Quick Start Guide

12 13EUROLIVE F1220A Quick Start Guide
EUROLIVE F1220A Controls
(EN) Controls
(1)
(2)
(3)
First group control
(1) The POWER LED lights up when the
loudspeaker is put into operation.
(2) The CLIP LED lights up when signal distortion
occurs. Reduce the volume with the LEVEL
control until the CLIP LED (2) does not light
up any more, or occasionally lights up at
signalpeaks.
(3) To set the volume of the LINE or MIC signal,
use the LEVEL control. The left half of the
control range is for attenuating the LINE
signal. The right half is for raising the level of
the MIC signal.
Level adjusting: Turn the LEVEL control
whose signal you want to adjust slowly to
the right until the CLIP LED lights up only
at signal peaks. The LED is not supposed to
glowcontinuously.
(4)
Equalizer
(4) The F1220A features a 3-band sound control.
Each band provides a maximum boost/cut of
15 dB. At center position the equalizer has a
at response.
(5)
(6)
Feedback lter (notch lter)
(5) This switch turns on the feedback lter.
(6) This control adjusts the center frequency of
the feedback lter.
(7)
(8)
LINK OUTPUT
(7) + (8) The LINK OUTPUT is directly connected
to the inputs of the F1220A and carries the
input signal with no processing applied.
In this way, you can route the signal to
the input of another device (for example,
a second F1220A).
(9)
(10)
MIC/LINE INPUT
(9) Use this ¼" stereo jack to connect a signal
source that has ¼" output.
(10) Use this XLR connector to connect a signal
source that has XLR output.
Side Panel
(13)
(13)
(12)
Side panel F1220A
(11) Press POWER to turn on your F1220A.
(12) You can replace fuses at the FUSE SWITCH
of the F1220A. Always replace fuses with the
same type.
(13) The mains connection is established using a
cable with an IEC mains connector. Thiscable
is delivered with the F1220A. To avoid
ground-loop hum, loudspeakers and mixing
consoles should be connected to the same
powercircuit.
Check Out behringer.com for Full Manual
(ES) Controles
(1)
(2)
(3)
Elementos de control, primer grupo
(1) Al encender el altavoz se enciende también el
LED POWER.
(2) Si el nivel de la señal de entrada llegara a ser
muy alto se encenderá el LED CLIP. Reduzcael
nivel con el control LEVEL hasta que el LED
se apague o se encienda solamente de
maneraesporádica.
(3) El control LEVEL le permite regular el nivel
de la señal de entrada, tanto de línea como
demicrófono.
Ajuste de nivel: estando la señal presente,
gire el control LEVEL lentamente hacia la
derecha hasta que el LED CLIP (2) se encienda
brevemente con picos de nivel. El LED no
deberá permanecer encendido.
(4)
Ecualizador
(4) El F1220A dispone de un ecualizador de
3bandas. El nivel de cada banda se puede
aumentar o atenuar hasta 15 dB; en la
posición central el ecualizador no afecta a
laseñal.
(5)
(6)
Filtro antirrealimentación (ltro de muesca)
(5) Utilice este conmutador para activar el
ltroantirrealimentación.
(6) Utilice este control para determinar
la frecuencia central del ltro
antirrealimentación.
(7)
(8)
LINK OUTPUT
(7) + (8) La salida de enlace LINK OUTPUT está
conectada directamente con las entradas
del F1220A, y como tal puede retransmitir la
señal de entrada sin alteración alguna, lo que
le permite enviar dicha señal a otros equipos
(para enlazar dos o más F1220A, por ejemplo).
(9)
(10)
MIC/LINE INPUT
(9) Conector jack estéreo de 6,3 mm para fuentes
de sonido con el mismo tipo de conector.
(10) Conector XLR balanceado para fuentes de
señal con salida XLR.
Vista Lateral
(13)
(13)
(12)
Vista lateral del F1220A
(11) Con el interruptor POWER se enciende
elF1220A.
(12) PORTAFUSIBLES. Al reemplazar el
fusible debe hacerlo por uno que reúna
exactamente las mismas características.
(13) La conexión a red se realiza mediante
una toma de corriente estándar. En el
suministro se incluye un cable de red
adecuado. Paraevitar bucles de masa es
recomendable alimentar los altavoces
y la mesa de mezclas de la misma toma
decorriente.
Si quiere acceder al manual de
instrucciones completo, vaya a la página
web behringer.com