B2092A TRUTH Users manual Version 1.
TRUTH B2092A IMPORTANT SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. CAUTION: WARNING: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel only. To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture.
TRUTH B2092A TRUTH High-Performance Active 360-Watt Studio Subwoofer for Mono, Stereo and Surround Applications B2092A s High-power 360-Watt amplifier delivers extreme dynamic range, with linear bass reproduction down to 32 Hz s 2 long-excursion 8'' loudspeakers with deformation-resistant aluminum die-cast chassis for minimal distortion even at highest volume levels s Dedicated Left, Right and Center XLR inputs and outputs for all stereo and surround applications s Incredible low-frequency enhancement
TRUTH B2092A FOREWORD TABLE OF CONTENTS Dear customer, welcome to the team of BEHRINGER users, and thank you very much for expressing your confidence in us by purchasing this studio subwoofer.
TRUTH B2092A 1.1 Before you get started 1.1.1 Shipment Your B2092A was carefully packed in the factory to guarantee safe transport. Nevertheless, we recommend that you carefully examine the packaging and its contents for any signs of physical damage that may have occurred during transit. + + + + + If the unit is damaged, please do NOT return it to us; instead, notify your dealer and the shipping company immediately, otherwise claims for damage or replacement may not be granted.
TRUTH B2092A Fig. 2.2: The B2092A connector panel LEFT IN and RIGHT IN. These are the balanced inputs on your B2092A. They are laid out as XLR connectors. Connect them to the outputs on your mixing console or with your preamplifier (see ch. 3.1). LEFT OUT and RIGHT OUT. These outputs carry the signals for the main left and right loudspeakers. The signal is tapped into post-crossover, i.e. without the bass segment used for the subwoofer.
TRUTH B2092A Connect the mixing console outputs to the B2092A inputs marked LEFT and RIGHT . If you are using active monitors as main loudspeakers (e.g. B2030A or B2031A), connect the left loudspeaker to LEFT OUT, and connect the right loudspeaker to RIGHT OUT. If using passive loudspeakers, connect LEFT OUT and RIGHT OUT connectors to the power amplifier inputs.
TRUTH B2092A making any changes, and then using the controls to finetune the settings, creating the best results possible. Therefore, first set the controls to the neutral position labeled TYPICAL, i.e. set PHASE to 0° and ROOM COMPENSATION to 0 dB. Start by placing the subwoofer roughly in the stereo center of your loudspeaker system. If the frequency response is not wellbalanced, move the subwoofer to the left or to the right, so that it excites different room modes.
TRUTH B2092A 5. SPECIFICATIONS AUDIO INPUTS Inputs Connectors Input Trim Input impedance Left, Center, Right, Sub XLR connector, balanced inputs ±6 dB 10 kΩ (balanced) AUDIO OUTPUTS Outputs Connectors Output impedance Left, Center, Right XLR, balanced 100 Ω COMPONENTS 2 Woofers Nominal impedance Ø 8" (210 mm) 8Ω AMPLIFIERS Power rating Noise max. 360 Watt (63 Hz / 0,3 % THD) >100 dB CROSSOVER Subsonic filter High-cut filter PHASE switch 33 Hz (18 dB/Oct.) 85 Hz (24 dB/Oct.
TRUTH B2092A 6. WARRANTY § 1 OTHER WARRANTY RIGHTS AND NATIONAL LAW 1. This warranty does not exclude or limit the buyers statutory rights provided by national law, in particular, any such rights against the seller that arise from a legally effective purchase contract. 2. The warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law.
