User Manual EUROPOWER EP4000/EP2000 Professional 4,000 and 2,000-Watt Stereo Power Amplifier with ATR (Accelerated Transient Response) Technology
EUROPOWER EP4000/EP2000 User Manual Table of Contents Thank you........................................................................ 2 Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited Warranty............................................................ 3 1. Introduction................................................................ 5 1.1 Before you get started...............................
EUROPOWER EP4000/EP2000 User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
EUROPOWER EP4000/EP2000 User Manual “Support” at behringer.com. If your country is not listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at behringer.com. Alternatively, please submit an online warranty claim at behringer.com BEFORE returning the product. All inquiries must be accompanied by a description of the problem and the serial number of the product.
EUROPOWER EP4000/EP2000 User Manual 1. Introduction ◊ Please make sure that all units have a proper ground connection. Honestly, who really likes to read manuals? We know you want to get started right away, but please read this manual carefully and keep it for future reference. It is only after reading these instructions that you will fully understand and be able to use all the features your EUROPOWER amplifier has to offer. 1.
EUROPOWER EP4000/EP2000 User Manual 2.2 Rear panel (7) (8) (9) (11) (12) (13) (10) (14) (16) (15) Fig. 2.2: Rear panel control elements (7) These are the balanced XLR inputs (channels 1 and 2). 2.3 Configuration switches (MODE SWITCHES) (8) These are the stereo ¼" TRS inputs (channels 1 and 2). They can also be used with unbalanced plugs. (9) These are the MODE switches, used to alter the operating modes as well as to set the limiters and high-pass filters (see chapter 2.3).
EUROPOWER EP4000/EP2000 User Manual The 50 Hz filter should be engaged when using broadband speakers because the filter provides a moderate amplification in the 100-Hz range, resulting in a fuller sound. The 30 Hz filter is ideally suited for subwoofer operation as well as for broadband cabinets. The “Off” setting should be used only for special applications (e.g. studio applications), in which recognizing and subsequently removing infra-sound is important. 2.3.
EUROPOWER EP4000/EP2000 User Manual Fig. 3.2: DIP switch positions for 2-channel operation Fig. 3.4: DIP switch positions for parallel operation Parallel mode is identical to 2-channel mode, except for the inputs of both channels are internally connected in parallel. One input signal routes parallel both channels, while their filters etc. are independently controlled. When running in mono-bridged mode, the voltage of both channels is added up and fed into a single loudspeaker system.
EUROPOWER EP4000/EP2000 User Manual The BEHRINGER EUROLIVE SERIES loudspeakers are an outstanding solution for expanding your P.A. system, because each frequency range/application has a speaker type that optimally suits its characteristics. ◊ Extreme clip limiter settings in bi-amp operating mode can result in balance shifting. XENYX X2222USB Mixing Console Fig. 3.
EUROPOWER EP4000/EP2000 User Manual 4. Installation 4.1.1 Using the binding posts Your EUROPOWER can be installed into a 19" rack and requires two rack units. Please use four attaching screws and washers for installation. Reinforce the back end, especially for on-the-road use. Please assure that enough cool air reaches the rack, especially when other rack equipment emanates a lot of heat.
EUROPOWER EP4000/EP2000 User Manual 4.2 Audio connections Various cables are needed for different types of applications. The following illustrations show the correct wiring. Always use high-grade cables. When connecting a balanced input signal, please make sure to exclusively use balanced cables for passing the signal further on. Otherwise, one single unbalanced cable can turn the entire signal unbalanced.
EUROPOWER EP4000/EP2000 User Manual Distortion Cooling EP4000 < 0.02% EP2000 < 0.01% at 10 dB below rated output power 20 Hz - 20 kHz, +0/-1 dB > 300 @ 8 Ω -100 dB EP4000 50x (34 dB) EP2000 40x (32 dB) Turn-on/off muting, AC coupling EP4000 Class H complementary linear output EP2000 Class AB complementary linear output Power Supply Mains Voltage/Breaker Input Sensitivity EP2000 1.15 V (+3.4 dBu) EP4000 1.23 V (+4.
EUROPOWER EP4000/EP2000 User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION PRODUCT FAMILY MODEL/MODEL/ MODEL Responsible Party Name: MUSIC Group Services US Inc. Address: 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA Phone/Fax No.
We Hear You