TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 10/2019
PRODUCT INFORMATION
BEHR® Fast-Drying Water-Based Wood Stain is designed for smooth application and easy workability to all interior wood
surfaces such as cabinets, trim, doors, paneling, furniture and floors. This product provides superior color control, one coat
coverage and lower odor than oil-based products.
RECOMMENDED USES:
Ideal for properly prepared interior , smooth unfinished, unsealed or stripped wood surfaces, including floors.
PRODUCT SPECIFICATIONS:
Tint Base/Max Tint Load:
No. B4500 Tint Base 29 fl oz / 3 fl oz (quart)
No. B4500 Tint Base 7.25 fl oz / 0.75 fl oz (half-pint)
Premixed Colors: Available in 17 colors
Gloss: n/a
Resin Type: Acrylic
Weight per Gallon: 8.5-8.8 lb
% Solids by Volume: 10-13 % ± 2%
% Solids by Weight: 12-16 % ± 2%
VOC: < 250 g/L
Flash Point: N/A
Viscosity: 75-85 KU
Recommended Film Thickness: n/a
Coverage: Up to 400 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
Stir stain thoroughly before and occasionally during use. Do
not thin. Apply stain in the direction of the grain with a brush
or clean cloth. Allow to penetrate for 5 to 10 minutes. The
more time the stain is allowed to penetrate, the richer and
darker the color will be. Remove stain that has not absorbed
into the wood with a clean cloth. Wipe in the direction of the
grain, while blending light and dark areas to obtain uniform
color. Do not allow stain that has not penetrated into the
wood to dry on the wood surface. To darken the color, apply a
second coat after 1 hour, repeating directions above. Do not
sand between coats of stain. Allow stain to dry for a minimum
of 1 hour before applying a BEHR clear protective finish.
Brush: Nylon/polyester brush
Thinning: DO NOT THIN
Dry Time: @ 77°F & 50% RH
To Touch: 1 hr
Topcoat: 1 hr
SURFACE PREPARATION:
FAST -DRY INR WATER - BASED WOOD STAIN
R
NO. B4500 SERIES
COMPLIES WITH THE BELOW AS OF 10 /1/2019
SCAQMD YES
AIM
YES
CARB SCM 2007 YES
CARB YES YES
OTC PHASE II YES
OTC
YES
LADCO
CAUTIONS/LIMITATIONS:
• Always test stain on an inconsipicuous area of the wood to
verify desired color.
• Shelf life under normal conditions is 2 years unopened.
• Recommended finishes include BEHR Fast-Drying
Polyurethane or BEHR Spar Urethane. Slight ambering may
occur when these clear finishes are applied over light-
colored stains. Always spot test on an inconspicuous area
to ensure satisfactory results.
All surfaces must be clean, free of dust, oil, grease, wax,
polish , glue and existing coatings before staining.
New Wood: Sand with #120-grit sandpaper followed by #180-
grit or finer for a smoother finish if desired. Remove all dust.
Previously Finished Wood: Lightly sand surface with a 400-
grit sandpaper. Remove all dust. To ensure uniform stain color
and beautiful results on bare wood, apply BEHR Water-Based
Pre-Stain Wood Conditioner prior to staining. Follow label
instructions.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA vacuum
and a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National Lead
Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused produc in
accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
GENERAL INFORMATION:
WARNING IRRITANT CONTAINS: ETHYLENE GLYCOL.
MAY CAUSE DAMAGE TO ORGANS (KIDNEY) THROUGH
PROLONGED AND REPEATED EXPOSURE.MAY CAUSE EYE, SKIN,
NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN
AND EYES AND AVOID BREATHING VAPORS AND SPRAY MIST.
WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE
WITH ADEQUATE VENTILATION. To avoid breathing vapors
and spray mist, open windows and doors or use other means
to ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase fresh
air. If properly used, a respirator (NIOSH-approved for organic
vapor with P series particulate pre-filter) may offer additional
protection; obtain professional advice before using. A dust
mask does not provide protection against vapors. Avoid
contact with eyes and skin. Wash thoroughly after handling.
Close container after each use. FIRST AID: If you experience
difficulty in breathing, leave the area to obtain fresh air. If
continued difficulty is experienced, get medical assistance
immediately. In case of eye contact, flush immediately with
plenty of water for at least 20 minutes and get medical
attention; for skin, wash thoroughly with soap and water. If
swallowed, get medical attention immediately. CAUTION: KEEP
OUT OF REACH OF CHILDREN-DO NOT TAKE INTERNALLY.