User Manual EUROPOWER PMP1680S/PMP980S/PMP960M 1600/900-Watt 10/6-Channel Powered Mixer with Dual Multi-FX Processor and FBQ Feedback Detection System
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual Table of Contents Thank you........................................................................ 2 Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited warranty............................................................. 3 1. Before you get Started............................................... 4 1.1 Shipment........................................
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual 1. Before you get Started 1.3 Online registration 1.1 Shipment Please register your new BEHRINGER equipment right after your purchase by visiting http://behringer.com and read the terms and conditions of our warranty carefully. Your PMP mixer was carefully packed at the factory and the packaging is designed to protect the unit from rough handling.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual Front Panel (16) (1) (1) (2) (2) (3) (3) (4) (4) (5) (5) (21) (20) (19) (24) (14) (27) (15) (23) (28) (18) (29) (6) (7) (8) (8) (17) (30) (34) (9) (10) (11) (13) (12) (12) (21) (36) (20) (22) (25) (26) (32) (40) (31) (33) Rear Panel (44) (43) (41) (42) (45) (35) (37) (38) (39)
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual 2. Control Elements A detailed description of all functions of your power mixer can be found in the following chapters. Please also refer to the enclosed sheet with the numbered illustrations to get an overview of the control layout. 2.1 Mono and stereo channels (1) The HIGH control in the EQ section governs the high-frequency range of the respective channel. (2) Use the MID control to boost or cut the mid-range frequencies.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual ◊ In BRIDGE mode, always connect only one loudspeaker with an impedance of at least 8 Ω to OUTPUT B (pins 1+/2+)! Please note that OUTPUT A must NEVER be used in BRIDGE mode (with pin connections 1+/2+)! ◊ In all other operating modes, the minimum impedance of the speaker connected must not fall below 4 Ω. (29) Use the SPEAKER PROCESSING switch to activate a filter that adapts the mixer to the specifications of your loudspeakers.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual 3. Digital Effects Processor Balanced ¼" TRS connector 24-BIT MULTI-EFFECTS PROCESSOR strain relief clamp This built-in effects module produces high-grade standard effects such as reverb, chorus, flanger, delay and various combination effects. The integrated effects module has the advantage of requiring no wiring. This way, the danger of creating ground loops or uneven signal levels is eliminated at the outset, completely simplifying the handling.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual ◊ Please use a dual footswitch for the PMP980S/PMP1680S, so that you can enable/disable FX 1 and FX 2 independently of each other. In this case, the tip of the ¼" plug controls FX 1, and the ring FX 2. tip tip sleeve shield sleeve Fig. 4.5: RCA cable Please be sure to only use professional locking-style speaker cables (type NL4FC). Please check the pin connections of your loudspeakers and cables depending on the EUROPOWER speaker output you choose.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual 5. Wiring Examples For stereo operation the POWER AMP switch (28) of the PMP980S/PMP1680S must be set to its upper position (MAIN L/MAIN R). Outputs A and B deliver the stereo main signal to the P.A. speakers. Two active speakers, wired in parallel, are connected to the preamp monitor output. They are used as on-stage monitor speakers. The effects processors can be switched on and off with a dual footswitch.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual This illustration shows just one example of how the channels of your power mixer can be used, including the connection of mono and stereo sources, and the tape ins and outs recording the mix signal or playing back external signals. EUROPOWER PMP1680S One example of how to use your power mixer with a subwoofer in bridged mono mode. The illustration shows the PMP1680S with a subwoofer connected to OUTPUT B that will receive the full (bridged) output power.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual 6. Specifications Microphone Inputs Type Preamp Outputs XLR, electronically balanced input circuit Mic E.I.N. (20 Hz - 20 kHz) MAIN Type ¼" TS connectors, unbalanced @ 0 Ohm source resistance -112 dB / 114 dB A-weighted Impedance approx. 150 Ohm, unbalanced @ 50 Ohm source resistance -112 dB / 114 dB A-weighted Max.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual DSP Fuses Converter 24-bit Delta-Sigma, 64/128-times oversampling Dynamics D/A 90 dB Sampling rate 40 kHz Delay Time max. 5 secs Signal run time (Line In > Line Out) approx. 1.5 ms Display 2-digit, 7-segment LED PMP980S/PMP1680S Type 2 x 2-digit, 7-segment LED Power Consumption Power consumption 1000 W Mains connector IEC standard receptacle Dimensions (H x W x D) approx. 315 x 460 x 220 mm (approx.
EUROPOWER PMP1680S/PMP980S/PMP960M User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION EUROPOWER PMP1680S/PMP980S/PMP960M Responsible Party Name: MUSIC Group Services US Inc.
We Hear You