BL-R8189ME1 V1.2 SPEC
BL-R8189ME1 V1.2 SPEC Content 1. General Description ...................................................................................................................................3 2. Product Model Information ....................................................................................................................3 3. WIFI Specification .......................................................................................................................................3 3.1 WIFI features .
BL-R8189ME1 V1.2 SPEC 1. General Description The BL-R8189ME1 V1.2 is a highly integrated single-chip 802.11n Wireless LAN (WLAN) network SDIO interface (SDIO 1.1/ 2.0/ 3.0 compliant) controller. It is a WLAN MAC, a 1T1R capable WLAN baseband, and WLAN RF in a single chip. It provides a complete solution for a high throughput performance integrated wireless LAN device. 2. Product Model Information Model Number BL-R8189ME1 V1.2 FCC ID 2AN2O-RSW02 IC 23317-RSW02 3. WIFI Specification 3.
BL-R8189ME1 V1.2 SPEC 3.2 WIFI RF Performance Feature Description Standard IEEE 802.11 b/g/n 802.11 b: 11, 5.5, 2, 1 Mbps 802.11 /g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps Data Rate 802.11 n: MCS 0 to 7 for HT20MHz：65 Mbps MCS 0 to 7 for HT40MHz：150 Mbps IEEE 802.11b mode: CCK, DQPSK, DBPSK Modulation mode IEEE 802.11g mode: 64QAM, 16QAM, QPSK, BPSK IEEE 802.11n mode : 64QAM, 16QAM, QPSK, BPSK Ad-hoc Mode(Peer-to-Peer) Network Architecture Infrastructure mode Scatter Net Frequency Range 2.4GHz band: 2.
BL-R8189ME1 V1.2 SPEC 3.3 Block Diagram 3.4 Dimension 12.0*12.0*1.4mm (LxWxH) ，Tolerance: +/-0.
BL-R8189ME1 V1.2 SPEC 3.5 PIN Assignment Pin # Name Type Description 1 GND P GND 2 RF O WLAN RF pad 3 GND P GND 4~8 NC / NC 9 VBAT P VDD3.
BL-R8189ME1 V1.2 SPEC 20 GND P GND 21 NC / NC P VDIO for SDIO pin, the power supply is same as the 22 VDIOSDIO signal level of SDIO bus .Base on platform to choose 3.3V or 1.8V 23~30 NC / NC 31 GND P GND 32 NC / NC 33 GND P GND 34~35 NC / NC 36 GND P GND 37~40 NC / NC 41 GND P GND 42~44 NC / NC I: input O: output P: power 3.
BL-R8189ME1 V1.
BL-R8189ME1 V1.2 SPEC 4. Antenna Specification 4.1 Antenna lists Max No. Type Band(s) 1 PCB antenna 2.4GHz - 2.5GHz 3.7 2 PCB antenna 2.4GHz - 2.5GHz 3.3 roborock S6 3 PCB antenna 2.4GHz - 2.5GHz 4.2 roborock S4 4 PCB antenna 2.4GHz - 2.5GHz 3.7 roborock S5 Max 5 PCB antenna 2.4GHz - 2.5GHz 3.7 S5 Max Peak Gain(dBi) Host Model S501-01, S511-01, S551-01 4.
BL-R8189ME1 V1.2 SPEC 4.3 Antenna design requirements a) RF-line need 50Ω single line impedance； b) Antenna is 2.4G WiFi Frequency band MIFA type Board antenna c) Antenna length, width, shape(s) as follows，Company：mm； d) PCB thickness is 1.
BL-R8189ME1 V1.2 SPEC 5. FCC and IC Warning This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
BL-R8189ME1 V1.2 SPEC To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm.
