V-TONE GMX110/GMX210/GMX212/GMX1200H Version 1.
V-TONE GMX110/GMX210/GMX212/GMX1200H IMPORTANT SAFETY PRECAUTIONS 2
V-TONE GMX110/GMX210/GMX212/GMX1200H FOREWORD Dear Customer, welcome to the team of BEHRINGER users, and thank you very much for expressing your confidence in us by purchasing the BEHRINGER V-TONE.
V-TONE GMX110/GMX210/GMX212/GMX1200H 1. INTRODUCTION 1.3 Before you get started Thank you for the trust that you have placed in us by buying your V-TONE. You have gotten your hands on a latest-generation guitar amp that sets completely new standards when it comes to analog modeling. The V-TONE was carefully packed at the assembly plant to assure secure transport.
V-TONE GMX110/GMX210/GMX212/GMX1200H 2. CONTROL ELEMENTS AND CONNECTIONS Control elements of your V-TONE guitar amp are described in this section. All controls and connections are explained in detail, and we give you useful tips about using them. An illustration of the control elements with the corresponding numbering can be found on the separately included supplementary sheet.
V-TONE GMX110/GMX210/GMX212/GMX1200H + PHONES connector is used, the internal loudspeakers and the speaker outputs are disconnected. Power is supplied via an IEC connector. The matching cable is provided with the unit. Those signals that are connected to the SLAVE IN connectors are directly routed to the V-TONEs power amp. This way, you can connect an external guitar preamp or modeling amp (e. g. V-AMP 2 or V-AMP PRO) without using the internal preamp on your V-TONE. SERIAL NUMBER.
V-TONE GMX110/GMX210/GMX212/GMX1200H 3.2 Recording setup with an external effects device 3.
V-TONE GMX110/GMX210/GMX212/GMX1200H 3.4 Wiring the GMX1200H The GMX1200H head features two LOUDSPEAKER outputs (EXT LEFT and EXT RIGHT) that can be used to connect one or two external loudspeakers. To get the most power from the GMX1200H, both loudspeaker outputs should be used and connected to speakers with minimum 8 Ohms impedance. Loudspeaker outputs are automatically muted as soon as you activate the tuner or connect a set of headphones (see section 5.1).
V-TONE GMX110/GMX210/GMX212/GMX1200H The multi-effects processor works basically in stereo, whereby only the TAPE and PHONES outputs are influenced in the case of the GMX110. Both signals (left and right) are added up for the speaker and the mono power amp of the GMX110. However, you can still use stereo effects for recording purposes by utilizing the TAPE OUT or by playing with a second amp in stereo. The GMX210 and GMX212 can produce the effects in stereo because they have two built-in speakers.
V-TONE GMX110/GMX210/GMX212/GMX1200H 38-42 Chorus/Reverb: First, the signal goes through a chorus effect with varying intensity, and then it goes through a reverb. Adjustable parameter: chorus mix. 82-85 Pitch/Reverb: The signal first goes through a pitch shifter with various transpositions in half-tone increments (or smaller). A reverb follows. Adjustable parameter: pitch shifter mix.
+ V-TONE GMX110/GMX210/GMX212/GMX1200H Once you activate MIDI, FX tracking is no longer active, i.e. there is no assignment between an effect number and a channel. This means that when you switch a channel, the previously set effect is not automatically loaded up. As this assignment feature would probably cause confusion when controlling the V-TONE via a MIDI foot controller, it makes sense only when it is controlled from the enclosed footswitch or directly from the V-TONE.
V-TONE GMX110/GMX210/GMX212/GMX1200H You determine the input volume of the effect module by using MIDI controller #7. This lets you adjust the volume of your V-TONE to your own requirements. Since this controller does not control master volume, you should first adjust the maximum volume you need by using the master volume control, and then use MIDI controller #7 to lower the volume. This function is also called volume controller. s Activate the tuner by keeping the CHANNEL key pressed for a few seconds.
V-TONE GMX110/GMX210/GMX212/GMX1200H 6.2 Speaker connection 7. APPENDIX The GMX110 features a SPEAKER connector to which you can connect an additional loudspeaker. This additional loudspeaker should be able to handle at least 30 Watts and the impedance of 4 Ω. 7.1 MIDI implementation The GMX212 and GMX1200H feature two LOUDSPEAKERoutputs (EXT LEFT and EXT RIGHT) for connecting two loudspeakers or a single stereo loudspeaker unit. The output power rating is 60 W per channel.
V-TONE GMX110/GMX210/GMX212/GMX1200H 7.2 Effect presets 14 7.
V-TONE GMX110/GMX210/GMX212/GMX1200H 8. SPECIFICATIONS $8',2 ,13876 GUITAR IN Input Impedance INSERT RETURN Input Impedance SLAVE IN Input Impedance AUX IN Input Impedance TAPE IN Input Impedance *0; *0; - 1/4" TS, low-impedance, line level INSERT SEND LINE OUT Output Impedance Max. output level TAPE OUT Output Impedance Max. output level PHONES OUTPUT Max. output level SLAVE OUT Output impedance Max. output level /28'63($.(5 287387 Type Min.
V-TONE GMX110/GMX210/GMX212/GMX1200H 9. WARRANTY § 1 WARRANTY CARD/ONLINE REGISTRATION To be protected by the extended warranty, the buyer must complete and return the enclosed warranty card within 14 days of the date of purchase to BEHRINGER Spezielle Studiotechnik GmbH, in accordance with the conditions stipulated in § 3. Failure to return the card in due time (date as per postmark) will void any extended warranty claims.