TDS

TECHNICAL DATA SHEETTECHNICAL DATA SHEET
PAINT + PRIMER SPRAY PAINT
PRODUCT INFORMATION
BEHR® Paint + Primer Spray Paint delivers a premium nish with excellent adhesion to multiple surfaces. Ideal for small indoor
and outdoor projects and highly detailed surfaces. BEHR Paint + Primer Spray Paint can be used on wood, metal, plastic, cast
stone and wicker. The comfort tip reduces nger fatigue and delivers a great application experience.
RECOMMENDED USES:
Ideal for use on properly prepared surfaces such as:
• Wood • Metal • Plastic • Cast Stone • Wicker
CONTAINER CAP PROVIDES CLOSE APPROXIMATION OF COLOR AND SHEEN OF THE PRODUCT.
PRODUCT SPECIFICATIONS:
Colors:
B000144 Black Gloss
B000244 Orion Gray Gloss
B000344 Lunar Surface Gloss
B000444 Hidden Sea Glass Gloss
B000544 Inked Gloss
B000644 Blazing Bonre Gloss
B000744 Baronial Brown Gloss
B000844 No More Drama Gloss
B000944 Flirt Alert Gloss
B001044 Unmellow Yellow Gloss
B001144 Luck of the Irish Gloss
B001244 Congo Gloss
B001344 Venom Gloss
B001444 Tropics Gloss
B001544 Mayan Treasure Gloss
B001644 Sugar Beet Gloss
B001744 Outdoor Café
B001844 Khaki Shade Gloss
B001944 White Gloss
B002044 White Flat
B002144 Black Flat
B002244 Lunar Surface Flat
B002344 Clear Flat
B002444 Resort Sunrise Gloss
B004744 White Primer
B004944 Gray Primer
B005044 O White 73
Finish:
Flat: < 5 @ 60
Gloss: > 80 @ 60
Sheen level depends on porosity of surface and various
surface irregularities.
Resin Type: Modied Alkyd
Net Weight: 12 oz / 340 g
*% Solids by Volume: 33% ± 2%
*% Solids by Weight: 44% ± 2%
Max VOC (by weight): 60%
Max Product-Weighted MIR:
Flat: 0.80
Non-Flat: 0.95
Coverage: Up to 15 sq ft per can, depending on the surface
texture, porosity and application method. Does not include
the loss of material from spraying.
SURFACE PREPARATION:
• The surface must be clean, free of dust, grease, wax,
peeling paint, mold and mildew. If washing is necessary,
use a non-soapy detergent or a TSP substitute. Rinse well
and allow to dry.
• Scrape o loose paint and sand to a smooth surface.
• For maximum adhesion, sand glossy surfaces thoroughly
before coating.
Stain-Blocking:
• If stain-blocking performance is required, apply a coat of
primer such as KILZ® ORIGINAL Interior/Exterior Oil-Based
Aerosol Primer No. 1008.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
APPLICATION:
• Shake can vigorously for 1 minute after mixing ball begins
to rattle and often during use.
• Test your spray application technique on a scrap surface or
inconspicuous area before starting the project.
• Hold can upright, moving from side-to-side while spraying
lightly and evenly about 12” from area being painted.
Always start and nish spraying o the object. Each spray
pass should overlap the previous pass by half.
• Apply multiple thin coats to prevent dripping and sagging.
Allow to dry between each coat.
Dry Time: @ 77°F & 50% RH:
To Touch: 15 minutes
Re-coat: Before 1 hour or after 24 hours
Dry times are temperature, humidity, and lm thickness
dependent
CLEANUP/DISPOSAL:
• Clear spray valve immediately after use by turning can
upside down and spraying until only clear gas is released.
If spray nozzle becomes clogged, remove and clean with
paint thinner or mineral spirits where allowed.
• Do not stick pins or wire into spray nozzle opening.
• Clean fresh overspray with VOC-compliant paint thinner
or mineral spirits. Otherwise use acetone. Remove dried
paint with paint remover, but test small area rst to ensure
paint remover does not damage substrate.
• Wipe o tip before storing.
• Do not burn or place in home trash compactor.
• For recycling or disposal information, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Temperature and humidity extremes can aect dry time
and nal appearance.
• Apply if surface, air and product temperatures are
between 50° – 90°F.
• Avoid painting in direct sunlight.
• Avoid spraying in very windy and dusty conditions.
• Ensure adequate ventilation when spraying indoors.
• Cover adjacent areas to avoid overspray.
• Do not apply directly to galvanized steel without rst
applying a metal primer.
• Not for touch-up on surfaces previously painted with non-
aerosol BEHR paint.
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature
are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
*Values given here are from BEHR® Paint + Primer Spray Paint Gloss Enamel White.
Revised 10/2020
1 of 2