Quick Start Guide XENYX CONTROL2USB High-End Studio Control and Communication Center with VCA Control and USB Audio Interface
XENYX CONTROL2USB Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
4 XENYX CONTROL2USB Consignes de sécurité Les points repérés par ce symbole portent une tension électrique suffisante pour constituer un risque d’électrocution. Utilisez uniquement des câbles d’enceintes professionnels de haute qualité avec fiches Jack mono 6,35 mm ou fiches à verrouillages déjà installées. Toute autre installation ou modification doit être effectuée uniquement par un personnel qualifié.
6 XENYX CONTROL2USB Instruções de Segurança Importantes Aviso! Terminais marcados com o símbolo carregam corrente elétrica de magnitude suficiente para constituir um risco de choque elétrico. Use apenas cabos de alto-falantes de alta qualidade com plugues TS de ¼" ou plugues com trava de torção pré-instalados. Todas as outras instalações e modificações devem ser efetuadas por pessoas qualificadas.
8 XENYX CONTROL2USB 9 Quick Start Guide XENYX CONTROL2USB Hook-up (EN) Step 1: Hook-Up (ES) Paso 1: Conexión (FR) Etape 1: Connexions HPM1000 (DE) Schritt 1: Verkabelung HPS3000 HPS3000 HPS5000 POWERPLAY PRO-8 HA8000 Headphone distribution amp (PT) Passo 1: Conexões Laptop Keyboard BEHRINGER A500 Reference amplifier BEHRITONE Footswitch BEHRITONE C50A Active studio monitors Record player TRUTH B3031A Active studio monitors HPS3000 TRUTH B2031P Passive studio monitors
10 XENYX CONTROL2USB 11 Quick Start Guide XENYX CONTROL2USB Controls (1) (2) (3) (EN) Step 2: Controls (4) (16) (5) (6) (17) (15) (14) (13) (12) (18) (10) (9) (11) (8) (34) (24) (23) (33) (30) (20) (29) (28) (27) (21) (22) SOURCE SELECT buttons determine which input source will be routed to outputs on the back panel. (20) STUDIO OUT trim knob adjusts the signal sent via the STUDIO OUT jacks.
12 XENYX CONTROL2USB 13 Quick Start Guide XENYX CONTROL2USB Controls (ES) Paso 2: Controles (1) Los botones SOURCE SELECT determina qué fuente de entrada será rutada a las salidas del panel trasero. (20) El mando de retoque STUDIO OUT le permite ajustar la señal emitida a través de las tomas STUDIO OUT. (2) Los MEDIDORES DE NIVEL le muestra la fuerza de la señal de entrada o salida de la fuente stereo activa conectada.
14 XENYX CONTROL2USB 15 Quick Start Guide XENYX CONTROL2USB Controls (DE) Schritt 2: Botões SOURCE SELECT determinam qual fonte de entrada será roteada às saídas no painel traseiro. (21) O botão de controle trim ajusta a sensibilidade da entrada do sinal de entrada em ±10 dB (o mesmo nas ENTRADAS 2, 3 e 4). TRIM-Regler steuert die Eingangsempfindlichkeit des eingehenden Signals um +/-10 dB (auch bei den INPUTS 2, 3 und 4 verfügbar).
16 XENYX CONTROL2USB 17 Quick Start Guide XENYX CONTROL2USB Getting started (EN) Step 3: Getting Push the Power button on the rear panel to the OFF position (pushed out). started Turn the volume and all level knobs (top and rear panel) to the far left position. Push all SOURCE SELECT, MONITOR SELECT, and routing switches to the out position. Connect the included power cable to the input on the back panel.
18 XENYX CONTROL2USB 19 Quick Start Guide XENYX CONTROL2USB Puesta en marcha (ES) Paso 3: Puesta en marcha Coloque el interruptor Power del panel trasero en la posición OFF (no pulsado). Coloque los mandos de volumen y todos los de nivel (panel superior y trasero) en su tope izquierdo. Coloque todos los interruptores SOURCE SELECT, MONITOR SELECT y de ruteo en la posición de “no pulsado”. Conecte el cable de alimentación incluido en la entrada de corriente del panel trasero.
20 XENYX CONTROL2USB 21 Quick Start Guide XENYX CONTROL2USB Mise en oeuvre (FR) Etape 3 : Mise en oeuvre Appuyez sur l’interrupteur Power à l’arrière pour le placer en position haute OFF. Réglez le Volume et tous les niveaux (faces supérieure et arrière) au minimum. Relâchez toutes les touches SOURCE SELECT, MONITOR SELECT, et de routage. Reliez le cordon secteur fourni à son embase, en face arrière.
22 XENYX CONTROL2USB 23 Quick Start Guide XENYX CONTROL2USB Erste Schritte (DE) Schritt 3: Erste Schritte Lösen Sie die rückseitige Power-Taste (OFF). Drehen Sie den VOLUME- und alle Pegel-Regler (Ober- und Rückseite) ganz nach links. Lösen Sie alle SOURCE SELECT-, MONITOR SELECT- und Routing-Tasten. Verbinden Sie das mitgelieferte Netzkabel mit dem rückseitigen Netzanschluss. Verbinden Sie die Audio-Ausgänge Ihres DAW (Digital Audio Workstation) Audio-Interfaces mit den MONITOR MIX INPUT-Buchsen.
24 XENYX CONTROL2USB 25 Quick Start Guide XENYX CONTROL2USB Primeiros Passos (PT) Passo 3: Primeiros Coloque o botão power no painel traseiro na posição desligada OFF (para fora). Passos Gire o botão de volume e todos os botões de nível (painel superior e traseiro) para a posição mais à esquerda possível. Empurre todas as seleções de fonte SOURCE SELECT, de monitor MONITOR SELECT, e botões de roteamento para a posição puxada para fora.
+4 -10 LINE PHONO IN 3 IN 4 TALK BACK Automatic Gain Control INTERNAL TALKBACK MIC AGC MIN...MAX off off MONITOR SOURCE 4 SOURCE SELECT off 3/USB 2 1 off TO 2-TRACK TO PHONES/ STUDIO off off LR INPUT BUS PHONES/ STUDIO BUS PHONES/STUDIO -10...+10 -10...+10 -10...+10 -10...+10 triggers both switches simultaneously TALKBACK FOOTSWITCH +4 -10 +4 -10 IN 2 MONITOR MIX INPUT +4 -10 IN 1 LR MIN...MAX MIN...MAX off +4 -10 MIN...MAX -10...
28 XENYX CONTROL2USB Quick Start Guide Specifications Frequency Response Line-level inputs and outputs ¼" jack, balanced or unbalanced Phono input Input/Output VU Meters 12-segment LED 10 Hz to 40 kHz (+0 dB / -1 dB) 20 Hz to 20 kHz (±1 dB) Distortion (THD & IMD) Line-level inputs to line-level outputs (unity gain) Phono input <0.02 %, 20 Hz to 20 kHz @ +4 dBu <0.
30 XENYX CONTROL2USB Quick Start Guide FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION Other important information Important information XENYX CONTROL2USB Responsible Party Name: MUSIC Group Services NV Inc.
We Hear You
