TDS

TECHNICAL DATA SHEETTECHNICAL DATA SHEET
WATER-BASED STAIN & POLY IN ONE
NO. B6200 SATIN & B6300 GLOSS SERIES
PRODUCT INFORMATION
BEHR® WATER-BASED STAIN & POLY IN ONE is designed to provide time-saving application by delivering rich color and protection
in one step to all interior wood surfaces. This product enhances wood grain and has less odor than oil-based products.
RECOMMENDED USES:
Properly prepared interior surfaces such as furniture, moldings, cabinets, trim, and wood doors. Do not use on oors.
COMPLIES WITH THE BELOW AS OF 6/1/2020
SCAQMD
YES OTC YES
CARB SCM 2007
YES LADCO YES
OTC PHASE II
YES AIM YES
PRODUCT SPECIFICATIONS:
Tint Base/Max Tint Load:
No. B6201 Satin Tint Base 31  oz / 1.5  oz (quart)
No. B6301 Gloss Tint Base 31  oz / 1.5  oz (quart)
Premixed Colors: Available in 8 colors
Finish: Satin: 20 – 30 @ 60° | Gloss: > 85 @ 60°
Resin Type: Polyurethane/Acrylic
Weight per Gallon: 8.5 – 8.8 lb
% Solids by Volume: 29% ± 2%
% Solids by Weight: 31% ± 2%
VOC: < 275 g/L
Flash Point: N/A
Viscosity: 7 – 15 s (Zahn #3 Cup)
Recommended Film Thickness:
Wet: 2.8 mils / Dry: 0.8 mils @ 500 sq ft/gal per gallon
For maximum durability, 2 coats are required.
Coverage: Up to 500 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
Stir BEHR Water-Based Stain & Poly In One thoroughly
before and occasionally during use. Using a high quality
nylon/polyester bristle brush, dip approximately an inch into
the can, gently tapping it against the inside to remove any
excess. Apply a very THIN, even coat following the direction
of the grain. Make sure to maintain a “wet” edge. To
minimize the brush marks and bubbles after staining, tip o
the surface by holding the brush at a 45 degree angle and
lightly run the bristles over the entire length of the wood.
Let the rst coat dry for 1 hour or more. Dry time may be
extended due to high humidity, low temperatures, and
inadequate ventilation or if the coat is applied too thick.
Lightly sand the surface between coats with ne sand paper
(#400 grit). Remove all dust. Brush on a second thin coat
following directions above. To deepen the color, apply a
third coat. NOTE: For additional protection, without adding
color, add a coat of BEHR Fast Drying Polyurethane.
Brush: Nylon/Polyester
Thinning: Do not thin. Product is formulated for use at
package consistency only.
Dry Time: @ 77°F & 50% RH
Longer dry time may be required in cooler temperatures and
higher humidity.
To Touch: 1 hr
Recoat: 1 hr
Light Use: 12 – 24 hrs
Full Cure: 3 days
SURFACE PREPARATION:
All surfaces must be clean, free of dirt, dust, oil, grease, wax,
polish and glue.
New Wood: Sand the wood in the direction of the grain
using ne-grade sandpaper (#150 – 220 grit) until smooth.
Remove all sanding dust. To help ensure uniform acceptance
of stain color and beautiful results, pretreat new or raw
wood with BEHR® Water-Based Pre Stain Wood Conditioner,
following label directions.
Previously Finished Wood that is not being stripped:
Lightly sand surface with a 400-grit sandpaper to ensure
adhesion. Remove all dust.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at
CLEANUP/DISPOSAL:
Clean all tools and equipment with warm, soapy water.
Do not dispose of this product down a drain. If spilled,
contain material and remove with an inert absorbent.
Dispose of contaminated absorbent, container and unused
product in accordance with all current federal, state
and local regulations. For recycling or disposal of empty
containers, unused product and soiled rags, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Always test Water-Based Stain & Poly in One on a scrap
piece or hidden area of wood to verify desired color.
• Shelf life under normal conditions is two years unopened.
• Recommended nishes include BEHR Fast-Drying
Polyurethane or BEHR Spar Urethane. Slight ambering
may occur when these clear nishes are applied over
light-colored stains. Always spot test on an inconspicuous
area to ensure satisfactory results.
GENERAL INFORMATION:
WARNING IRRITANT CONTAINS: ETHYLENE GLYCOL. MAY
CAUSE DAMAGE TO ORGANS (KIDNEY) THROUGH PROLONGED
AND REPEATED EXPOSURE. MAY CAUSE EYE, SKIN, NOSE AND
THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES
AND AVOID BREATHING VAPORS AND SPRAY MIST. WEAR
EYE PROTECTION AND PROTECTIVE CLOTHING. USE WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH-approved for
organic vapor with P series particulate pre-lter) may oer
additional protection; obtain professional advice before
using. A dust mask does not provide protection against
vapors. Avoid contact with eyes and skin. Wash thoroughly
after handling. Close container after each use.
FIRST AID: If you experience diculty in breathing,
leave the area to obtain fresh air. If continued diculty is
experienced, get medical assistance immediately. In case of
eye contact, ush immediately with plenty of water for at
least 20 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, get medical
attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT
TAKE INTERNALLY.
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature are
made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call 1-800-854-0133 Ext. 2
(U.S.A. only). ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 6/2020