Use and Care Manual

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 10/2019
PRODUCT INFORMATION
BEHR® WATER-BASED STAIN & POLY IN ONE is designed to provide time-saving application by delivering rich color and
protection in one step to all interior wood surfaces. This product enhances wood grain and has less odor than oil-based
products.
RECOMMENDED USES:
Properly prepared interior surfaces such as furniture, moldings, cabinets, trim, and wood doors. Do not use on floors.
PRODUCT SPECIFICATIONS:
Tint Base/Max Tint Load:
No. B6201 Satin Tint Base 31 fl oz / 1.5 fl oz (quart)
No. B6301 Gloss Tint Base 31 fl oz / 1.5 fl oz (quart)
Premixed Colors: Available in 8 colors
Finish : Satin - 20–30 @ 60° | Gloss - > 85 @ 60°
Resin Type: Polyurethane/Acrylic
Weight per Gallon: 8.5–8.8 lb
% Solids by Volume: 29 % ± 2%
% Solids by Weight: 31 % ± 2%
VOC: < 275 g/L
Flash Point: N/A
Viscosity: 7–15 s (Zahn #3 Cup)
Recommended Film Thickness:
Wet: 2.8 mils / Dry: 0.8 mils @ 500 sq ft/gal per gallon
For maximum durability, 2 coats are required.
Coverage: Up to 500 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
Stir BEHR Stain & Poly In One thoroughly before and
occasionally during use. Using a high quality nylon/polyester
bristle brush, dip approximately an inch into the can, gently
tapping it against the inside to remove any excess. Apply a very
THIN, even coat following the direction of the grain. Make sure
to maintain a “wet” edge. To minimize the brush marks and
bubbles after staining, tip off the surface by holding the brush
at a 45 degree angle and lightly run the bristles over the entire
length of the wood. Let the first coat dry for 1 hour or more.
Dry time may be extended due to high humidity, low
temperatures, and inadequate ventilation or if the coat is
applied too thick. Lightly sand the surface between coats with
fine sand paper (#400 grit). Remove all dust. Brush on a second
thin coat following directions above. To deepen the color, apply
a third coat. NOTE: For additional protection, without adding
color, add a coat of BEHR Fast Drying Polyurethane.
To Touch: 1 hr
Recoat: 1 hr
Light Use: 12–24 hrs
Full Cure: 3 days
SURFACE PREPARATION:
WATER-BASED STAIN & POLY IN ONE
R
NO. B6200 SATIN & B6300 SEMI-GLOSS SERIES
COMPLIES WITH THE BELOW AS OF 10 /1/2019
SCAQMD YES
AIM
YES
CARB SCM 2007 YES
CARB YES YES
OTC PHASE II YES
OTC
YES
LADCO
CAUTIONS/LIMITATIONS:
• Always test Stain & Poly on a scrap piece or hidden area of
wood to verify desired color.
• Shelf life under normal conditions is 2 years unopened.
• Recommended finishes include BEHR Fast-Drying
Polyurethane or BEHR Spar Urethane. Slight ambering may
occur when these clear finishes are applied over light-
colored stains. Always spot test on an inconspicuous area
to ensure satisfactory results.
All surfaces must be clean, free of dirt, dust, oil, grease, wax,
polish and glue.
New Wood: Sand the wood in the direction of the grain using
fine-grade sandpaper (#150-220 grit) until smooth. Remove all
sanding dust. To help ensure uniform acceptance of stain color
and beautiful results, pretreat new or raw wood with BEHR®
Water-Based Pre Stain Wood Conditioner, following label
directions.
Previously Finished Wood that is not being stripped:
Lightly sand surface with a 400-grit sandpaper to ensure
adhesion. Remove all dust.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused produc in
accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
GENERAL INFORMATION:
WARNING IRRITANT CONTAINS: ETHYLENE GLYCOL.
MAY CAUSE DAMAGE TO ORGANS (KIDNEY) THROUGH
PROLONGED AND REPEATED EXPOSURE.MAY CAUSE EYE, SKIN,
NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN
AND EYES AND AVOID BREATHING VAPORS AND SPRAY MIST.
WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE
WITH ADEQUATE VENTILATION. To avoid breathing vapors
and spray mist, open windows and doors or use other means
to ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase fresh
air. If properly used, a respirator (NIOSH-approved for organic
vapor with P series particulate pre-filter) may offer additional
protection; obtain professional advice before using. A dust
mask does not provide protection against vapors. Avoid
contact with eyes and skin. Wash thoroughly after handling.
Close container after each use. FIRST AID: If you experience
difficulty in breathing, leave the area to obtain fresh air. If
continued difficulty is experienced, get medical assistance
immediately. In case of eye contact, flush immediately with
plen ty of water for at least 20 minutes and get medical
attention; for skin, wash thoroughly with soap and water. If
swallowed, get medical attention immediately. CAUTION: KEEP
OUT OF REACH OF CHILDREN-DO NOT TAKE INTERNALLY.
Dry Time: @ 77°F & 50% RH
Longer dry time may be required in cooler temperatures and
higher humidity.
Brush: Nylon/polyester brush
Thinning: DO NOT THIN