TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call
1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 1/2020
PRODUCT INFORMATION
BEHR® WATER-BASED STAIN & POLY IN ONE is designed to provide time-saving application by delivering rich color and
protection in one step to all interior wood surfaces. This product enhances wood grain and has less odor than oil-based
products.
RECOMMEND
ED USES:
Properly prepared interior surfaces such as furniture, moldings, cabinets, trim, and wood doors. Do not use on floors.
PRODUCT SPECIFICATIONS:
Tint Base/Max Tint Load:
No. B6201 Satin Tint Base 31 fl oz / 1.5 fl oz (quart)
No. B6301 Gloss Tint Base 31 fl oz / 1.5 fl oz (quart)
Premixed Colors: Available in 8 colors
Finish : Satin - 20–30 @ 60° | Gloss - > 85 @ 60°
Resin Type: Polyurethane/A crylic
Weight per Gallon: 8.5–8.8 lb
% Solids by Volume: 29 % ± 2%
% Solids by Weight: 31 % ± 2%
VOC: < 275 g/L
Flash Point: N/A
Viscosity: 7–15 s (Zahn #3 Cup)
Recommended Film Thickness:
Wet: 2.8 mils / Dry: 0.8 mils @ 500 sq ft/gal per gallon
For maximum durability, 2 coats are required.
Coverage: Up to 500 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
Stir BEHR Water-Based Stain & Poly In One thoroughly before
and occasionally during use. Using a high quality nylon/
polyester bristle brush, dip approximately an inch into the
can, gently tapping it against the inside to remove any
excess. Apply a very THIN, even coat following the direction
of the grain. Make sure to maintain a “wet” edge. To
minimize the brush marks and bubbles after staining, tip off
the surface by holding the brush at a 45 degree angle and
lightly run the bristles over the entire length of the wood.
Let the first coat dry for 1 hour or more. Dry time may be
extended due to high humidity, low temperatures, and
inadequate ventilation or if the coat is applied too thick.
Lightly sand the surface between coats with fine sand paper
(#400 grit). Remove all dust. Brush on a second thin coat
following directions above. To deepen the color, apply a
third coat. NOTE: For additional protection, without adding
color, add a coat of BEHR Fast Drying Polyurethane.
Brush: Nylon/polyester brush
To T
ouch: 1 h
r
Recoat: 1 hr
Light Use: 12–24 hrs
Full Cure: 3 days
SURFACE PREPARATION:
WATER-BASED STAIN & POLY IN ONE
R
NO. B6200 SATIN & B6300 GLOSS SERIES
COMPLIES WITH THE BELOW AS OF 1 /1/20 2 0
SCAQMD YES
AIM
YES
CARB SCM 2007 YES
CARB YES YES
OTC PHASE II YES
OTC
YES
LADCO
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Always test Water-Based Stain & Poly in One on a scrap
piece or hidden area of wood to verify desired color.
• Shelf life under normal conditions is 2 years unopened.
• Recommended finishes include BEHR Fast-Drying
Polyurethane or BEHR Spar Urethane. Slight ambering
may occur when these clear finishes are applied over
light-colored stains. Always spot test on an
inconspicuous area to ensure satisfactory results.
All surfaces must be clean, free of dirt, dust, oil, grease, wax,
polish and glue.
New Wood: Sand the wood in the direction of the grain using
fine-grade sandpaper (#150-220 grit) until smooth. Remove all
sanding dust. To help ensure uniform acceptance of stain color
and beautiful results, pretreat new or raw wood with BEHR®
Water-Based Pre Stain Wood Conditioner, following label
directions.
Previously Finished Wood that is not being stripped:
Lightly sand surface with a 400-grit sandpaper to ensure
adhesion. Remove all dust.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused produc in
accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
GENERAL INFORMATION:
WARNING IRRITANT CONTAINS: ETHYLENE GLYCOL.
MAY CAUSE DAMAGE TO ORGANS (KIDNEY) THROUGH
PROLONGED AND REPEATED EXPOSURE.MAY CAUSE EYE,
SKIN, NOSE AND THROAT IRRITATION. AVOID CONTACT
WITH SKIN AND EYES AND AVOID BREATHING VAPORS
AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE
CLOTHING. USE WITH ADEQUATE VENTILATION. To avoid
breathing vapors and spray mist, open windows and doors
or use other means to ensure fresh air entry during
application and drying. If you experience eye watering,
headaches or dizziness, increase fresh air. If properly used, a
respirator (NIOSH-approved for organic vapor with P series
particulate pre-filter) may offer additional protection; obtain
professional advice before using. A dust mask does not
provide protection against vapors. Avoid contact with eyes
and skin. Wash thoroughly after handling. Close container
after each use. FIRST AID: If you experience difficulty in
breathing, leave the area to obtain fresh air. If continued
difficulty is experienced, get medical assistance
immediately. In case of eye contact, flush immediately with
plenty of water for at least 20 minutes and get medical
attention; for skin, wash thoroughly with soap and water.
If swallowed, get medical attention immediately. CAUTION:
KEEP OUT OF REACH OF CHILDREN-DO NOT TAKE
INTERNALLY.
Thinning: Do not thin. Product is formulated for use at
package consistency only.
Dry Time: @ 77°F & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.