Use and Care Manual

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 10/2019
PRODUCT INFORMATION
BEHR ® Fast-Drying Oil-Based Polyurethane is designed to provide a durable clear finish that protects and beautifies
interior wood surfaces. This product resists stains and scratches. Available in four sheens: Matte, Satin, Semi-Gloss and Gloss.
RECOMMENDED USES:
Ideal for properly prepared interior unfinished and finished surfaces such as furniture, moldings, cabinets, trim, wood and
doors.
PRODUCT SPECIFICATIONS:
Finish : B7116 Matte: 5-15 @ 60°
B7110 Satin: 20–30 @ 60°
B7112 Semi-Gloss: 50–60 @ 60°
B7114 Gloss: > 85 @ 60°
Resin Type: Polyurethane
Net Weight: 11.5 oz / 326 g
% Solids by Volume: % ± 2%
% Solids by Weight: % ± 2%
Max VOC (by weight): 67%
Max Product-Weighted MIR: 0.85
Coverage : 15-20 sq ft per can
APPLICATION:
To Touch: 2 hrs
Recoat: 2–4 hrs
Full Cure: 72 hrs
SURFACE PREPARATION:
FAST -DRY ING OIL - BASED POLYURETHANE AEROSOL
R
NO. B7110 SERIES
COMPLIES WITH THE BELOW AS OF 10 /1/2019
SCAQMD YES
AIM
YES
CARB SCM 2007 YES
CARB YES YES
OTC PHASE II YES
OTC
YES
LADCO
CAUTIONS/LIMITATIONS:
• Do not apply in direct sunlight or in temperatures below
55°F or above 90°F.
• Slight ambering may be experienced when Polyurethane is
applied over light-colored wood surfaces.
• Always spot test on an inconspicuous area to ensure
satisfactory result.
All surfaces must be clean, free of dust, oil, grease, wax,
polish , glue and all other foreign substances.
For refinishing, remove all wax or cleaner build-up with a wax
stripper or degreaser prior to sanding. Sand all surfaces in the
direction of the wood grain to desired smoothness. DO NOT
USE steel wool. Remove all dust from sanded surfaces with
tack cloth. If desired, apply BEHR® Wood Stain.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA vacuum
and a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National Lead
Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
• Wet overspray can be removed with mineral spirits.
• After each use, clear valve by holding can upside down and
spraying until only clear gas comes out.
• If spray button becomes clogged, wear eye protection,
wipe off button opening with lacquer thinner. Do NOT stick
pin in spray button opening.
• Wipe off tip before storing.
• Rags, steel wool and waste soaked with BEHR FAST DRYING
OIL-BASED POLYURETHANE may spontaneously catch fire if
improperly discarded or stored. To avoid a spontaneous
combustion fire immediately after use, place rags, steel wool
or waste in a sealed water-filled, metal container. Do not
store unused product inside the home. For disposal
guidance, contact your household refuse collection service,
fire department, county or state government control agency.
• Do not burn or place in home trash compactor.
GENERAL INFORMATION:
VENTILATION REQUIRED: To avoid inhalation and combustion
hazards (see below), DO NOT use this product unless you can
achieve cross ventilation by opening windows and doors
during application and drying. CONTAINS ACETONE,
PROPANE, NAPTHA, BUTANE AND PETROLEUM DISTILATES.
HARMFUL OR FATAL IF SWALLOWED. VAPOR HARMFUL.
May affect the brain or nervous system causing dizziness,
headache or nausea. CAUSES SERIOUS EYE IRRITATION.
IRRITATES SKIN, NOSE AND THROAT. Do not breathe vapors
or spray mist. If you experience eye watering, headaches or
dizziness, increase fresh air, wear respiratory protection
(NIOSH/MSHA TC 23C or equivalent) or leave the area. NOTICE:
Reports have associated repeated and prolonged occupational
overexposure to solvents with permanent brain and nervous
system damage. VAPORS MAY IGNITE EXPLOSIVELY. Do not
spray near sparks, heat or open flame. Do not smoke. Vapors
are heavier than air and can travel at floor level to distant
ignition sources. Extinguish all flames and pilot lights and turn
off stoves, heaters, electric motors, high intensity lights and
other sources of ignition during use and until all vapors are
gone. WARNING-CONTENTS UNDER PRESSURE. Do not
puncture or incinerate container. Do not expose to heat or
store at elevated temperatures above 120°F. Prolonged
exposure to sun may cause bursting. FIRST AID: If you have
difficulty breathing, leave area to obtain fresh air. If difficulty
continues, get medical attention immediately. If swallowed, do
not induce vomiting. Call physician immediately. In case of eye
contact, flush immediately with plenty of water for at least 20
minutes and get medical attention. For skin contact, wash
thoroughly with soap and water. CAUTION: KEEP OUT OF
REACH OF CHILDREN. DO NOT TAKE INTERNALLY.
Shake can vigorously for 1 minute after mixing ball begins
to rattle and often during use. Protect adjacent areas from
overspray. Hold can vertically 12 inches from surface.
Depress button fully and spray using an even, sweeping
motion with slightly overlapping strokes.
On unfinished wood, apply sufficient material to seal open
joints, edges and end-grain. Apply thin coats to avoid runs
and sags. Recoat within 1 hour. If unable to do so, wait a
minimum of 72 hours, then lightly sand and recoat.
Apply at least 3 coats on unfinished wood and 2 coats on
surfaces already finished. After final coat, allow at least 24
hours before normal use.
Dry Time: @ 77°F & 50% RH
Note: Dry times are based on good ventilation, temperature
of 77°F and 50% relative humidity. Lower temperature,
higher humidity, lack of air movement or application of thick
coats will extend drying times.