Use and Care Manual

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 10/2019
PRODUCT INFORMATION
BEHR ® Oil-Based Sp ar Urethane is designed to provide a durable clear protective finish for exterior and interior wood surfaces.
This product is fortified with UV inhibitors. Available in three sheens: Satin, Semi-Gloss and Gloss.
RECOMMENDED USES:
Ideal for properly prepared interior/exterior wood surfaces such as : furniture, doors and wood handrails.
PRODUCT SPECIFICATIONS:
Finish : Satin - 20–30 @ 60°
Semi-Gloss - 50–60 @ 60°
Gloss - 5> 85 @ 60°
Resin Type: Polyurethane
Weight per Gallon: 7.6–7.8 lb %
Solids by Volume: 42 % ± 2% %
Solids by Weight: 50 % ± 2%
VOC: < 450 g/L
Flash Point: > 100°F (38°C)
Viscosity: 50–70 KU
Recommended Film Thickness:
Wet: 3.2 mils / Dry: 1.3 mils @ 500 sq ft/gal per coat
For maximum durability, 3 coats are required.
Coverage: Up to 500 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
To Touch: 2 hrs
Sand or Recoat: 2–4 hrs
Light Use: 12–24 hrs
Full Cure: 3–4 days
SURFACE PREPARATION:
OI L - BASED SPAR URETHANE
R
NO. B7200 SERIES
COMPLIES WITH THE BELOW AS OF 10 /1/2019
SCAQMD NO
AIM
YES
CARB SCM 2007* YES
CARB*
YES YES
OTC PHASE II*
YES
OTC*
YES
LADCO*
CAUTIONS/LIMITATIONS:
• Do not apply in direct sunlight or in temperatures below
55°F or above 90°F.
• Shelf life under normal conditions is 2 years unopened.
• Contents are combustible. Keep away from heat and open
flame.
All surfaces must be clean, free of dust, oil, grease, wax,
polish , glue and all other foreign substances.
For refinishing, remove all wax or cleaner build-up with a wax
stripper or degreaser prior to sanding. Sand all surfaces in the
direction of the wood grain to desired smoothness. DO NOT
USE steel wool.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA vacuum
and a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National Lead
Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with mineral spirits or paint
thinner, where allowed. Otherwise, use acetone.
DANGER! Rags, steel wool and waste soaked with BEHR OIL-
BASED SPAR URETHANE may spontaneously catch fire if
improperly discarded or stored. To avoid a spontaneous
combustion fire, immediately after use, place rags, steel
wool or waste in a sealed water-filled, metal container. Do
not store unused product inside the home. For disposal
guidance, contact your household refuse collection service,
fire department, county or state government control
agency.
GENERAL INFORMATION:
DANGER! HARMFUL OR FATAL IF SWALLOWED.
COMBUSTIBLE LIQUID AND VAPOR. CONTAINS: PETROLEUM
DISTILLATES, XYLENE AND NAPHTHA, LIGHT AROMATIC. MAY
AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS,
HEADACHE OR NAUSEA. CAUSES EYE, SKIN, NOSE AND
THROAT IRRITATION. NOTICE: Reports have associated repeated
prolonged occupational exposure to solvents with permanent
brain damage. Intentional misuse by deliberately concentrating
and inhaling contents may be harmful or fatal. Keep away from
heat and flame. Do not smoke. Prevent build-up vapors by
opening all windows and doors to achieve cross-ventilation.
Extinguish all flames and pilot lights and turn off stoves, heaters,
electric motors, high intensity lights and other sources of ignition
during use and until all vapors are gone. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and spray
mist, open windows and doors or use other means to ensure fresh
air entry during application and drying. If you experience eye
watering, headaches or dizziness, increase fresh air. If properly
used, a respirator (NIOSH-approved for organic vapor with P series
particulate pre-filter) may offer additional protection; obtain
professional advice before using. A dust mask does not provide
protection against vapors. Avoid contact with eyes and skin. Wash
thoroughly after handling. Close container after each use. FIRST
AID: If you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experienced, get medical
assistance immediately. In case of eye contact, flush immediately
with plenty of water for at least 20 minutes and get medical
attention; for skin, wash thoroughly with soap and water. If
swallowed, do not induce vomiting. Call physician immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN-DO NOT TAKE
INTERNALLY.
Stir thoroughly prior to and during use. Do not shake or thin.
If wood stain color is desired, apply BEHR® Wood Stain. Using
a high quality natural bristle brush, dip approximately an
inch into the can, gently tapping it against the inside to
remove any excess. Apply a thin, even coat following the
direction of the grain making sure to maintain a wet edge.
To minimize the brush marks and bubbles after staining
application, tip off the surface by holding the brush at a 45°
angle and lightly run the bristles over the entire length of the
wood. Do not puddle, over-brush or overlap finishes. Sand
lightly between coats.
Brush: Natural Bristle brush
Roller: Lambswool cover
Thinning: DO NOT THIN
Dry Time: @ 77°F & 50% RH
Longer dry time may be required in cooler temperatures and
higher humidity.
Small Container Exemption compliant for quart containers.