Use and Care Manual

LIMITED WARRANTY
Behr Process Corporation warrants customer satisfaction with this product for 10 years on vertical
surfaces from date of purchase, when applied to a properly prepared surface in accordance with the
label directions. Color fading and slight natural graying of the wood may occur during this period,
especially in areas exposed to heavy foot traffic or excessive weather. If you are not satisfied with
this product, Behr will, at its option and upon proof of purchase, either furnish an equivalent amount
of new product or refund the purchase price. This warranty is made to the original residential
product purchaser and is not transferable. This warranty excludes (1) labor and costs of labor
for application or removal of any product or (2) any incidental or consequential damages,
whether based upon breach of express or implied warranty, negligence, strict liability or
any other legal theory. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
BEHR
®
Solid Color House & Fence Wood Stain
• Oil-Latex Formula
• Self-Priming
• Resists Moisture, Cracking & Blistering
• Mildew Resistant Finish
CAUTION: Stained surfaces may become slippery when wet.
WHERE TO USE
Recommended for smooth or rough sawn exterior vertical wood
surfaces such as: Plywood, Fences, Patio Covers, Shingles, Shakes,
Siding, Laminates, Barns and Masonry & Stucco Surfaces. Do not use
on horizontal surfaces subject to foot traffic.
PREPARATION †
(The following steps and products are required.) Use a product such
as BEHR PREMIUM
®
NO. 64 Wood Stain & Finish Stripper on failing
areas to remove latex, oil-based and 100% acrylic coatings.
BEHR PREMIUM NO. 63 All-In-One Wood Cleaner MUST be used
following NO. 64 to clean, brighten & neutralize wood. When NO. 64 is
not needed, use a product such as NO. 63 to clean and brighten the
wood surface and to remove light to medium exterior stains caused by
mold, mildew, algae & fungus. Rinse thoroughly and allow to dry before
coating. On new wood, use a product such as NO. 63 to remove mill
glaze and open the pores of the wood. Lightly sand to remove remaining
wood fibers/fuzz.
APPLICATION
Must apply between 40-90˚ F (4.5-32˚ C). Do not use if rain is expected
within 24 hours. The wood surface must be completely dry before
application. No primer needed on most woods. However, Redwood,
Cedar, Cypress and other “bleeding” woods contain water soluble
extractives which may cause discoloration of white and pastel colors;
therefore prime the above type woods with one coat of a product such
as BEHR PREMIUM PLUS
®
NO. 436 Exterior Multi-Purpose Primer &
Sealer. See label for additional instructions. Intermix multiple containers
to ensure color uniformity. Apply with a nylon/polyester brush. On
rough-sawn or textured wood apply with a 3/4” (19 mm) long nap roller
or high quality airless sprayer. For airless spraying use a .015 - .019”
tip. Pump Sprayer not recommended. Always back-brush or back-roll
during all application methods. Keep a wet edge to reduce lapping
and help control color uniformity. Over application of stain will lead to
surface failure including peeling and cracking. Avoid applying stain
too heavily. Two thin coats recommended.
DRY TIME
6-8 hours before recoat. Allow 72 hours for full cure.
DISPOSAL
For disposal of empty containers and unused product contact your
household refuse collection service.
† WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-
approved respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
WARNING! Sanding or scraping pressure treated lumber may be
hazardous; wear appropriate protection.
A quality product that contains a mildewcide will assist in providing a finish that is resistant to
mildew, provided that all existing mildew is removed prior to application. While this product does
contain a mildewcide, it will not prevent mildew growth.
WARNING! IRRITANT! HARMFUL IF SWALLOWED. CONTAINS: ETHYLENE GLYCOL.
MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND
EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION
AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing
vapors and spray mist, open windows and doors or use other means to ensure fresh air
entry during application and drying. If you experience eye watering, headaches or dizziness,
increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with P
series particulate pre-filter) may offer additional protection; obtain professional advice before
using. A dust mask does not provide protection against vapors. Avoid contact with eyes
and skin. Wash thoroughly after handling. Close container after each use. FIRST AID: If you
experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is
experienced, get medical assistance immediately. In case of eye contact, flush immediately
with plenty of water for at least 15-20 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
WARNING! This product contains chemicals known to the state of California to cause cancer
and birth defects or other reproductive harm.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
©2013 Behr Process Corporation
Santa Ana, CA 92704 U.S.A. • behr.com
V.O.C. (C.O.V.) <100 g/L • REV. 3/13
Must Prep
Before Staining
Soap & Water
Clean-Up
2 Thin Coats
Recommended
1 2
Spread Rate:
1
st
Coat 200-400 Sq. Ft.
2
nd
Coat 250-500 Sq. Ft.
No. 11 White
No. 30 Deep Base