EUROPOWER PMP1000/PMP3000/PMP5000 User Manual Version 1.
EUROPOWER PMP1000/PMP3000/PMP5000 IMPORTANT SAFETY INSTRUCTIONS 12) Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. 13) Only use attachments/accessories specified by the manufacturer. CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel.
EUROPOWER PMP1000/PMP3000/PMP5000 TABLE OF CONTENTS FOREWORD Dear Customer, Welcome to the team of EUROPOWER users and thank you very much for expressing your confidence in BEHRINGER products by purchasing this power mixer. 1 INTRODUCTION .........................................................
EUROPOWER PMP1000/PMP3000/PMP5000 1.1.2 Initial operation 1 INTRODUCTION Congratulations! With the PMP1000/PMP3000/PMP5000 you have acquired a state-of-the-art power mixer that sets new standards. Right from the very start it has been our goal to design a revolutionary unit that can be used for a wide variety of applications. Indeed, this overwhelming power mixer gives you plenty of functionality and a broad range of connection and expansion options.
EUROPOWER PMP1000/PMP3000/PMP5000 PMP3000/PMP5000: When you press the PFL button (Pre Fader Listening) the left LED shows the pre-fader input gain of the channel. Adjust the optimum input gain (0 . When PFL is on, the corresdB) with the TRIM control ponding LED illuminates. 2 CONTROL ELEMENTS A detailed description of all functions of your power mixer can be found in the following chapters. Please also refer to the enclosed sheet with the numbered illustrations to get a good overview of the control layout.
EUROPOWER PMP1000/PMP3000/PMP5000 PMP1000: Channels 13/14 and 15/16 are routed to the main mix without additional tone or volume adjustment. For example, using the channels 13/14 and 15/16 you can connect a submixer and utilize the PMP1000’s power amplifier. PMP3000: The stereo channels 9/10 and 11/12 are equipped with additional RCA connectors. PMP5000: The stereo channels 13/14 and 15/16 are equipped with additional RCA connectors.
EUROPOWER PMP1000/PMP3000/PMP5000 2.4 Main and monitor section The SURROUND control determines the effect intensity. This is a built-in effect, which widens the stereo panorama, thus making the sound more lively and transparent. 2.3 Effects section List of all multi-effects processor presets. Press the XPQ TO MAIN switch to activate this effect. The LED level meter on the effects module should always show a sufficiently high level. Make sure that the Clip LED illuminates with signal peaks only.
EUROPOWER PMP1000/PMP3000/PMP5000 The FX SEND connector can be used to route the FX SEND signal from the input channel, for example, to the input of an external effects device. Since the PMP5000 ), both FX has two FX controls per input signal (see SEND 1+2 are present at one jack. 2.4.1 Connectors Use the CD/TAPE INPUT jacks (RCA) to connect an external stereo signal, such as a CD player, tape deck or other line-level sources.
EUROPOWER PMP1000/PMP3000/PMP5000 4 INSTALLATION 4.1 Mains connection The mains connection is made using the enclosed power cord and a standard IEC receptacle. It meets all of the international safety certification requirements. Blown fuses must be replaced by fuses of the same type and rating. Please make sure that all units have a proper ground connection. For your own safety, never remove or disable the ground conductor from the unit or of the AC power cord. Fig. 4.3: XLR connectors 4.
EUROPOWER PMP1000/PMP3000/PMP5000 4.3 Loudspeaker connections Your power mixer is equipped with high-quality loudspeaker connectors (compatible to Neutrik® Speakon®), which ensure safe and trouble-free operation. The Speakon® connector was especially developed for high-power loudspeakers. Once it is plugged in, it safely locks into position and cannot be accidentally disengaged. It prevents the occurrence of electrical shock and ensures the correct polarity.
EUROPOWER PMP1000/PMP3000/PMP5000 5 WIRING EXAMPLES Fig. 5.2: Bridged mono operation Fig. 5.1: Stereo operation must be set For stereo operation the POWER AMP switch to its upper position (MAIN or MAIN L/MAIN R). Outputs A and B provide the stereo main signal for passive speakers. The preamp monitor output is connected to two parallel active speakers, which are used as on-stage monitors. Use the footswitch to enable/disable the effects processor.
EUROPOWER PMP1000/PMP3000/PMP5000 Fig. 5.3: Dual mono operation must For a dual mono operation, the AMP MODE switch be set to its center position (MON1/MONO for PMP3000/PMP5000 or MON for PMP1000)! The two loudspeaker outputs provide the main and the monitor signals, separately from each another. Each of these signals is then sent to two speakers wired in parallel. 12 Fig. 5.
EUROPOWER PMP1000/PMP3000/PMP5000 Fig. 5.5: Expanded set-up This application is an expanded set-up based on the standard set-up as shown in fig. 5.4, and provides additional connection options. Again, this is just an example, which can be expanded in various ways.
EUROPOWER PMP1000/PMP3000/PMP5000 6 SPECIFICATIONS PMP1000 PMP3000 MICROPHONE INPUTS Type Mic E.I.N. (20 Hz - 20 kHz) @ 0 Ω source resistance @ 50 Ω source resistance @ 150 Ω source resistance XLR, electronically balanced, discrete input circuit -134 dB / 136 dB A-weighted -131.5 dB / 134 dB A-weighted -129 dB / 131 dB A-weighted < 10 Hz - 155 kHz (-1 dB) < 10 Hz - > 200 kHz (-3 dB) +10 dB, +60 dB +12 dBu @ +10 dB gain approx. 2.6 kΩ balanced / 1.
EUROPOWER PMP1000/PMP3000/PMP5000 PMP1000 PMP3000 PMP5000 DSP 24-Bit Delta-Sigma, 64/128-times oversampling 90 dB 46.875 kHz max. 5 s approx. 1.
EUROPOWER PMP1000/PMP3000/PMP5000 7 WARRANTY § 1 OTHER WARRANTY RIGHTS AND NATIONAL LAW 1. This warranty does not exclude or limit the buyer’s statutory rights provided by national law, in particular, any such rights against the seller that arise from a legally effective purchase contract. 2. The warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law. 2.
EUROPOWER PMP1000/PMP3000/PMP5000 FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION Responsible party name: BEHRINGER USA, Inc. Address: 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA Phone/Fax No.
