TDS
TECHNICAL DATA SHEETTECHNICAL DATA SHEET
FAST DRYING OIL-BASED POLYURETHANE AEROSOL
NO. B7110 SERIES
PRODUCT INFORMATION
BEHR® Fast Drying Oil-Based Polyurethane is designed to provide a durable clear nish that protects and beauties interior
wood surfaces. This product resists stains and scratches. Available in four sheens: Matte, Satin, Semi-Gloss and Gloss.
RECOMMENDED USES:
Ideal for properly prepared interior unnished and nished surfaces such as furniture, moldings, cabinets, trim, wood and
doors.
PRODUCT SPECIFICATIONS:
Finish: B7116 Matte: 5 - 15 @ 60°
B7110 Satin: 20 – 30 @ 60°
B7112 Semi-Gloss: 50 – 60 @ 60°
B7114 Gloss: > 85 @ 60°
Resin Type: Polyurethane
Net Weight: 11.5 oz / 326 g
% Solids by Volume: 9% ± 2%
% Solids by Weight: 14% ± 2%
Max VOC (by weight): 67%
Max Product-Weighted MIR: 0.85
Coverage: 15 – 20 sq ft per can
APPLICATION:
Shake can vigorously for 1 minute after mixing ball begins
to rattle and often during use. Protect adjacent areas
from overspray. Hold can vertically 12 inches from surface.
Depress button fully and spray using an even, sweeping
motion with slightly overlapping strokes.
On unnished wood, apply sucient material to seal open
joints, edges and end-grain. Apply thin coats to avoid runs
and sags. Recoat within 1 hour. If unable to do so, wait a
minimum of 72 hours, then lightly sand and recoat.
Apply at least 3 coats on unnished wood and 2 coats on
surfaces already nished. After nal coat, allow at least 24
hours before normal use
Dry Time: @ 77°F & 50% RH
Lower temperature, higher humidity, lack of air movement
or application of thick coats will extend drying times.
To Touch: 2 hours
To Recoat: 2 – 4 hours
Full Cure: 72 hours
SURFACE PREPARATION:
All surfaces must be clean, free of dust, oil, grease, wax,
polish, glue and all other foreign substances.
For renishing, remove all wax or cleaner build-up with a
wax stripper or degreaser prior to sanding. Sand all surfaces
in the direction of the wood grain to desired smoothness. DO
NOT USE steel wool. Remove all dust from sanded surfaces
with tack cloth. If desired, apply BEHR® Wood Stain.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEANUP/DISPOSAL:
• Wet overspray can be removed with mineral spirits.
• After each use, clear valve by holding can upside down and
spraying until only clear gas comes out.
• If spray button becomes clogged, wear eye protection,
wipe o button opening with lacquer thinner. Do NOT stick
pin in spray button opening.
• Wipe o tip before storing.
• Rags, steel wool and waste soaked with BEHR FAST DRYING
OIL-BASED POLYURETHANE may spontaneously catch re
if improperly discarded or stored. To avoid a spontaneous
combustion re immediately after use, place rags, steel
wool or waste in a sealed water-lled, metal container.
Do not store unused product inside the home. For disposal
guidance, contact your household refuse collection
service, re department, county or state government
control agency.
• Do not burn or place in home trash compactor.
.
CAUTIONS/LIMITATIONS:
• Do not apply in direct sunlight or in temperatures below
55°F or above 90°F.
• Slight ambering may be experienced when BEHR Fast
Drying Oil-Based Polyurethane is applied over light-
colored wood surfaces.
• Always spot test on an inconspicuous area to ensure
satisfactory result.
GENERAL INFORMATION:
VENTILATION REQUIRED: To avoid inhalation and
combustion hazards (see below), DO NOT use this product
unless you can achieve cross ventilation by opening
windows and doors during application and drying.
CONTAINS ACETONE, PROPANE, NAPTHA, BUTANE AND
PETROLEUM DISTILATES. HARMFUL OR FATAL IF SWALLOWED.
VAPOR HARMFUL. May aect the brain or nervous system
causing dizziness, headache or nausea. CAUSES SERIOUS
EYE IRRITATION. IRRITATES SKIN, NOSE AND THROAT. Do
not breathe vapors or spray mist. If you experience eye
watering, headaches or dizziness, increase fresh air, wear
respiratory protection (NIOSH/MSHA TC 23C or equivalent)
or leave the area. NOTICE: Reports have associated repeated
and prolonged occupational overexposure to solvents with
permanent brain and nervous system damage. VAPORS
MAY IGNITE EXPLOSIVELY. Do not spray near sparks, heat
or open ame. Do not smoke. Vapors are heavier than air
and can travel at oor level to distant ignition sources.
Extinguish all ames and pilot lights and turn o stoves,
heaters, electric motors, high intensity lights and other
sources of ignition during use and until all vapors are gone.
WARNING-CONTENTS UNDER PRESSURE. Do not puncture
or incinerate container. Do not expose to heat or store at
elevated temperatures above 120°F. Prolonged exposure to
sun may cause bursting.
FIRST AID: IIf you have diculty breathing, leave area
to obtain fresh air. If diculty continues, get medical
attention immediately. If swallowed, do not induce
vomiting. Call physician immediately. In case of eye contact,
ush immediately with plenty of water for at least 20
minutes and get medical attention. For skin contact, wash
thoroughly with soap and water.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT
TAKE INTERNALLY.
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature
are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 6/2020