Use and Care Manual

BEHR
®
WATER-BASED
STAIN & POLY IN ONE
©2019 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. (C.O.V.) <275 g/L • REV. 7/19
• Delivers Rich Color and Protection in One Step
• Can Be Used Over Polyurethane Finishes
• Dries in 1 Hour
• Time Saving Application
• Enhances Wood Grain
• Less Odor than Oil-Based Products
Clean-Up:
Soap & Water
Prep Before Use
2 Coats Required
Spread Rate:
125 Sq. Ft./Qt.
No. B6200 Series
Available in a Tint Base and
Assorted Pre-tinted Colors
READY TO USE. PROTECT FROM FREEZING.
WHERE TO USE: Properly prepared interior surfaces such as
furniture, moldings, cabinets, trim, and wood doors.
Do not use on floors.
CAUTION: Surface may be slippery when wet.
SURFACE PREPARATION
†
(Proper surface preparation is required)
FOR STRIPPED, UNSTAINED OR RAW WOOD:
• Before starting, surface must be dry, clean and free of dirt, grease
and glue.
• Sand the wood in the direction of the grain using ne-grade
sandpaper (#150-220 grit) until smooth. Remove all sanding dust.
• To help ensure uniform acceptance of stain color and beautiful
results, pretreat new or raw wood with BEHR
®
Water-Based
Pre-Stain Wood Conditioner, following label directions.
FOR PREVIOUSLY FINISHED WOOD THAT IS NOT BEING STRIPPED:
• Before starting, surface must be dry, clean and free of dirt, grease
and glue.
• Lightly sand the existing nish with 400 grit sandpaper to ensure
adhesion. Remove all sanding dust.
PRODUCT PREPARATION AND COLOR TESTING
• Stir BEHR Stain & Poly In One thoroughly before and occasionally
during use. Do not thin.
• Always test Stain & Poly on a scrap piece or hidden area of wood
to verify desired color.
APPLICATION
• Using a high quality nylon/polyester bristle brush, dip
approximately an inch into the can, gently tapping it against
the inside to remove any excess. Apply a very THIN, even coat
following the direction of the grain. Make sure to maintain a
“wet” edge.
• To minimize the brush marks and bubbles after staining, tip off
the surface by holding the brush at a 45 degree angle and lightly
run the bristles over the entire length of the wood.
PLEASE SEE PRODUCT LABEL FOR SPECIFIC
WARNINGS. WARNINGS MAY VARY BETWEEN
PRODUCTS AND OR COLORS.
WARNING Cancer and Reproductive Harm –
www.P65Warnings.ca.gov
CAUTION IRRITANT CONTAINS: PARAFFIN, HYDROCARBON WAX AND ISOTHIAZOLONE.
MAY CAUSE AN ALLERGIC SKIN REACTION AND EYE, SKIN, NOSE AND THROAT IRRITATION. AVOID
CONTACT WITH SKIN AND EYES AND AVOID BREATHING VAPORS AND SPRAY MIST. WEAR EYE
PROTECTION AND PROTECTIVE CLOTHING. USE WITH ADEQUATE VENTILATION. To avoid breathing
vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH-approved for organic
vapor with P series particulate pre-filter) may offer additional protection; obtain professional advice before using. A dust mask
does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container
after each use. FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is
experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 20
minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN-DO NOT TAKE INTERNALLY.
• Let the rst coat dry for 1 hour or more. Dry time may be
extended due to high humidity, low temperatures, and inadequate
ventilation or if the coat is applied too thick.
• Lightly sand the surface between coats with ne sand paper
(#400 grit). Remove all dust. Brush on a second thin coat
following directions above. To deepen the color, apply a third coat.
NOTE: For additional protection, without adding color, add a coat
of BEHR Fast Drying Water-Based Polyurethane. Please refer to
the back label of the container for application instructions.
DISPOSAL
• For disposal of empty containers and unused product contact your
household refuse collection service.
LIMITED WARRANTY
• Visit behr.com/warranty or call 1-800-854-0133 Ext. 2 for more
information.
†
WARNING If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information
Center at 1-800-424-LEAD or log on to www.epa.gov/lead.