User Manual EURORACK UB1204 -PRO Ultra-Low Noise Design 12-Input 2/2-Bus Mixer with Premium Mic Preamplifiers and Multi-FX Processor UB1204-PRO Ultra-Low Noise Design 12-Input 2/2-Bus Mic/Line Mixer with Premium Mic Preamplifiers
EURORACK UB1204FX-PRO/UB1204-PRO User Manual Table of Contents Thank you........................................................................ 2 Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited warranty............................................................. 3 1. Introduction................................................................ 4 1.1 General mixing console functions ..........
EURORACK UB1204FX-PRO/UB1204-PRO User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual 1. Introduction 1.2 The user’s manual The BEHRINGER EURORACK mixing console offers you premium-quality microphone preamplifiers with optional phantom power supply, balanced line inputs and the ability to connect external effects devices. Because of its extensive and carefully thought-out routing possibilities, your EURORACK lends itself equally to both live and studio use.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual 2. Control Elements and Connectors 2.1.2 Equalizer This chapter describes the various control elements of your mixing console. All controls, switches and connectors will be discussed in detail. 2.1 Mono channels 2.1.1 Microphone and line inputs Fig. 2.2: The equalizer of the input channels All mono input channels include a 3-band equalizer. All bands provide boost or cut of up to 15 dB. In the central position, the equalizer is inactive.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual PRE SOLO When the PRE switch is pressed, aux send 1 is sourced pre-fader. The SOLO switch (UB1204FX-PRO only) is used to route the channel signal to the solo bus (Solo In Place) or to the PFL bus (Pre Fader Listen). This enables you to monitor a channel signal without affecting the main output signal. The signal you hear is sourced either before (PFL, mono) or after (solo, stereo) both the pan control and the channel fader (see chapter 2.3.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual 2.3 Connector panel and main section AUX SEND 2 Whereas it was useful to trace the signal flow from top to bottom in order to gain an understanding of the channel strips, we now look at the mixing console from left to right. The signals are, so to speak, collected from the same point on each of the channel strips and then routed to the main section all together.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual STEREO AUX RETURN MON 2.3.6 Level meter and monitoring The STEREO AUX RETURN MON control has a special function: it can be used to add an effect to a monitor mix. For example: Monitor mix with effect In this instance, the effects device should be set up as follows: AUX SEND 2 is connected to the L/Mono input of your effects device, while its outputs are connected to STEREO AUX RETURN 1. Connect the amplifier of your monitor system to AUX SEND 1.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual LEVEL METER PFL (UB1204FX-PRO only) The high-precision level meter accurately displays the appropriate signal level. The PFL LED indicates that the peak meter is set to PFL mode. LEVEL SETTING: PHONES When recording to a digital device, the recorder’s peak meter should not exceed 0 dB. This is because, unlike analog recordings, slightly excessive levels can create unpleasant digital distortion. You can connect headphones to this 1/4" TRS connector.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual ALT 3-4 OUTPUTS 3. Digital Effects Processor The ALT 3-4 outputs are unbalanced and carry the signals of the channels that you have assigned to this group using the MUTE switch. This can be used to route a subgroup to a further mixing console for example, or or it could be used as a recording output working in tandem with the main output. This means you could record to four tracks simultaneously.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual 4. Installation 4.2.1 Audio connections 4.1 Rack mounting Please use commercial RCA cables to wire the 2-track inputs and outputs. The packaging of your mixing console contains two 19" rack mount wings which can be installed on the side panels of the console. Before you can attach the rack mount wings to the mixing console, you need to remove the screws holding the left and right side panels.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual Balanced ¼" TRS connector strain relief clamp sleeve ring tip 5. Specifications Mono Inputs Microphone Inputs (IMP “Invisible” Mic Preamp) Type sleeve ground/shield ring cold (-ve) tip hot (+ve) For connection of balanced and unbalanced plugs, ring and sleeve have to be bridged at the stereo plug. Fig. 4.4: 1/4" TRS connector ¼" TRS headphones connector strain relief clamp sleeve ring tip sleeve ground/shield Mic E.I.N.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual EQ Mono Channels Main Mix System Data2 Low 80 Hz / ±15 dB Mid 2.5 kHz / ±15 dB High 12 kHz / ±15 dB EQ Stereo Channels Low 80 Hz / ±15 dB Mid 2.5 kHz / ±15 dB High 12 kHz / ±15 dB Aux Sends Type 1/4" TS connector, unbalanced Impedance approx. 120 Ω Max.
EURORACK UB1204FX-PRO/UB1204-PRO User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION EURORACK UB1204FX-PRO/ UB1204-PRO Responsible Party Name: MUSIC Group Services US Inc.
We Hear You