石头科技产品包装图纸 Roborock S6 MaxV Robot Vacuum Cleaner User Manual Before using the product, read this manual thoroughly and save it for future reference. 图纸 提供 单位 北京石头科技有限公司 材 质 工 艺 要 求 材质：105g哑粉，骑钉 成品尺寸：172*130mm 页数：40P 参考色：PANTONE Cool Gray 11 C PANTONE 185 C 尺寸偏差：±0.5mm 印刷偏位：±1mm 备 注 项目名称 料号 版本号 设计时间 设计师 Tanos V说明书FCC版 4.03.0173 V4.0 2020.01.14 许戈 设计师 比例 历 史 版 本 版本号：V2.0 修改点：Tanos V 修改人：许戈 说明书修改意见12.16.docx 版本号：V3.0 版本号：V4.
Roborock S6 MaxV Robot Vacuum Cleaner User Manual Before using the product, read this manual thoroughly and save it for future reference.
Safety Information 1 FCC IC Statement 6 Battery and Charging 8 Product Overview 9 Installation 15 Instructions for Use 21 Routine maintenance 25 Basic Parameters 32 Troubleshooting 33 FAQs 35
Safety Information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE), Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING To reduce the risk of fire, electric shock, or injury: ·Do not use outdoors or on wet surfaces. ·Do not allow to be used as a toy.
Safety Information ·For use only with roborock CDZ��RR or CDZ��RR charger. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. ·Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. ·Turn off the appliance before making any adjustments, changing accessories, or storing appliance.
Safety Information SAVE THESE INSTRUCTIONS Household use only. IMPORTANTES MESURES DE S CURIT L’utilisation d’un appareil électrique demande certaines précautions: LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CETAPPAREIL), Le non-respect des mises en garde et des instructions peut causer des chocs électriques, des incendies et/ou des blessures graves. AVERTISSEMENT ·Pour réduire les risques d’incendie, de choc électrique ou de blessure: ·Ne pas exposer à la pluie, Ranger à l’intérieur.
Safety Information ·User de prudence lors du nettoyage des escaliers. ·Ne pas aspirer des liquids inflammables ou combustibles, comme de l’essence, et ne pas faire fonctionner dans des en-droits où peuvent se trouver de tells liquides. ·Ne pas aspirer de matières en combustion ou qui dégagent de la fumée, comme des cigarettes, des allumettesou des cen-dres chaudes. ·Ne pas utiliser l’appareil si le sac à poussière ou le filter n’est pas en place. ·Emêcher une mise en marche accidentelle.
Safety Information ·Respecter toutes les instructions de chargement et ne pas charger la batterie ou l’appareil à des températures qui ne sont pas incluses dans la gamme de températures indiquées dans la notice d’instructions. Un chargement mal effctué. ·Confier les réparations à une personne qualifiée qui utilisera uniquement des pièces de remplacement identiques. Cette façon de faire garantira la sécurité du produit.
FCC IC Statement Compliance Information Product Name Robotic Vacuum Cleaner with Dock Charger Compliance Statement This device complies with part �� of the FCC Rules. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s).
FCC IC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part �� of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Battery and Charging ·Please keep the dock charger away from heat (such as heating plates). ·The battery must be removed from the appliance before it is scrapped. ·The appliance must be disconnected from the supply mains when removing the battery. ·The battery is to be disposed of safely.Please do not discard waste batteries. Leave them to a professional recycling organization. ·Do not wipe or clean the chargers shrapnel with a piece of wet cloth or wet hands.
Product Overview Robot Spot Clean Press to start spot cleaning Clean/Power ・ Press to start cleaning ・ Press and hold to turn the robot on or off Power indicator ・ White: Battery level ≥ 20%.
Product Overview Dustbin Robot WiFi indicator ・ Off: WiFi disabled ・ Flashing slowly: Waiting for connection ・ Flashing quickly: Connecting ・ Steady: WiFi connected Dustbin lid Dustbin latch System Reset Filter Air Vent Water Tank Latch Speaker 10
Product Overview Accessories Charging Dock Moisture-proof Mat Mop Cloth Bracket Power Cable Mop Cloth 11
Product Overview Robot and Sensors Dock Locator ReactiveAI™ Cameras Wall Sensor Infrared Fill Light Cliff Sensor Bumper OmniDirectional Wheel Charging Contact Side Brush LiDAR Sensor Main Wheel Vertical Bumper Main Brush Main Brush Cover Latch Water Tank 12
Product Overview Mopping Module Water Tank Stopper Water Filter Water Tank Water Tank Latch Mop Cloth Slot Mop Cloth Bracket Mop Cloth Bracket Latch Mop Cloth Attachment Zone 13
Product Overview Charging Dock Charging Dock Power Indicator Dock Location Beacon Charging Contacts 14
Installation Important Information 1. Tidy cables and loose items from the ground and move any unstable, fragile, precious, or dangerous items to prevent personal injury or property damage due to items becoming tangled in, struck by, or knocked over by the robot. 2. If using this robot in a raised area, always use a secure physical barrier to prevent accidental falls that may result in personal injury or property damage.
Installation Using the Robot 2. Secure the charging dock with the adhesive tape. Wipe the floor of the area where the charging dock will be placed with a dry cloth, then stick the enclosed double-sided tape to the floor. Place the dock onto the double-sided tape to secure it in place. 1. Place the charging dock Keep the Charging Dock on a level surface, flat against a wall. Connect the power cable to the Charging Dock and place any exposed cable into the cable slot.
Installation 4. Powering On and Charging 3. Attach the Moisture-Proof Mat After fixing the Charging Dock in place, use a dry cloth to clean the area where the Moisture-Proof Mat will be located. Peel off the outer layer of the double-sided tape attached to the bottom of the Moisture-Proof Mat, and stick the mat to the ground as shown. Press and hold the button to power on the robot. Wait until the power light is steady, and then place the robot on the Charging Dock to charge.
Installation Connect to the app ② Reset WiFi 5. Download the mobile phone app for more smart features. (Optional) a. Open the upper cover and find the WiFi indicator. and buttons until you hear the b. Press and hold the "Resetting WiFi" voice alert. Reset is complete when the WiFi indicator flashes slowly. The robot will then wait for a connection. The robot supports the Roborock or Mi Home app. Choose the one that best meets your needs.
Installation ③ Reinstall the water tank Using the Robot Slide the water tank into the robot until you hear it lock with a click. 6. Mopping the floor Note: To prevent excessive dirt buildup on the mop, floors should be vacuumed at least three times before the first mopping session. ① Remove the water tank Press the water tank latch and slide the tank backwards. ④ Install the mop cloth Dampen the mop cloth and wring it until it stops dripping.
Installation Using the Robot ⑤ Install the Mop Cloth Bracket 9. Remove the Mop Cloth Bracket When the robot returns to the Charging Dock after cleaning, press the latches on both sides, and slide the Mop Cloth Bracket backwards to remove it. Slide the bracket along the back of the water tank. A click indicates that it is locked in place. Note: Note: The mop cloth should be cleaned after 60 minutes of mopping to ensure water flow and cleaning quality.
Instructions for use On/Off Note: ・ Cleaning cannot start if the battery level is too low. Allow the robot to charge before restarting cleanup. ・ Before cleaning, tidy cables (including the power cable of the Charging Dock) from the floor. Loose cables may be dragged by the robot, resulting in the disconnection of electrical appliances or damage of cables and property. ・ If cleaning is completed in less than 10 minutes, the area will be cleaned twice.
Instructions for use Charging Spot Cleaning Auto: After cleaning, the robot will automatically return to the Charging Dock to recharge. Manual: In Pause mode, press the button to send the robot back to the Charging Dock. The power indicator will breathe as the robot charges. When the robot is in standby or pause mode, press the button to start spot cleaning. In this mode, the robot cleans an 1.5m x 1.5m square area centered on the robot.
Instructions for use Selective Room Cleaning Scheduled Cleaning Select one or multiple rooms for cleaning in the app. Use the app to set start times for scheduled cleanings. The robot will return to the Charging Dock after each cleaning cycle. Note: ・ A full map must have been created, and Map Saving mode switched on before this function can be used. ・ The robot may enter unselected areas during cleaning. Clear obstacles from the ground around the selected rooms as the robot may enter unselected areas.
Instructions for use No-go Zones/Virtual Barriers/ No-Mop Zone Refilling the water tank or cleaning the mop cloth Use the app to set no-go zones/virtual barriers/No-Mop Zone. The robot will not enter no-go zones and areas sealed off by virtual barriers while cleaning. No-mop zones only activate when the Mop Cloth Bracket is installed. To add water or clean the mop cloth, press any button to stop the robot and remove the mopping module.
Routine maintenance Main brush Using the main brush cleaning tool Clean weekly Use the tool blade to cut away entangled hair on the brush and to clean the bristles. 1. Turn over the robot, press the latch, and remove the main brush cover. 2. Pull out the main brush. Remove and clean the main brush bearing. 3. Rotate the main brush cap in the indicated unlock direction to remove the cap. 4. Use the main brush cleaning tool to remove any entangled hair on the brush or bearing. 5.
Routine maintenance Dustbin and filter Clean weekly 1. Open the top cover, squeeze the Dustbin latches and take out the Dustbin. 2. Open the Dustbin lid as indicated by the arrow and pour out the dirt.
Routine maintenance Washable filter Clean every two weeks 1. Open the Dustbin lid as indicated by the arrow and pour out the contents. 3. Remove the filter and clean it with water. Note: Do not touch the filter with hands, brushes, or sharp objects to avoid damage. 2. Fill the Dustbin with clean water and close the cover. Gently shake the Dustbin, then pour out the dirty water. Note: 4. Rinse repeatedly and tap the filter frame to remove as much dirt as possible.
Routine maintenance Battery Water tank The robot is equipped with a built-in high-performance lithium-ion battery pack. To maintain battery performance, keep the robot charged during normal use. 1. Open the water tank. 2. Rinse the water inlet filter. 3. Fill the tank with water, shake it, then pour out the water. Clean as required Note: If the robot will not be used for an extended period, turn it off and charge it at least every three months to avoid battery damage caused by overdischarge.
Routine maintenance Omni-Directional Wheel Reset the System Clean as required 1. Turn over the robot. 2. Use a tool, such as small screwdriver to pry out the axle and take out the wheel. 3. Rinse the axle and the wheel with water to remove any hair and dirt. 4. Air-dry, reinstall, and press the wheel and axle back in place. If the robot does not respond when a button is pressed or cannot be turned off, reset the system. Press the Reset button, and the robot will reset automatically.
Routine maintenance Robot sensors Clean monthly Use a soft dry cloth to wipe and clean all sensors, including: 1. ReactiveAI™ Cameras 2. Six cliff sensors at the bottom of the robot 3. Wall sensor on the right side of the robot 4.
Routine maintenance Holiday Energy Saving Function When the robot is docked, press and hold "Recharge" for 10 seconds or until you hear an alert sound. This will activate Holiday mode. In this mode the robot will switch to Low Power mode to minimize power consumption. This includes a dimming of the LED indicator, and the stopping of all non-charging related functions including cleaning, remote control over WiFi, and more.
Basic parameters Robot Charging Dock Name Parameters Name Parameters Appearance and Dimensions 353×350×96.5mm Appearance and Dimensions 151×130×98mm Battery 14.4V/5200mAh lithium battery Rated Power 28W Weight Approx. 3.6kg Rated Input 100-240VAC Wireless Connection WiFi Smart Connect Rated Output 20VDC 1.2A Rated Voltage 14.4VDC Rated Frequency 50-60Hz Rated Power 66W Charging Time <6h Note: The serial number is on a sticker on the underside of the robot.
Troubleshooting If an error occurs while the robot is cleaning, the power indicator will flash red and a voice alert will sound. Refer to the following table for troubleshooting. Error Solution Error 1: Rotate the laser head to check that it turns freely. The LDS unit is jammed. Remove any items blocking it then move the robot to a new location and restart. Error 2: Clean and lightly tap the bumper. The bumper is stuck. Tap the bumper repeatedly to dislodge any jammed items.
Troubleshooting If an error occurs while the robot is cleaning, the power indicator will flash red and a voice alert will sound. Refer to the following table for troubleshooting. Error Solution Error 11: High-intensity magnetic field detected. Move the robot away from the magnetic tape and restart. The robot is too close to a magnetic tape and cannot start. Move it to a new location and restart. Error 12: The battery is too low. Recharge before use. Low battery. Recharge before use.
FAQs Problem Solution Unable to power on The battery level is low. Put the robot on the Charging Dock and charge it before use. The battery temperature is too low or too high. Only use the robot within the range of 4-40°C (39-104°F). Unable to charge If the Charging Dock is not receiving power, check that both ends of the power cable are properly connected. If contact is poor, clean the contact areas of the Charging Dock and the robot. Confirm that the Charging Dock indicator is on.
FAQs Problem Solution Scheduled cleaning is not working The battery level is too low. Scheduled cleaning can only begin when the battery level is above 20%. Is power always being drawn when the robot is on the Charging Dock? The robot will draw power while it is docked to maintain battery performance, but power consumption is extremely low. Does the robot need to be charged for at least 16 hours the first three times it is used? No. The robot can be used any time after it has been fully charged once.
Robot Vacuum Cleaner Manufacturer: Beijing Roborock Technology Co., Ltd. Product Model: roborock S� MaxV Address of Manufacturer: Floor �, Suite ����, ����, ����, Building C, Kangjian Baosheng Plaza, No.� Heiquan Road, Haidian District, Bejing, P.R.CHINA For more product information, visit our website: www.roborock.com For after-sales support, email our after-sales service team: US/Non-Europe Support: support@roborock.com Europe Support: support@roborock-eu.
