Technical Manual of Century AM-EAS Systems Based on CAB68 V1.0 Copyright © 2019 Hangzhou Century Co., Ltd. All rights reserved.
Table of Contents 1 SYSTEM OVERVIEW ................................................................................ 2 1.1 The Main Features of Century AM-EAS Systems .......................................................................... 2 1.2 Important Safety Precautions ....................................................................................................... 3 2 3 SYSTEM CONCEPTS................................................................................. 4 CONFIGURATION..........
1 SYSTEM OVERVIEW CENTURY Acoustic-Magnetic (AM)EAS systems introduced in the manual are all based on CAB58 electronics – the latest development based on 20-year experience in EAS industry and 10-year experience in R&D and production of EAS systems. 1.1 The Main Features of Century AM-EAS Systems (1) Complying with worldwide practical requirement on frequency and operating principle in EAS industry. No special interfere to the other AM systems to obtain unfair advantages.
Guaranteeing continuous operation of the system. (15) Alarm counting. Following handling results. Finding possible defects of the system. (16) Oscilloscope in tuning software No need to bring physical oscilloscope for installation and service. Intuitively help technicians to set parameters properly. Help technicians to identify source of interference. (17) Remote controller for the simplest adjustment Easy to bring with. Most of parameters can be set with.
Antenna frame SYSTEM CONCEPTS Atento Classic Vista 2.1 Classic (CA78L/F1) ( CA79L/F2) Atento Grand Vista 2.1 Grand (CA78X/F1) ( CA79X/F2) Power cable for LC/XC: 3m Cable between LC/XC and LS/XS: 5m Configuration cable: 2.4m Cables 2 Note: The configuration cable between LC/XC and LS/XS includes a 4-core cable and a net cable.
3 CONFIGURATION 3.1 Hardware 3.1.1 Volume Description VR1 VR2 Function Potentiometer for adjusting buzzer’s sound level of LC/XC. Clockwise for louder sound, and anti-clockwise for lighter sound. Potentiometer for adjusting buzzer’s sound level of LS/XS. Clockwise for louder sound, and anti-clockwise for lighter sound. 3.2 Configuring System by Software Please refer to “AMC-G58 User Manual”. 3.3 Configuring Communication Module Please refer to “Communication Module Configuration”.
4 INSTALLATION There are different modes of combinations of antennas. The most commonly used mode of installation is transceiver antenna installation. So, it will be mainly introduced in this manual. 4.1 Connection 5.1.1LC/XC and LS/XS Cable kit between LC/XC and LS/XS antennas Power cable LC/XC LS/XS Attention: If the power cable betweenantennasis not long enough,the length of cablecan be increased according to technical specifications.The maximum length is 50 meters.
4.2 Modes of Combinations 4.2.1 Single-Antenna 0.75m 0.75m 1.05m 1.05m LC 4.2.2 Dual-Antenna 0.75m 1.5m 0.75m 1.05m 2.1m 1.05m LC LS 4.2.3 Tri-Antenna RX TX TX 0.3m 1.5m 1.5m 0.3m 0.4m 2.1m 2.1m 0.
5.2.4 Multi-Channel 0.75m 1.5m 1.05m 2.1m ................ LS 1.5m 0.75m 2.1m 1.05m LS/XS LC LC/XC 5.2.5 Checkout Control LC/XC LS/XS LC/XC ........ 5.2.
4.3 Installation Notes 4.3.1 Requirements on Environment 1 Ensure the antenna is installed in environment with good ventilation. 2 Ensure the environment is clean and dry. 3 Ensure there isno possibility for water to enter into the antenna frame. 4 Ensure there is no large metal object, such as metal door frame, cabinet or shopping cart close to antenna. 5 Ensure that there is no 58KHz tagclose to the antenna. 4.3.2 Requirements on Power Source 1.
6 Specifications Dimensions(mm) CA78 10
CA78X 11
CA79L/F2 12
CA79X/F2 13
7 Technical Support If you have any questions or suggestions about the Essential Series of Century AM systems, please do not hesitate to contact our technical support by email technicalsupport@century-cn.com, or our salespersons directly. FCC This device contains FCC ID: 2AP7X-DRM3 This device complies with part 15 of the FCC Rules. Operation is subject to the follow ing two conditions: (1) This device may not cause harmful interference.
