Owner's manual

ManualsBrandsBEI Sensors ManualsToolsHigh Resolution Inclinometers

INCLINOMETER

CANOPEN

Main Features

- Two axis digital inclinometer

- Angle measurement range of +/-5°, +/-15° and

+/-30°, Resolution up to 0.001°

- Active linearization and

temperaturecompensation

- Interface: CAN according to CAL

- Code: Binary

- Housing: 70 mm 

Programmable Parameters

- Resolution

- Preset value

- Two limit switches

- Baud-rate and CAN-identifier

- Heartbeat Function

- Transmission mode: Polled mode, cyclic mode,

sync mode

Electrical Features

- Highly integrated circuit in SMD-technology

- Polarity inversion protection

- Over-voltage-peak protection

Applications

- Structural engineering

- Levelling techniques

- Measuring techniques

- Inclinations

- Mechanical Structure

Summary of content (8 pages)

PAGE 1
INCLI NO METER CANOPEN Main Features - Two axis digital inclinometer Electrical Features - Highly integrated circuit in SMD-technology - Angle measurement range of +/-5°, +/-15° and +/-30°, Resolution up to 0.
PAGE 2
INCLI NO METER CANOPEN Technical Data Electrical Data Model INC 5 INC 15 INC 30 Measuring range +/- 5° +/- 15° +/- 30° Resolution 0.001° 0,001° 0,005° Accuracy (T = 0 °C .. +55 °C) 0,01° 0,01° 0,02° Inclination angle in x and y (1) +/-15° +/-40° +/-60° Damping period 0° -> 5° typical 1s 10%, 2s 1%, 3s 0,1% Interface Transceiver according ISO 11898, galvanically isolated by opto-couplers Transmission rate max.
PAGE 3
INCLI NO METER CANOPEN There is a resistor provided in the inclinometer, which must be used as a line termination on the Installation Electrical Connection The inclinometer is connected via 8 pin round connector or a Cable last device. ON OFF Instructions to mechanically install and electrically connect the inclinometer Do not connect the inclinometer under power! Bus address The setting of the node number is achieved via SDO-Object (see 4.2).
PAGE 4
INCLI NO METER CANOPEN Programmable Encoder - Parameter Resolution per 1° The parameter resolution per 1° is used to program the desired number of steps per revolution. The values 1, 10, 100 and 1000 can be programmed. Preset Value The preset value is the desired position value, which should be reached at a certain physical position of the axis. The position value is set to the desired process value by the parameter pre-set. Baudrate The Baudrate can be programmed via SDO, default 20KBaud.
PAGE 5
INCLI NO METER CANOPEN Mechanical Drawings Dimension housing (mm) Version 130305 CANopen Industrial Datasheet Page 5
PAGE 6
INCLI NO METER CANOPEN Reference Level The Inclinometer has a mounting reference angel (black line)for an optimal mounting of the inclinometer, which is parallel to the x-axis. This reference angle must be placed exactly parallel to the object to be measured to prevent or minimize any mechanical offset/cross sensitivity. Y X Reference angle Reference angle of the inclinometer, top view.
PAGE 7
INCLI NO METER CANOPEN Mounting and Installation Instruction The inclinometer is designed for a horizontal mounting, i.e. the base plate of the inclinometer with the three mounting holes needs to be placed on the horizontal plane of the object to be measured. It can be mounted with M4 screw as a maximum. The mounting surface must be plane and free of dust and grease. We recommend cheese head screws with metrical thread M4 for the mounting. Maximum fastening torque for the mounting screws is 10 Nm.
PAGE 8
INCLI NO METER CANOPEN Models/Ordering Description Description Typekey Absolute inclinometer Measuring range INC ... 005 -2- .. 1- H0- ... - 015 030 Number of axis Interface CA Version Mechanical construction horizontal Dynamik 2 mPas Connection connector, 8 pin P8M 1 m cable CRW Option W without - Ordering Description We do not assume responsibility for technical inaccuracies or omissions. Specifications are subject to change without notice.