User's Manual

11 EURORACK UB2442FX-PRO/UB2222FX-PRO/UB1832FX-PRO/UB1622FX-PRO User Manual
STEREO AUX RETURN 1/2 (TO AUX SEND)
The two right-hand STEREO AUX RETURN controls have a special function:
they can be used to add an eect to a monitor mix. An example follows
(UB1622FX-PRO wired to an eects device):
Monitor mix with eect
In this instance, your eects device should be set up as follows: the AUX SEND 2
jack should be connected to the L/Mono input of your eects device, with its
outputs coming back into the STEREO AUX RETURN 1 jacks.
Connect the AUX SEND 1 jack output to the amplier of your monitor system.
The AUX SEND 1 master control determines the overall volume of the
monitor mix.
Using the STEREO AUX RETURN (TO AUX SEND) control, the eect signal can now
be blended into the monitor mix.
You can easily use the headphones distribution amplier BEHRINGER POWERPLAY
PRO HA4700/HA8000 to provide four (HA8000: eight) stereo headphone mixes for
your studio.
The following table shows which jacks on the console can be used
for this purpose.
External eects
device receives
signal from...
Extenal eects
device routes
signal back to...
The eect signal
reaches the
monitor mix via...
UB1622FX-PRO
AUX SEND 2
STEREO AUX RETURN 1
Connectors
STEREO AUX RETURN 1
(TO AUX SEND 1) Control
UB1832FX-PRO
AUX SEND 1
STEREO AUX RETURN 2
Connectors
MONITOR Switch of the
FX/AUX 2 RET
UB2222FX-PRO
AUX SEND 2
STEREO AUX RETURN
Connectors 1 or 2
STEREO AUX RETURN 1
(TO AUX SEND 1) Control
UB2442FX-PRO
AUX SEND 2
STEREO AUX RETURN 1
Connectors
STEREO AUX RETURN 1
(TO AUX SEND 1) Control
:
Optional
AUX SEND 1
STEREO AUX RETURN 2
Connectors
STEREO AUX RETURN 2
(TO AUX SEND 2) Control
Tab. 2.1: Connectors and controls for monitor mix with eect
STEREO AUX RETURN FX
On consoles UB1622FX-PRO and UB1832FX-PRO this is the STEREO AUX
RETURN 2, on consoles UB2222FX-PRO and UB2442FX-PRO this is the
STEREO AUX RETURN 3.
Use the STEREO AUX RETURN FX control to determine the level of the signal
routed from the AUX RETURN FX jacks to the main mix. If nothing is connected to
these jacks, the output of the built-in eects module will appear.
MAIN MIX / TO SUBS
This switch routes the signal fed in via the STEREO AUX RETURN FX jacks either to
the main mix (not pressed) or to the submix (pressed).
On the UB2442FX-PRO you can select which subgroup the signal is assigned to
(switches 1-2 / 3-4, to the right of MAIN MIX / TO SUBS).
SOLO RETURNS
Additionally, this model allows you to route the aux returns together to the solo
bus and the PFL bus. The LED lights up when Solo is on.
STEREO AUX RETURN 4 (UB2442FX-PRO only)
This control behaves the same way as the other stereo aux returns.
Additionally, it provides for a simple monitor path using the switch PHONES/CTRL
ROOM ONLY.
PHONES/CTRL ROOM ONLY
Use this switch to route the signal appearing at the AUX RETURN 4 jacks to the
control room and headphones outputs.
2.3.6 Supplement to UB1832FX-PRO
The UB1832FX-PRO has a stereo fader for the AUX RETURN FX and oers a variety
of routing options: MUTE disables the eect return (but not PFL of course!),
SOLO routes it to the Solo or PFL busses, SUB to the subgroups and MAIN to the
main mix.
UB1832FX-PRO
Fig. 2.13: The FX/AUX 2 return fader of the UB1832FX-PRO
MON
The MON switch routes the signals appearing at the AUX RETURN2 jacks to the
monitor path, along with the monitor signals from the channels.
If you wish to route the eect signal to the monitor mix, you can also switch aux
1 to pre-fader, drive the eect device from the aux 1 output and return the eect
signal via AUX RETURN 2 to the monitor signal.