Use and Care Manual

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 10/2019
PRODUCT INFORMATION
BEHR ® Water-Based Spar Urethane is designed to provide a durable crystal clear protective finish for exterior and interior
wood surfaces. This product is fortified with UV inhibitors. Available in three sheens: Satin, Semi-Gloss and Gloss.
RECOMMENDED USES:
Ideal for properly prepared Interior/Exterior wood surfaces exposed to direct sunlight. Ideal for residential applications, patio
furniture, doors and wood handrails. NOT RECOMMENDED for use on exterior wood siding, decks and stairs. CAUTION:
Topcoated surfaces may be slippery when wet.
PRODUCT SPECIFICATIONS:
Finish : B8200 Satin: 20–30 @ 60°
B8202 Semi-Gloss: 50–60 @ 60°
B8204 Gloss: 5> 85 @ 60°
Resin Type: Polyurethane/Acrylic
Weight per Gallon: 8.4–8.5 lb
% Solids by Volume: 25 % ± 2%
% Solids by Weight: 27 % ± 2%
VOC: < 275 g/L
Flash Point: N/A
Viscosity: 7–15 s (Zahn #3 Cup)
Recommended Film Thickness:
Wet: 3.2 mils / Dry: 0.8 mils @ 500 sq ft/gal per coat
For maximum durability, 3 coats are required.
Coverage: Up to 500 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
To Touch: 1 hr
Sand or Recoat: 1 hr
Light Use: 12–24 hrs
Full Cure: 3 days
SURFACE PREPARATION:
WATER - BASED SPAR URETHANE
R
NO. B8200 SERIES
COMPLIES WITH THE BELOW AS OF 10 /1/2019
SCAQMD NO
AIM
YES
CARB SCM 2007 YES
CARB
YES YES
OTC PHASE II
YES
OTC
YES
LADCO
• Do not apply in direct sunlight or in temperatures below
55°F or above 90°F.
• Do not use over painted surfaces, wax, shellac, fresh
lacquer or lacquer sanding sealer.
• Shelf life under normal conditions is 2 years unopened.
• Contents are combustible. Keep away from heat and
open flame.
All surfaces must be clean, free of dust, oil, grease, wax,
polish , glue and all other foreign substances.
For refinishing, remove all wax or cleaner build-up with a wax
stripper or degreaser prior to sanding. Sand all surfaces in the
direction of the wood grain to desired smoothness. DO NOT
USE steel wool. Remove all dust from sanded surfaces and
clean with tack cloth.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA vacuum
and a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National Lead
Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused produc in
accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
GENERAL INFORMATION:
CAUTION IRRITANT MAY CAUSE AN ALLERGIC SKIN
REACTION. CONTAINS: TRIETHYLAMINE, 2-BENZIMIDAZOLE
CARBAMIC ACID, METHYL ETHER, AND DIURON. AVOID
CONTACT WITH SKIN AND EYES AND AVOID BREATHING
VAPORS AND SPRAY MIST. WEAR EYE PROTECTION, GLOVES
AND PROTECTIVE CLOTHING. USE WITH ADEQUATE
VENTILATION. To avoid breathing vapors and spray mist, open
windows and doors or use other means to ensure fresh air entry
during application and drying. If you experience eye watering,
headaches or dizziness, increase fresh air. If properly used, a
respirator (NIOSH-approved for organic vapor with P series
particulate pre-filter) may offer additional protection; obtain
professional advice before using. A dust mask does not provide
protection against vapors. Avoid contact with eyes and skin. Wash
thoroughly after handling. Close container after each use. FIRST
AID: If you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experienced, get medical
assistance immediately. In case of eye contact, flush immediately
with plenty of water for at least 20 minutes and get medical
attention; if on skin, wash thoroughly with soap and water. If
swallowed, get medical attention immediately. CAUTION: KEEP
OUT OF REACH OF CHILDREN-DO NOT TAKE INTERNALLY.
Stir thoroughly prior to and during use. Do not shake or thin.
If wood stain color is desired, apply BEHR® Wood Stain. Using
a high quality nylon/polyester brush, dip approximately an
inch into the can, gently tapping it against the inside to
remove any excess. Apply a thin, even coat following the
direction of the grain making sure to maintain a wet edge. To
minimize the brush marks and bubbles after staining
application, tip off the surface by holding the brush at a 45°
angle and lightly run the bristles over the entire length of the
wood. Do not puddle, over-brush or overlap finishes. Sand
lightly between coats.
Brush: Nylon/Polyester brush
Thinning: DO NOT THIN
Dry Time: @ 77°F & 50% RH
Longer dry time may be required in cooler temperatures and
higher humidity.
CAUTIONS/LIM
ITATIONS: