TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 2/2017
1 of 1
PRODUCT INFORMATION
BEHR® Solid Color House & Fence Wood Stain creates a durable lm that resists cracking and peeling on your home’s
vertical surfaces. It’s available in more than 1,600 custom and computer-matched colors and is great for most
vertical wood surfaces.
RECOMMENDED USES:
Recommended for smooth or rough sawn exterior vertical wood surfaces such as:
• Wood
• Engineered (Synthetic) Wood
• Pressured Treated Lumber
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 11 Tintable White 124 oz. /4 oz.
No. 30 Deep Base 116 oz. / 12 oz.
Resin Type: Oil-Latex
Weight per Gallon: 9.8 lbs
% Solids by Volume: 35.6%
% Solids by Weight: 44.6%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 70-80 KU
Recommended Film Thickness:
Wet: 8.0 Dry: 3.0 mils @ 200 Sq. Ft./Gal.
Wet: 4.0 Dry: 1.5 mils @ 400 Sq. Ft./Gal.
Coverage: 200-400 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/4" nap
Airless Spray: At packaged consistency
Tip: .015- .019"
Filter: 60 mesh
Dry Time: @ 77° & 50% RH
To Touch: 2-3 hours
To Recoat: 6-8 hours
• Follow spraying immediately with back brushing or back
rolling for a uniform appearance.
• Maintain a wet edge when applying.
SURFACE PREPARATION:
The following steps and products are required: If you
use a product such as BEHR PREMIUM® Wood Stain & Finish
Stripper No. 64 to remove loose wood bers, latex, oil-based
and 100% acrylic coating on new or weathered wood, then
you must use BEHR PREMIUM® All-In-One Wood Cleaner
No. 63 to clean, brighten & neutralize wood. If you do not
use BEHR PREMIUM Wood Stain & Finish Stripper No. 64 as
described above, then use a product such as BEHR PREMIUM
All-In-One Wood Cleaner No. 63 to clean and brighten the
wood surface and to remove light to medium exterior stains
caused by mold, mildew, algae & fungus. Rinse thoroughly
and allow to dry before coating. On new wood, use a product
such as BEHR PREMIUM All-In-One Wood Cleaner No. 63
to remove mill glaze and open the pores of the wood.
Lightly sand to remove remaining wood bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
Wood:
• No primer needed on most woods. However, redwood,
cedar, cypress and other “bleeding” woods contain water
soluble extractives which may cause discoloration of white
and pastel colors. Therefore, prime the above type wood.
For Severe Tannin Bleed/Stainblocking:
• BEHR PREMIUM PLUS® Exterior Multi-Surface Primer &
Sealer No. 436
PREVIOUSLY PAINTED SURFACES:
• Use a full coat or spot prime with BEHR PREMIUM PLUS
Exterior Multi-Surface Primer & Sealer No. 436 on
properly prepared surfaces.
CLEAN UP:
Clean all tools and equipment with clean water. For proper
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing
• Do not use without the addition of tinting colorants
• Do not use if rain is expected within 24 hours
• DO NOT THIN PRODUCT
• Avoid applying stain in direct sunlight or hot surfaces
• Test product for color on a small hidden area before proceeding
• No primer needed on most woods. However, redwood,
cedar, cypress and other “bleeding” woods contain water
soluble extractive which may cause discoloration of white
and pastel colors; therefore prime the above type woods
with one coat of a product such as BEHR PREMIUM PLUS
Exterior Multi-Surface Primer & Sealer No. 436.
• Over application of stain will lead to surface failure
including peeling & cracking
• Shelf life under normal conditions is two years
(unopened containers)
• Temperature Range: 40-90°F (4.5-32°C)
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Harmful if swallowed.
Wear protective clothing, gloves, eye, and face protection.
Do not eat, drink, or smoke when using this product. Take
o contaminated clothing and wash it before reuse. Wash
hands thoroughly after handling. Collect spillage and avoid
release to the environment. Dispose of unused, contents,
container and other contaminated wastes in accordance
with local, state, federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and easy
to do. Continue rinsing and get medical attention if eye
irritation persists. If on skin: Wash with plenty of soap
and water. If swallowed: Rinse mouth and get medical
attention if you feel unwell.
SOLID COLOR HOUSE & FENCE WOOD STAIN
NO. 11
COMPLIES WITH THE BELOW AS OF 2/1/2017
SCAQMD YES OTC Phase II YES
CARB YES LADCO YES
CARB SCM 2007 YES AIM YES
OTC YES