Quick Start Guide

14 WING Quick Start Guide 15
WING Overview
Scribble strips, meters, select
Each fader strip has a mini display screen called a scribble strip. This will indicate
information about the current channel/bus number, name and even a graphic
icon to quickly identify which channel is currently controlled by the fader and
associated buttons. A color bar above the scribble strip allows quick visual
identication of groups of related channels. Scribble strip details and color bar
options can be edited on the HOME screen/HOME tab by pressing the
CUSTOMIZE button.
Pressing the SELECT button directs the control focus of the Main Display and
Channel Strip section to that channel or bus. Only one SELECT button can be
active at any time.
The SOLO button will isolate that channel for monitoring, along with any other
channels or buses that are soloed. The MUTE button mutes the channel currently
assigned to that strip.
Stereo level meters provide input level information at a glance, from -60 dB to
Clip. The DYNAMICS LED will light whenever the dynamics threshold is exceeded,
thus triggering the compressor/expander. Likewise, the GATE LED will light
whenever the input signal falls below the noise gate threshold.
Main Display
The majority of the WING’s controls can be edited and monitored via the 10" touch
screen Main Display. Various screens can be accessed with the 7 buttons along the
left side of the screen, as well as the VIEW buttons located in each major section of
the top panel.
6 encoders along the bottom of the display allow parameter adjustments of the
items shown at the bottom of the current display screen. These are capacitive
knobs that will highlight elements on the screen as soon as the associated
knob is touched.
An additional 7th encoder to the right of the display can be used for context-
dependent control by rst touching an item on the Main Display, allowing for ner
adjustments compared to moving virtual knobs or faders. A multi-purpose button
beneath the 7th encoder performs similarly depending on the current screen.
For example, it can be used as a tap tempo when editing delay eects.
The large stereo meter will either display the main bus or solo bus levels.
The CLR SOLO button will release all channels and buses that are active in the
solo bus.
An overview of each screen is presented in Chapter 3.
The navigation arrows and value/scrub wheel perform functions pertaining to
DAW control as well as the USB Audio and WING-LIVE players. The wheel can also
ne-tune values of parameters assigned in the User layer of the Custom Controls
while respective buttons are depressed.
Channel Strip Section
The channel strip provides quick access to the primary parameters for the
currently-selected channel. A display screen provides dedicated editing details for
the parameter being adjusted, and various indications for input conguration,
bus and group assignments, and metering are always visible for convenience.
One of 7 channel editing blocks (including EQ) can be sent to the editing display
screen by pressing the associated button or touching the capacitive encoder knob
directly above. Press and hold the button to turn the block on or o.
Pressing the VIEW button will open the HOME screen of the selected channel
on the Main Display.
Once a block is already active, pressing the block button again will scroll through
several parameters for editing, and the associated encoder can be used for
adjustments. Small dots in the lower right corner of the display indicate how
many parameters can be scrolled through by repeatedly pressing the block button.
An additional EQ section has dedicated controls for adjustment of up to 6 EQ
bands for input channels and 8 bands for buses. Engage the EQ block by pressing
and holding the EQ button, then touch one of the 4 EQ encoder knobs to select a
band for adjustment. Press the SHIFT button to access the low and hi shelf bands,
and additional bands if editing a bus EQ.
The GAIN, WIDTH and FREQ buttons select which element of the current band will
be adjusted with the encoder.
Press the LISTEN button in the lower right corner to monitor the EQ band in
isolation. The BLEND/MIX knob acts as a wet/dry adjustment for the EQ block.
This can be used to exaggerate or de-emphasize the current EQ setting.
4-Channel Section
The edit section above the righthand fader bank oers a special set of dedicated
control elements. This can be parameters like gain, pan, lters or eects sends for
the selected bank of 4 channels.
Pressing one of the 8 buttons enables the 4 knobs and 4 buttons to control
channel properties without actually selecting the channel for editing. This makes
the 4-channel section independent from the main control surface, and would
allow for a second audio engineer to work in parallel to the FOH engineer.
Custom Controls
The Custom Controls section allows up to 4 rotary knobs and 8 buttons to be
congured for control of specic elements that should be available at all times
regardless of the main display screen focus. A common use could be the vocal
channel’s reverb send level. Presets can also be congured to suit dierent sets,
venues, operators, etc. Press the VIEW button to assign functions to the controls,
optimize the scribble strips, or reset the controls.