User manual
34
ULTRADRIVE PRO DCX2496
7. SPECIFICATIONS
The preset 5.1FRONT has been optimized for the L-C-R front
speakers with 2 speaker ways each (see also chapter 5.3). The
three signals required Front-Left, Front-Center, Front-Right are
routed via the three inputs (A, B, C) to the first DCX2496.
On the second DCX2496, the preset 5.1 REAR should be used
as a starting point. It supplies the two rear surround speakers
(also 2-way systems) plus the monophonic sub-bass channel
(LFE = Low Frequency Enhanced) with the input signals Rear-
Left, Rear-Right and Sub-bass, using connectors In A, B, C. The
sixth output of the second ULTRADRIVEPRO is not used in this
application, but is left available for additional effects or as a mono
delay line.
7. SPECIFICATIONS
ANALOG INPUTS (A, B, C)
Type electronically balanced
Connector XLR
Max. input level +22 dBu
Input impedance approx. 20 kΩ at 1 kHz
Crosstalk -72 dB @ 0 dBu In
DIGITAL INPUT (A)
Connector XLR
Format S/PDIF or AES/EBU
Input level 0.3 to 10 Vpp
Input impedance approx. 110 Ω
Sampling frequency 32 to 96 kHz
Special feature Sample Rate Converter
MICROPHONE INPUT (C)
Type electronically balanced
Connector XLR
Max. input level -23 dBu
Input impedance approx. 470 Ω at 1 kHz
Phantom supply +15 V
ANALOG OUTPUTS (1, 2, 3, 4, 5, 6)
Type electronically balanced
Connector XLR
Max. output level +22 dBu
Output impedance approx. 160 Ω at 1 kHz
Crosstalk -100 dB @ 10 dBu In
SYSTEM DATA
Sampling frequency 96 kHz
Signal delay < 1 ms
Analog input to analog output
Frequency response 10 Hz to 35 kHz (-1 dB) typ.
Dynamic range 109 dB
(analog input ß analog output)
Input noise -90 dBu (@ +22 dBu ß 112 dB)
Output noise -90 dBu (@ +22 dBu ß 112 dB)
THD+N Ratio 0,007 % @ 0 dBu In, Gain 1
0,004 % @ 10 dBu In, Gain 1
CONVERTERS
A/D converter
Resolution 24-Bit Delta-Sigma AKM
®
Oversampling 64x
Dynamic range 112 dB typ.
D/A converter
Resolution 24-Bit Delta-Sigma AKM
®
Oversampling 64x
Dynamic range 112 dB typ.
SERIAL INTERFACE
RS-232
Type 9-pin sub-D connector
Transmission type 115200 bauds, 8 data bits,
1 stop bit, no parity
RS-485 (2x)
Type RJ-45 connector
Transmission type 115200 bauds, 8 data bits,
1 stop bit, no parity
POWER SUPPLY
Mains voltage
USA/Canada 120 V~, 60 Hz
Europe/U.K./Australia 230 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
General export model 100 - 240 V~, 50 - 60 Hz
Power consumption approx. 12 W
Fuse 100 to 240 V~: T 1 A H
Mains connector Standard IEC receptacle
DIMENSIONS (H x W x D) 1 ¾" (44.5 mm) x 19" (482.6 mm)
x 8 ½" (217 mm)
WEIGHT approx. 3 kg
SHIPPING WEIGHT approx. 4.2 kg
BEHRINGER makes every effort to ensure the highest standard of quality. Necessary
modifications are carried out without notice. Thus, the specifications and design of the
device may differ from the information given in this manual.