Service Support Document

ManualsBrandsBehringer ManualsAnalog SynthesizersAnalog 4-Voice Polyphonic Synthesizer with 37 Full-Size Keys, 4 VCOs, VCF, 2 LFOs, 2 Envelopes, Sync and Cross Modulation and Arpeggiator

page 1 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

Analog 4-Voice Polyphonic Synthesizer with

37 Full-Size Keys, 4 VCOs, VCF,

2 LFOs, 2 Envelopes, Sync and Cross

Modulation and Arpeggiator

Synthesizers and Samplers

MONOPOLY

Service Support Bulletin

History

Requirement

This calibration function is only available on 1.0.5 or later version rmware.

Date Version Note

2021-03-03 Rev0 Initial version

How to start calibration

Power o MONOPOLY rst.

Long press and hold button HOLD and POLY simultaneously.

Summary of content (6 pages)

PAGE 1
Synthesizers and Samplers MONOPOLY Analog 4-Voice Polyphonic Synthesizer with 37 Full-Size Keys, 4 VCOs, VCF, 2 LFOs, 2 Envelopes, Sync and Cross Modulation and Arpeggiator Service Support Bulletin History Date Version Note 2021-03-03 Rev0 Initial version Requirement This calibration function is only available on 1.0.5 or later version firmware. How to start calibration Power off MONOPOLY first. Long press and hold button HOLD and POLY simultaneously. 985-40000-01200 Rev.
PAGE 2
Synthesizers and Samplers MONOPOLY Cycle power on MONOPOLY. Wait approximately 2 seconds until power LED blinking slowly. Release all buttons. Sub Calibration Menu There are 3 sub calibration menus. Press the corresponding button to enter the sub menu.
PAGE 3
Synthesizers and Samplers MONOPOLY Calibration Procedure Follow all steps in the order they are presented. Start BEND WHEEL Calibration Press button MONO UNISON, then VCO1 LED will illuminate. Calibrate BEND WHEEL maximum position Move the BEND WHEEL to its maximum position. 985-40000-01200 Rev.A 2022-04-21 Confidential, for internal use only. Not to be reproduced.
PAGE 4
Synthesizers and Samplers MONOPOLY Calibrate BEND WHEEL minimum position Move the BEND WHEEL to its minimum position. Start BEND WHEEL dead zone calibration This step is to ensure that no bend information is sent while bend wheel is not being touched. 1. Make sure the BEND WHEEL is released and returned to its center position before further operation. 2. Press button POLY UNISON, then VCO2 LED will light up. 985-40000-01200 Rev.A 2022-04-21 Confidential, for internal use only. Not to be reproduced.
PAGE 5
Synthesizers and Samplers MONOPOLY Calibrate BEND WHEEL dead zone Move the BEND WHEEL within the dead zone where you don't feel the tension of the spring. Start MG1 WHEEL Calibration Press button POLY POLY, then VCO3 LED will illuminate. Calibrate MG1 WHEEL maximum position Move the MG1 WHEEL to its maximum position. 985-40000-01200 Rev.A 2022-04-21 Confidential, for internal use only. Not to be reproduced.
PAGE 6
Synthesizers and Samplers MONOPOLY Calibrate MG1 WHEEL minimum position Move the MG1 WHEEL to its minimum position. Complete calibration Short press HOLD + EFFECTS will confirm and save all calibration result. If successful, all BUTTON LEDs will blink at the same time for a while. Otherwise, it may be a failed calibration. NOTE: Press HOLD + MONO CHORD will cancel all calibration and return back to normal mode.