Calibration

ManualsBrandsBehringer ManualsSynthesizersDeepMind 12D

Synthesizers and Samplers

DEEPMIND 12D

True Analog 12-Voice Polyphonic Desktop

Synthesizer with 4 FX Engines, 2 OSCs and

LFOs per Voice, 3 ADSR Generators, 8-Channel

Modulation Matrix, 32-Step Control Sequencer,

Tablet Remote Control and Built-In Wi

985-40000-01100 Rev.A

2021-02-03

page 1 of 5

Condential, for internal use only. Not to be reproduced.

User Support Bulletin

Calibration Procedure

Selected parameters are adjusted using the -/NO or +/YES switches, the rotary knob or the DATA ENTRY fader. The

rotary knob has a click which allows very accurate control. The fader allows rapid adjustment across the full range.

To navigate the options in the CALIBRATION menu, use the BANK/UP or BANK/DOWN switches.

The CALIBRATION menu in the SYSTEM SETTINGS menu allows you to perform CALIBRATION of the VOICES and PEDAL INPUT.

Follow all steps in the order in which they are presented.

In order to start a calibration routine, make sure that the '<' symbol on the appropriate CALIBRATE line is highlighted,

and then press the +/YES switch.

Calibration Menu

Introduction

The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes,

then the following recalibration procedures will help bring it back to its factory settings.

Summary of content (5 pages)

PAGE 1
Synthesizers and Samplers DEEPMIND 12D True Analog 12-Voice Polyphonic Desktop Synthesizer with 4 FX Engines, 2 OSCs and LFOs per Voice, 3 ADSR Generators, 8-Channel Modulation Matrix, 32-Step Control Sequencer, Tablet Remote Control and Built-In Wifi User Support Bulletin Introduction The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes, then the following recalibration procedures will help bring it back to its factory settings.
PAGE 2
Synthesizers and Samplers DEEPMIND 12D The DeepMind 12D has 12 voices. Each voice has its own LFO, OSC, VCF, ENV and VCA stages. The CALIBRATION routine is used for Voice checking, OSC wave shapes, VCF self-oscillation, Pulse Width modulation and the VCA bias. VCF - Unlike many other synthesizers, the DeepMind 12D is capable of accurate pitch tracking even when the filter resonance is pushed to (and past) the point where the filter starts to self-oscillate.
PAGE 3
Synthesizers and Samplers DEEPMIND 12D To start the calibration routine, please follow the procedure below: In order to start the calibration routine, make sure that the '<' symbol is on the appropriate CALIBRATE line and highlighted, and press the +/YES switch. NOTE: The calibration run time is shown on the bottom of the screen so that you can plan your work around any of the calibration phases. The calibration routine will then start. Throughout the tests you will see various waveforms being played.
PAGE 4
Synthesizers and Samplers DEEPMIND 12D CALIBRATE PEDAL To calibrate the PEDAL please use the following process: NOTE: During the calibration the GLOBAL, -/NO and +/YES switches will be flashing. If at any time you want to cancel the calibration routine, you can press the -/NO switch. No previous calibration data will be changed if you do cancel the routine. To confirm the calibration at each stage press +/YES as described below.
PAGE 5
Synthesizers and Samplers DEEPMIND 12D NOTE: To cancel the routine, press the -/NO switch, and you will see the following message: To confirm the CALIBRATION of the PEDAL input, press the +/YES switch: The calibration data will then be stored for the PEDAL and you will be returned to the CALIBRATE menu. From here you can perform another calibration from the menu, or press the GLOBAL switch again to return to the SYSTEM SETTINGS menu.