TDS
TECHNICAL DATA SHEETTECHNICAL DATA SHEET
FAST DRYING OIL-BASED POLYURETHANE
NO. B7100 SERIES
PRODUCT INFORMATION
BEHR® Premium Fast Drying Oil-Based Polyurethane is designed to provide a self-leveling, smooth nish that protects and
beauties interior wood surfaces. This product resists stains and scratches. Available in four sheens: Matte, Satin, Semi-Gloss and
Gloss.
RECOMMENDED USES:
Ideal for properly prepared interior bare or stained surfaces such as furniture, moldings, cabinets, trim, wood doors and
residential hardwood oors. CAUTION: Topcoated surfaces may be slippery when wet.
COMPLIES WITH THE BELOW AS OF 9/1/2021
SCAQMD NO OTC* YES
CARB SCM 2007* YES LADCO* YES
OTC PHASE II* YES AIM YES
*Small Container Exemption compliance.
PRODUCT SPECIFICATIONS:
Finish: Matte: 5 – 15 @ 60°
Satin: 20 – 30 @ 60°
Semi-Gloss: 50 – 60 @ 60°
Gloss: > 85 @ 60°
Resin Type: Polyurethane
Weight per Gallon: 7.4 – 7.6 lb
% Solids by Volume: 46% ± 2%
% Solids by Weight: 50% ± 2%
VOC: < 450 g/L
Flash Point: > 100°F
Viscosity: 50 – 70 KU
Recommended Film Thickness:
Wet: 3.2 mils / Dry: 1.3 mils @ 500 sq ft/gal per coat
For maximum durability, 3 coats are required.
Coverage: Up to 500 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
Stir thoroughly prior to and during use. Do not shake or thin.
Using a high quality natural bristle brush, dip approximately
an inch into the can, gently tapping it against the inside to
remove any excess. Apply a thin, even coat following the
direction of the grain making sure to maintain a wet edge.
To minimize the brush marks and bubbles after staining
application, tip o the surface by holding the brush at a
45 degree angle and lightly run the bristles over the entire
length of the wood.
Floor Application: use a lambswool or synthetic pad
applicator or synthetic bristle brush and maintain a wet
edge to avoid lap marks. Do not puddle, over-brush or
overlap nishes. Sand lightly between coats with ne
sandpaper. Remove all dust prior to applying additional
coats.
Brush: Natural Bristle
Roller: Lambswool roller cover
Thinning: DO NOT THIN. Product is formulated for use at
package consistency only.
Dry Time: @ 77°F & 50% RH
Lower temperature, higher humidity, lack of air movement
or application of thick coats will extend drying times.
To Touch: 2 hrs
Sand or Recoat: 2 – 4 hrs
Light Use: 12 – 24 hrs
Full Cure: 3 – 4 days
SURFACE PREPARATION:
All surfaces must be clean, free of dust, oil, grease, wax,
polish, glue and all other foreign substances.
For renishing, remove all wax or cleaner build-up with a
wax stripper or degreaser prior to sanding. Sand all surfaces
in the direction of the wood grain to desired smoothness. DO
NOT USE steel wool.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEANUP/DISPOSAL:
Clean all tools and equipment with mineral spirits or paint
thinner, where allowed. Otherwise, use acetone.
DANGER! Rags, steel wool and waste soaked with BEHR
FAST-DRYING OIL-BASED POLYURETHANE may spontaneously
catch re if improperly discarded or stored. To avoid a
spontaneous combustion re, immediately after use, place
rags, steel wool or waste in a sealed water-lled, metal
container. Do not store unused product inside the home. For
disposal guidance, contact your household refuse collection
service, re department, county or state government control
agency.
CAUTION/LIMITATIONS:
• Do not use a belt or drum-type sander for sanding
between coats.
• Avoid heavy trac and replacing of furniture for 72 hours
after nal coat. When replacing furniture, do not slide. Do
not install rugs or clean oors for 7 days.
• Shelf life under normal conditions is two years unopened.
• Contents are combustible. Keep away from heat and open
ame.
GENERAL INFORMATION:
DANGER HARMFUL OR FATAL IF SWALLOWED.
COMBUSTIBLE LIQUID AND VAPOR. MAY CONTAIN:
HYDROTREATED LIGHT DISTILLATES, ALUMINUM ALKOXIDE,
NAPHTHA (PETROLEUM) and CRYSTALLINE SILICA. CAUSES
DAMAGE TO ORGANS (CENTRAL NERVOUS SYSTEM) THROUGH
PROLONGED OR REPEATED EXPOSURE. CAUSES SERIOUS EYE
IRRITATION AND IRRITATES SKIN, NOSE, AND THROAT. MAY
CAUSE AN ALLERGIC SKIN REACTION. NOTICE: Reports have
associated repeated prolonged occupational exposure to
solvents with permanent brain damage. Intentional misuse
by deliberately concentrating and inhaling contents may
be harmful or fatal. Keep away from heat and ame. Do not
smoke. Prevent build-up vapors by opening all windows
and doors to achieve cross-ventilation. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH-approved for
organic vapor with P series particulate pre-lter) may oer
additional protection; obtain professional advice before
using. A dust mask does not provide protection against
vapors. Avoid contact with eyes and skin. Wash thoroughly
after handling. Close container after each use.
FIRST AID: If you experience diculty in breathing,
leave the area to obtain fresh air. If continued diculty is
experienced, get medical assistance immediately. In case of
eye contact, ush immediately with plenty of water for at
least 20 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, do not induce
vomiting. Call physician immediately. KEEP OUT OF REACH
OF CHILDREN - DO NOT TAKE INTERNALLY.
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2021 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 9/2021
1 of 1