Version 1.0 August 2006 ULTRALINK UL2000B User’s manual DATA-MANFULL_UL2000B_ENG_Rev_A.pmd 1 04.09.
ULTRALINK UL2000B IMPORTANT SAFETY INSTRUCTIONS CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus should not be exposed to dripping or splashing and no objects filled with liquids, such as vases, should be placed on the apparatus.
ULTRALINK UL2000B TABLE OF CONTENTS 1. INTRODUCTION ......................................................................................................... 4 1.1 Before you get started .......................................................................................................... 1.1.1 Shipment ...................................................................................................................... 1.1.2 Registration .................................................................
ULTRALINK UL2000B 1. INTRODUCTION Thank you very much for expressing your confidence in the ULTRALINK Series by purchasing this unit. With the UL2000B from BEHRINGER, you have acquired a modern, high-performance wireless transmission system. Due to its amazing set of features, you can use the ULB2000 in any situation that requires the highest quality in sound and freedom of movement for live concerts, events and television productions.
ULTRALINK UL2000B 1.1.3 Initial operation of the receiver Assure adequate ventilation and never place your ULR2000 receiver on top of an amplifier or near radiators to avoid overheating. The wall power unit (model: E-SPS1) included in the delivery supplies the power to your ULR2000. Only use the external power supply delivered with the unit! The interchangeable AC plugs can be swapped at any time, adapting to various socket types in different countries (Fig. 1.1). 1.
ULTRALINK UL2000B 1.1.5 Online-Registration Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www.behringer.com (alternatively www.behringer.de) and kindly read the terms and conditions of our warranty carefully. Should your BEHRINGER product malfunction, our goal is to have it repaired as quickly as possible. To arrange for warranty service, please contact the retailer from whom the equipment was purchased.
ULTRALINK UL2000B DISPLAY All important parameters are shown in the display (ch. 2.1.2). SET The SET button has 2 functions: Press this button to bring up the menu. To confirm the values you set in the menu, press the SET button. UP and DOWN These two buttons let you navigate the menu and change the values shown in the display (e.g. frequency, channel number, preset number).
ULTRALINK UL2000B Alphanumeric display All the values and letters relevant to the operation of your ULR2000 are shown in the 6-digit alphanumeric display: for example, channel number, channel color, frequency and menu items. CHANNEL If the ULR2000 is in the basic setting (menu not selected), pressing the UP and DOWN buttons changes the transmission channel within the selected preset. If CHANNEL is lit, the individual channel numbers are shown (CHAN1, CHAN2, ...).
ULTRALINK UL2000B If menu is selected and you make no parameter changes for a while, the unit automatically exits the menu. 2.2.1 TUNE A freely selectable carrier frequency in the range between 798.100 - 805.900 MHz can be set in the TUNE menu. This frequency is then stored in one of the 8 storage slots in the user preset (Preset 1). Depending on the basic settings of your ULR2000 (ch. 2.2.5), when selecting a storage slot you will be prompted to enter a channel number or a channel color.
ULTRALINK UL2000B 0 dB: the receiver is not muted low dB value: the receiver is muted only if substantial noise is transmitted with the signal high dB value: the receiver is muted even if the noise floor is low Setting a Squelch value 1. Press the SET button to get to the menu. 2. Press the 3. Press the SET button again to get to the SQELCH submenu. The display shows the current dB value. UP button twice to get to SQELCH. 4.
ULTRALINK UL2000B 4. Press the COLOR). UP and DOWN buttons to set one of the 3 parameters (FREQU, CHANNL or 5. Press the SET button to store the parameter for the basic setting. The procedure is now over, and the new basic setting is shown in the display. 2.2.6 LOCK To prevent your settings from accidentally being changed, you can activate the keylock function (LOCK). With the exception of the SET button, all other buttons (including the Power button) are locked.
ULTRALINK UL2000B 3. Press the SET button again to get to the PRESET submenu. The display shows the currently active preset. 4. Press the 3 or 4). 5. Press the SET button to load up the preset you selected. The procedure is now over, and the basic setting is shown in the display again. UP and DOWN buttons to select the desired preset. The display shows PSET 1 (2, 3. ULB2000 TRANSMITTER 3.
ULTRALINK UL2000B 2. 3. A blink code indicates the charge level of the battery: 1 = Battery is nearly empty . . . 5 = Battery is fully charged Shortly after, a second blink code indicates the current channel setting for the transmitter: 1 = Channel 1 is selected ... 8 = Channel 8 is selected When the blink codes have indicated the operating state, a constant glowing of the LED indicates the operational readiness.
ULTRALINK UL2000B The value 0 is indicated by a very short blink of the LED, and you will easily tell a 0 from a 1. If no entry is made for more than 5 seconds (either on the selection switch or by pressing the POWER button), the LED blinks quickly 5 times, and the programming mode is aborted. After entering the 6 digits for the frequency value, enter another value to indicate the channel number under which the frequency will be stored. 4.
ULTRALINK UL2000B If you have not stored any of your own frequencies, the frequencies stored in the user preset (Preset 1) are identical to the frequencies stored in Preset 3. Loading a preset 1. Engage MUTE. The transmitter can now be switched into the programming mode. 2. Turn the selection switch to 0 and confirm your selection by keeping the POWER button pressed for 2 seconds. As a confirmation, the LED blinks slowly once and then once again with medium tempo.
ULTRALINK UL2000B Low Gain: the LED blinks once with medium tempo. High Gain: the LED blinks twice with medium tempo. If no entry is made for more than 5 seconds (either on the selection switch or by pressing the POWER button), the LED blinks quickly 5 times, and the programming mode is aborted. 6. After a second brief blink break, an additional blink code is given as a confirmation: Successful loading of a preset is signaled with two slow blinks. The transmitter leaves the programming mode.
ULTRALINK UL2000B 6. After a second brief blink break, an additional blink code is given as a confirmation: Two slow blinks signal that the Auto Mute setting was changed. The transmitter leaves the programming mode. If the setting for Auto Mute could not be stored, the LED blinks quickly 5 times. In this case, start anew with step 2. 7. Disengage MUTE. 3.2.7 Turning the transmitter off To turn off the transmitter, press the POWER button for 2 seconds.
ULTRALINK UL2000B Low Gain: The LED blinks once with medium tempo. High Gain: The LED blinks twice with medium tempo. 3.3.5 Auto Mute 1. Make sure the transmitter is not muted (MUTE switch is set to OFF). 2. Turn the selection switch to 7 or 8 and confirm your selection by briefly pressing the POWER button. 3. The LED indicates the Auto Mute status with the corresponding number of medium-tempo blinks:: Auto Mute turned off: The LED blinks once with middle tempo.
ULTRALINK UL2000B 5. INSTALLATION 5.1 Operating information The quality of the wireless transmission depends on various local factors as well as the degree of radiation and reception at transmitter and receiver, unlike the signal transmission over cable. To minimize the risk of interference, take the following suggestions into account for a smooth operation of the wireless system. 5.1.
ULTRALINK UL2000B To assure good reception, if possible, install the ULR2000 as high in a rack as possible, so that the antennae protrude above the upper edge of the rack. The ULR2000 requires one height unit (1 HE) for installation in a 19-inch rack. Please assure that there are additional 10 cm (4 inches) of free space in the back for connecting cables. For installation in a rack, use M6 machine screws and nuts.
ULTRALINK UL2000B 5.3 Audio connections The audio connections on the ULR2000 are laid out electronically balanced. Of course, you can connect unbalanced equipment to the balanced connectors. Fig. 5.2: XLR connections Fig. 5.3: 1/4" TS connector Fig. 5.4: 1/4" TRS connector The transmitter cannot be connected with a cable directly to a mixer, as is the case with wired microphones. The connection between transmitter and the ULR2000 receiver is wireless.
ULTRALINK UL2000B A cable connection is required to connect the headset to the transmitter. The plug connection is provided by means of mini XLR connectors, which ensure a secure operation due to their locking mechanism. Abb.5.5: Mini XLR connector of the ULB2000 22 DATA-MANFULL_UL2000B_ENG_Rev_A.pmd 22 5. INSTALLATION 04.09.
ULTRALINK UL2000B 6. SPECIFICATIONS 6.1 ULR2000 receiver RF characteristics Receiver principle Modulation Frequency range Receiving frequencies (for EU/US/CA) Channels Channel bandwidth Channel spacing (min.) Nominal/peak deviation Frequency stability Sensitivity (with compander) Antenna inputs Antenna input impedance Range True Diversity wideband FM 794 - 810 MHz 320 frequencies, between 798.1 - 805.
ULTRALINK UL2000B 6.2 ULB2000 transmitter RF characteristics Modulation wideband FM Frequency range 794 - 810 MHz Transmission frequencies (for EU/US/CA) 320 frequencies, between 798.1 - 805.9 MHz, adjustable in 25-kHz increments Channels 8, freely programmable and switchable Channel bandwidth < 200 kHz Channel spacing (min.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION ULTRALINK ULB2000/ULR2000 Responsible party name: MUSIC Group Services USA, Inc. Address: 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA Phone/Fax No.: Phone: +1 425 672 0816 Fax: +1 425 673 7647 ULTRALINK ULB2000/ULR2000 complies with the FCC rules as mentioned in the following paragraph: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
ULTRALINK UL2000B MICROPHONE QUICK START GUIDE 26 MICROPHONE QUICK START GUIDE DATA-MANFULL_UL2000B_ENG_Rev_A.pmd 26 04.09.