Use and Care Manual
BEHR
®
FAST DRYING
OIL-BASED POLYURETHANE
• Durable Clear Protective Finish
• Recoat in 2 Hours
• Resists Stains and Scratches
• Self-Leveling, Smooth Finish
• Protects & Beauties Interior Wood
• Dries to Touch in 2 Hours
No. B7100 Series
Available in
Satin, Semi-Gloss,
Gloss, and Matte
Prep Before Use
2 Coats Required
3 Coats if Desired
Spread Rate:
125 Sq. Ft. / Qt.
Clean-Up:
Mineral Spirits
or Paint Thinner
READY TO USE. PROTECT FROM FREEZING.
WHERE TO USE: Properly prepared interior bare or stained
surfaces such as furniture, moldings, cabinets, trim, wood
doors and residential hardwood oors.
CAUTION: Top coated surfaces may be slippery when wet.
SURFACE PREPARATION
†
(The following steps are recommended
for best results.) For renishing, remove all wax or cleaner build-up
with a wax stripper or degreaser prior to sanding. Sand all surfaces
in the direction of the wood grain to desired smoothness. DO NOT
USE steel wool. Remove all dust from sanded surfaces and clean
with tack cloth.
APPLICATION Do not shake or thin. Do not apply in direct sunlight
or in temperatures below 55°F (10°C) or above 90°F (32°C). Stir
thoroughly prior to and during use. If wood stain color is desired,
apply BEHR
®
Wood Stain. Follow all label instructions. Using a high
quality natural bristle brush, dip approximately an inch into the can,
gently tapping it against the inside to remove any excess. Apply a
thin, even coat following the direction of the grain making sure to
maintain a wet edge. To minimize the brush marks and bubbles
after staining application, tip off the surface by holding the brush
at a 45 degree angle and lightly run the bristles over the entire
length of the wood. Floor Application: use a lambswool or synthetic
pad applicator or synthetic bristle brush and maintain a wet edge
to avoid lap marks. For maximum durability, 3 coats are required.
Do not puddle, over-brush or overlap nishes. Sand lightly between
coats with ne sand paper. Remove all dust prior to applying
additional coats.
DRY TIME Dries to the touch in 2 hours. Sand or Recoat: 2 - 4
hours. After nal coat, allow 12 - 24 hours before light use. Fully
cured: 3 - 4 days after nal coat.
DISPOSAL For disposal of empty containers and unused product,
contact your household refuse collection service.
LIMITED WARRANTY Visit behr.com/warranty or call
1-800-854-0133 Ext. 2 for more information.
†
WARNING If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information
Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
DANGER! HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE LIQUID AND
VAPOR. MAY CONTAIN: HYDROTREATED LIGHT DISTILLATES, ALUMINUM ALKOXIDE,
NAPHTHA (PETROLEUM) and CRYSTALLINE SILICA.
CAUSES DAMAGE TO ORGANS
(CENTRAL NERVOUS SYSTEM) THROUGH PROLONGED OR REPEATED EXPOSURE.
CAUSES SERIOUS EYE IRRITATION AND IRRITATES SKIN, NOSE, AND THROAT.
MAY CAUSE AN
ALLERGIC SKIN REACTION. NOTICE: Reports have associated repeated
prolonged occupational exposure to solvents
with permanent brain damage. Intentional misuse by
deliberately concentrating and inhaling contents may be harmful or fatal. Keep away from heat
and flame. Do not smoke. Prevent build-up vapors by opening all windows and doors to achieve
cross-ventilation.
USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray
mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH-approved
for organic vapor with P series particulate pre-filter) may offer additional protection; obtain professional advice
before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash
thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing,
leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In
case of eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention;
for skin, wash thoroughly with soap and water. If swallowed, do not induce vomiting. Call physician immediately.
KEEP OUT OF REACH OF CHILDREN-DO NOT TAKE INTERNALLY.
PLEASE SEE PRODUCT LABEL FOR SPECIFIC
WARNINGS. WARNINGS MAY VARY BETWEEN
PRODUCTS AND OR COLORS.
©2021 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. (C.O.V.) <450 g/L • REV. 9/21
IMPORTANT! STORAGE AND DISPOSAL: DANGER!IMPORTANT! STORAGE AND DISPOSAL: DANGER!
Rags, steel wool
and waste soaked with BEHR OIL-BASED FAST DRYING POLY may spontaneously catch fire
if improperly discarded or stored. To avoid a spontaneous combustion fire, immediately after
use, place rags, steel wool or waste in a sealed water-filled, metal container. Do not store unused
product inside the home. For disposal guidance, contact your household refuse collection service, fire
department, county or state government control agency.
WARNING Cancer and Reproductive Harm
www.P65Warnings.ca.gov