TDS
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2015 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
TECHNICAL DATA SHEET
Revised 11/2015
2 of 2
sanding, abrasion, or chemical etching. Oil lms: (especially
on new or non-ferrous metals) should be removed by
scrubbing the surface with a detergent and water solution,
and thoroughly rinsed. Rust and Mill Scale: Remove all
rust and mill scale using sandpaper, steel wool, abrasive
blasting, or other abrading methods. Prole: For best
adhesion results, sand all metal surfaces (including new
ones) with sandpaper, steel wool, or etch using a chemical
etcher. Clean by scrubbing the surface with a detergent and
water solution, followed by a thorough rinsing with clean
water. All ferrous metals must be primed the same day it is
cleaned to prevent rust.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Wood:
• BEHR PREMIUM PLUS® Exterior Water-Based Primer
& Sealer No 436
Ferrous and Non-Ferrous Metals:
• BEHR PREMIUM PLUS Exterior Water-Based Primer
& Sealer No 436
Drywall/Wallboard:
• Self priming, two coats recommended.
NEW SURFACES:
• All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust and all other foreign substances.
PREVIOUSLY PAINTED SURFACES:
• Use a full coat or spot prime with BEHR® Masonry,
Stucco & Brick Flat Paint.
TEST SPECIFICATIONS:
Scrubbability:
ASTM D2486 Scrub > 2500 (no shim)
Biological Growth:
ASTM D3273 (4 weeks) – Pass
Accelerated Weathering:
ASTM D4587, 500 hrs exposure - Pass
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers and unused product, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply at temperatures between
50°F - 90°F. Temperatures above 90°F may aect the
application such as drying too fast. Avoid painting in
direct sun. NOTE: If the surface is hot to the touch it
should be considered too hot to apply this coating.
• Avoid heavy trac for 24 hours.
• Allow two weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused, contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
MASONRY, STUCCO & BRICK FLAT PAINT
NO. 270 WHITE