User Manual ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 Audiophile 31-Band and 15-Band Stereo Graphic Equalizer with FBQ Feedback Detection System
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual Table of Contents Thank you........................................................................ 2 Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited Warranty............................................................ 3 1. Introduction................................................................ 5 1.1 Before you get started................
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality commercially-available speaker cables with ¼" TS plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual (2) Subsequently, the product must be returned in its original shipping carton, together with the return authorization number to the address indicated by MUSIC Group. (3) Shipments without freight prepaid will not be accepted. § 4 Warranty Exclusions (1) This limited warranty does not cover consumable parts including, but not limited to, fuses and batteries.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual 1. Introduction 1.1 Before you get started FBQ Feedback Detection System 1.1.1 Shipment The FBQ Feedback Detection System is one of the most outstanding characteristcs of our graphic equalizers. This ingenious circuitry lets you immediately recognize and eliminate feedback frequencies. The FBQ Feedback Detection System uses the LEDs in the frequency band faders to indicate the critical frequencies.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual 2. Control Elements and Connectors 2.1 Front panel In this chapter we will describe various control elements of your equalizer. All controls and connectors are explained in detail, and you will also find useful hints on how to best use them. Since the three equalizers in the FBQ series are fairly similar, let’s start with the control elements of the FBQ1502 and the FBQ3102 that are similar to the control elements found on the FBQ6200.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual (10) The POWER switch powers up your ULTRAGRAPH PRO. The POWER switch should always be in the “Off” position when you are about to connect your FBQ to the mains. To disconnect the unit from the mains, pull out the main cord plug. When installing the product, ensure that the plug is easily accessible. If mounting in a rack, ensure that the mains can be easily disconnected by a plug or by an all-pole disconnect switch on or near the rack.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual 2.3.2 Noise generator By using the built-in noise generator, you can create the so-called “pink noise” that can be used to adjust your P.A. system to specific acoustic characteristics of various venues. (21) Activate the pink noise generator by using the PINK NOISE switch. The built-in switch illumination blinks red when the pink noise generator is activated. (22) Read off the noise generator’s signal level on the LED display. 3.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual 3.1 Master equalizer in sound reinforcement systems This diagram shows a typical set-up with the ULTRAGRAPH PRO models (see fig. 3.1). 3.2 Equalizer in the monitor path When using your ULTRAGRAPH PRO in the monitor path, the same applies as when using it as described in section 3.1. Basically, the stage volume should be as low as possible because: To achieve optimal results, you should pay attention to several issues: 1.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual 3.2.1 Priming a monitor system Priming describes the process of detecting and supressing feedback frequencies. After placing and leveling your mics and monitors (incl. power amps), you should crank up the aux send controls of your mixer. Now, activate the FBQ feedback detection system by pressing the FBQ switch (3). The slide control LEDs (9) will turn dark.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual Unbalanced ¼" TS connector Insert send return ¼" TRS connector strain relief clamp strain relief clamp sleeve sleeve ring tip tip sleeve (ground/shield) sleeve ground/shield ring return (in) tip (signal) tip send (out) Connect the insert send with the input and the insert return with the output of the effects device. Fig. 4.2: ¼" TS connector Fig. 4.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual 5. Specifications FBQ6200 Audio Inputs Noise Generator INPUTS RF-filtered, servo-balanced XLR and ¼" TRS connectors Impedance 40 kW balanced and unbalanced Maximum input level +21 dBu balanced and unbalanced CMRR typ.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual FBQ3102 Audio Inputs Noise Generator INPUTS RF-filtered, servo-balanced XLR and ¼" TRS connectors Impedance 40 kW balanced and unbalanced Maximum input level +21 dBu balanced and unbalanced CMRR typ.
ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 User Manual FBQ1502 Audio Inputs Noise Generator INPUTS RF-filtered, servo-balanced XLR and ¼" TRS connectors Impedance 40 kW balanced and unbalanced Maximum input level +21 dBu balanced and unbalanced CMRR typ.
We Hear You
