User Manual 1002 Premium 10-Input 2-Bus Mixer with XENYX Preamps, British EQs and Optional Battery Operation
XENYX 1002B User Manual Table of Contents Thank you........................................................................ 2 Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited warranty............................................................. 3 1. Before you get started............................................... 4 1.1 Shipment...............................................................
XENYX 1002B User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
XENYX 1002B User Manual 1. Before you get started 1.3 Basic operation 1.1 Shipment The XENYX 1002B is easy to use. Simply follow these steps to achieve the best possible sound: Your XENYX 1002B was carefully packed at the factory and the packaging is designed to protect the unit from rough handling. Nevertheless, we recommend that you carefully examine the packaging and its contents for any signs of physical damage which may have occurred during transit.
XENYX 1002B User Manual 2. Audio Connections Balanced use with XLR connectors Unbalanced ¼" TS connector strain relief clamp 1 sleeve 2 3 tip input 1 = ground/shield 2 = hot (+ve) 3 = cold (-ve) 1 sleeve (ground/shield) 2 3 tip (signal) output For unbalanced use, pin 1 and pin 3 have to be bridged Fig. 2.3: ¼" Unbalanced Fig. 2.1: XLR Balanced Balanced ¼" TRS connector tip strain relief clamp sleeve ring tip tip sleeve shield sleeve Fig. 2.
XENYX 1002B User Manual 3. Controls and Connectors 3.1 Front panel (3) (7) (4) (5) (16) (15) (21) (17) (18) (1) (19) (2) (20) (22) (23) (6) (8) (9) (10) (24) (11) (25) (12) (26) (13) (14) (1) MIC – Plug a microphone into this input using an XLR cable. (2) LINE IN – Plug a line-level source into this jack using a ¼" TS or TRS cable. (3) INS(ERT) – Plug an external dynamic processor into this jack using a TRS to dual TS cable.
XENYX 1002B User Manual 3.2 Rear panel (28) (29) (28) AC POWER IN – Connect the mains power cable into this input. 4.1 Using external effects (29) POWER ON – Turns the mixer’s power on and off. The 1002B lets you use external effects processors to add a touch of reverb, delay, or other effects to various channels. Use the channel FX knobs, FX SEND knob and FX SEND jack to send a portion of the signal from several channels to an effects processor.
XENYX 1002B User Manual 4.2 Creating a monitor mix For live applications, audio engineers often send different mixes to the audience and to the performing musicians. To allow this, the 1002B is equipped with a dedicated monitor send bus. Each channel features a MON knob that sends a “pre-fader” signal to the MON OUT jack, allowing the channel’s volume fader to be adjusted without affecting the monitor mix. The signal can also be used as a second effects send.
XENYX 1002B User Manual DSP2024P HPS5000 B-1 B2031A XENYX1002B UCA222 Fig. 5.3: Computer Recording DSP2024P B-1 FCA202 HPS5000 XENYX1002B DV Deck Fig. 5.
XENYX 1002B User Manual 6. Specifications Mono Inputs CD/Tape In Microphone inputs (XENYX Mic preamp) Type XLR connector, electronically balanced, discrete input circuit Type RCA connector Impedance 10 k Ohms Max. input level +22 dBu Mic E.I.N.1 (20 Hz - 20 kHz) @ 0 Ω source resistance -134 dB 135.7 dB A-weighted Equalizer @ 50 Ω source resistance -131 dB 133.3 dB A-weighted LOW 50 Hz / ±15 dB @ 150 Ω source resistance -129 dB 130.
XENYX 1002B User Manual Main Mix System Data (Noise)3 Main mix @ -∞, channel fader @ -∞ -100 dB / -102.5 dB A weighted Main mix @ 0 dB, channel fader @ -∞ -82 dB / -85 dB A weighted Main mix @ 0 dB, channel fader @ 0 dB -72 dB / -75 dB A weighted Power Supply Power consumption 50 W Mains Voltage USA/Canada 120 V~, 60 Hz, Power Supply MXUL4 U.K.
We Hear You