Ruby S BL-R8189ME1 V1.2 SPEC Ruby S
Ruby S BL-R8189ME1 V1.2 SPEC Content 1. General Description ...................................................................................................................................3 2. Product Model Information ....................................................................................................................3 3. WIFI Specification .......................................................................................................................................3 3.
Ruby S BL-R8189ME1 V1.2 SPEC 1. General Description The BL-R8189ME1 V1.2 is a highly integrated single-chip 802.11n Wireless LAN (WLAN) network SDIO interface (SDIO 1.1/ 2.0/ 3.0 compliant) controller. It is a WLAN MAC, a 1T1R capable WLAN baseband, and WLAN RF in a single chip. It provides a complete solution for a high throughput performance integrated wireless LAN device. 2. Product Model Information Model Number BL-R8189ME1 V1.2 FCC ID 2AN2O-RSW02 IC 23317-RSW02 3. WIFI Specification 3.
Ruby S BL-R8189ME1 V1.2 SPEC 3.2 WIFI RF Performance Feature Description Standard IEEE 802.11 b/g/n 802.11 b: 11, 5.5, 2, 1 Mbps 802.11 /g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps Data Rate 802.11 n: MCS 0 to 7 for HT20MHz：65 Mbps MCS 0 to 7 for HT40MHz：150 Mbps IEEE 802.11b mode: CCK, DQPSK, DBPSK Modulation mode IEEE 802.11g mode: 64QAM, 16QAM, QPSK, BPSK IEEE 802.11n mode : 64QAM, 16QAM, QPSK, BPSK Ad-hoc Mode(Peer-to-Peer) Network Architecture Infrastructure mode Scatter Net Frequency Range 2.
Ruby S BL-R8189ME1 V1.2 SPEC 3.3 Block Diagram 3.4 Dimension 12.0*12.0*1.4mm (LxWxH) ，Tolerance: +/-0.
Ruby S BL-R8189ME1 V1.2 SPEC 3.5 PIN Assignment Pin # Name Type Description 1 GND P GND 2 RF O WLAN RF pad 3 GND P GND 4~8 NC / NC 9 VBAT P VDD3.
Ruby S BL-R8189ME1 V1.2 SPEC 20 GND P GND 21 NC / NC P VDIO for SDIO pin, the power supply is same as the 22 VDIOSDIO signal level of SDIO bus .Base on platform to choose 3.3V or 1.8V 23~30 NC / NC 31 GND P GND 32 NC / NC 33 GND P GND 34~35 NC / NC 36 GND P GND 37~40 NC / NC 41 GND P GND 42~44 NC / NC I: input O: output P: power 3.
Ruby S BL-R8189ME1 V1.
Ruby S BL-R8189ME1 V1.2 SPEC 4. Antenna Specification 4.1 Antenna lists Max Host Model No. Type Band(s) 1 PCB antenna 2.4GHz - 2.5GHz 3.7 2 PCB antenna 2.4GHz - 2.5GHz 3.3 roborock S6 3 PCB antenna 2.4GHz - 2.5GHz 4.2 roborock S4 Peak Gain(dBi) S501-01, S511-01, S551-01 4.2 Wireless LAN antenna matching circuit 4.3 Antenna design requirements a) RF-line need 50Ω single line impedance； b) Antenna is 2.
Ruby S BL-R8189ME1 V1.2 SPEC c) Antenna length, width, shape(s) as follows，Company：mm； d) PCB thickness is 1.5mm，Copper-Layer 6，Antenna is Layer1； e) Antenna put on the edge of the pcb，Clearance around and below； 5. FCC and IC Warning This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s).
Ruby S BL-R8189ME1 V1.2 SPEC Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Ruby S BL-R8189ME1 V1.2 SPEC antenne. La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son functionnement. Limited by local law regulations, version for North America does not have region selection option. This device is intended for OEM integrators only. Please see the full grant of equipment document for restrictions.
