all other foreign substances.

New Wood: Remove mill glaze with sandpaper or use a

product such as BEHR PREMIUM® All-in-One Wood Cleaner

No. 63 to open the pores of the wood and follow all label

instructions. Remove mildew stains with a common mildew

removing product. Set nails and ll holes, scratches,

and gouges with the appropriate wood ller and let dry

completely. Remove all dust with a wiping cloth. Fill all gaps

with a 100% acrylic, siliconized, paintable caulking and allow

to dry completely. Patched and lled surfaces should be

sanded smooth and dusted clean prior to coating.

Non-Ferrous Metal: The oil lm on new non-ferrous metal

must be removed before it is painted. Remove oil lm with a

detergent and water solution. For better paint adhesion, sand

the surface with sandpaper, steel wool, or by using a product

such as a muriatic acid etcher. Clean by scrubbing the surface

with a detergent and water solution, followed by a thorough

rinsing with clean water. Metal: Remove all rust and mill

scale using sandpaper, steel wool, abrasive blasting, or other

abrading methods to create a prole on the metal’s surface.

Clean the metal by scrubbing the surface with a detergent

and water solution, followed by a thorough rinsing with clean

water. Bare metal must be coated the same day it is cleaned.

Vinyl Siding, Architectural Plastics: All surfaces must be

clean, free of dust, chalk, mold and mildew stains, loose and

peeling paint and all other foreign substances. Clean surfaces

with a detergent and water solution by scrubbing the surface

vigorously and rinse with a garden hose or a power washer

and allow drying. CAUTION: Vinyl siding is manufactured

to withstand certain levels of heat intensity. Be sure when

choosing a paint color, to select a color which is similar

or lighter than the vinyl siding’s original color. A darker

color paint will absorb more heat, resulting in a

warping of the siding.

Wood: Shakes & Shingles, Composition Panels/

Siding, Fiber Board: New: Remove mill glaze on smooth

wood with sandpaper or a product such as BEHR PREMIUM

All-in-One Wood Cleaner No. 63. Set nails and ll holes,

scratches, and gouges with the appropriate wood ller and

let dry completely prior to coating. Previously Painted

Wood: Remove all loose and peeling paint and all other

foreignsurface with a detergent and water solution, followed

by a thorough rinsing with clean water. Set nails and ll

holes, scratches, and gouges with the appropriate wood ller

and let dry completely prior to coating. Remove all dust with

a wiping cloth. Fill all gaps with a 100% acrylic, siliconized,

paintable caulking, and allow to completely dry prior to

coating. Glossy Surfaces: For maximum adhesion, sand the

surface thoroughly before coating.

Wood: WARNING! Sanding or scraping pressure treated

lumber may be hazardous; wear appropriate protection.

Tannin Bleed & Stainblocking: After priming, test for

stain bleed-through by applying the topcoat to a small

section. If the stain bleeds through the topcoat, apply a

second coat of primer and test again before top coating

the entire area. If bleeding continues, a longer dry time

of the primer may be needed before topcoating or an

additional coat of primer may be required to block the

tannin bleed or stain.

Weathered Wood Surfaces: To remove loose wood

bers, latex, oil-based and 100% acrylic coatings on new or

weathered wood decks, siding, fences, shakes, and shingles,

use a product such as BEHR PREMIUM Wood Stain & Finish

Stripper No. 64 and follow all label instructions. Use a product

susch as BEHR PREMIUM® All-in-One Wood Cleaner No. 63

COMPLIES WITH THE BELOW AS OF 6/1/16

SCAQMD YES LEED v.4

†

YES

CARB YES MPI#

15, 315

OTC YES GREENGUARD® YES

LADCO YES CHPS YES

AIM YES NAHB/ICC NGBS YES

LEED v.3 (2009)

†

YES

†

Please visit www.usgbc.org/LEED for additional details.

GREENGUARD is a registered trademark of UL Company.

Summary of content (2 pages)

PAGE 1
TECHNIC AL DATA SHEET EXTERIOR SATIN ENAMEL PAINT N O. 9 8 5 0 U LT R A P U R E W H I T E ® PRODUCT INFORMATION COMPLIES WITH THE BELOW AS OF 6/1/16 BEHR PREMIUM PLUS ULTRA® Exterior Satin Enamel Paint is a 100% acrylic latex paint and primer in one. With advanced NANOGUARD® Technology, this product creates a STAYS LOOKING NEW LONGER® Finish. This extra-protective shell shields against damage from sunlight, moisture, stains and dirt.
PAGE 2
TECHNIC AL DATA SHEET EXTERIOR SATIN ENAMEL PAINT N O. 9 8 5 0 U LT R A P U R E W H I T E ® and follow all label instructions to clean and brighten the wood surface and to remove light to medium stains caused by mold, mildew, algae and fungus. Be sure to follow all label instructions. Masonry: Stucco, Concrete, Cut Masonry Unit’s (CMUs), Split-Faced Block: New: All masonry surfaces must be cured at least 30 days before painting. The pH must be 10.0 or lower prior to coating.