Dryer DC 1560
Read this manual prior to initial operation of the product! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference. This User Manual will • Help you use your machine in a fast and safe way. • Read the User Manual before installing and starting your product.
1 Important safety information This section includes safety information that will help protection from risks of personal injuries or materialistic damages. Failure to follow these instructions shall cause any warranty and reliability commitment to become void. General safety • • • • • • • • • • • • • • • Never place the machine on a carpetcovered floor, otherwise, lack of airflow beneath the machine may cause electrical parts to overheat. This will cause problems with your machine.
• • • • • • • • • • • • • Do not reach into the machine when the drum is spinning. Unplug the machine when it is not in use. Never wash down the appliance with water! There is the risk of electric shock! Always disconnect by unplugging from the mains before cleaning. Never touch the plug with wet hands. Never unplug by pulling on the cable, always pull out by grabbing the plug only.
2 Installation Refer to the nearest Authorised Service Agent for installation of your product. CPreparation of location and electrical installation for the product is under customer’s responsibility. BInstallation and electrical connections must be carried out by a qualified personnel. APrior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products will cause risks for your safety.
fireplace. BDo not operate your product at the same time with heaters such as a coal or gas stove. Airflow may cause the chimney to flare up. Connection to water drain (Products with a condenser); In products equipped with condenser unit, water accumulated during the drying cycle accumulates in the water tank. You should drain accumulated water after each drying cycle.
First use wet and slippery surfaces. To install the plastic parts: 1. Tilt your product to backwards. 2. Fit the plastic parts on to the front adjustable feet. Press on the plastic parts to snap them into their seating. 3. Check the balance of your product again and readjust the adjustable feet if necessary. • • Electrical connection Connect the machine to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table.
3 Initial preparations for drying Things to be done for energy saving: • Make sure that you operate the product at its full capacity but pay attention to not exceeding it. • Spin your laundry at the highest speed possible when washing them. Thus, the drying time is shortened and energy consumption is decreased. • Pay attention to dry same types of laundry together. • Follow the instructions in the user manual for programme selection.
not be dried in the product since they • • • • • • emit flammable or explosive vapor. Do not dry items cleaned with industrial chemicals in the dryer. Do not dry your unwashed laundry in the dryer. Items soiled with cooking oils, acetone, alcohol, fuel oil, kerosene, stain remover, turpentine, paraffin and paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer.
4 Selecting a Program and Operating Your Machine Control panel 1 2 3 4 6 7 5 1. Filter cleaning warning light Warning light turns on when the filter is full. 2. Program follow-up indicator Used to follow-up the progress of the current programme. 3. Cancel audio warning Used to cancel the audio warning given at the end of the programme. 4. On/Off button Used to turn on and off the machine. 5. Programme selection knob Used to select a programme.
Preparing the machine 1. Plug in your machine. 2. Place the laundry in the machine. 3. Press the “On/Off” button. C Pressing the “On/Off” button does not necessarily mean that the programme has started. Press "Start/Pause/Cancel" button of the machine to start the programme. Program selection Decide the appropriate program from the table below which includes drying temperature in degrees. Select the desired program with the program selection button.
Program selection and consumption table EN 2 Program table Programs Capacity (kg) Spin speed in washing machine (rpm) Approximate amount of remaining humidity Drying time (minutes) Cottons / Coloreds 6 A Ready to Wear 3 6 A Ready to Iron 3 1200-1000 % 60 130 900-800 % 70 150 1200-1000 % 60 80-60 900-800 % 70 100-80 1200-1000 % 60 130-100 900-800 % 70 130 1200-1000 % 60 80-60 900-800 % 70 80-60 Synthetics 800 % 40 80-60 600 % 50 130-100 800 % 40 60-30 600 % 50
Auxiliary function Buzzer Cancel Models Equiped Your machine will send out an buzzer warning when the program comes to an end. If you do not want to hear this buzzing, you need to press the “Cancel Audio Warning” button. The relevant LED will light up when this button is pressed and an audio warning will not be given when the program comes to an end. Warning indicators C Warning indicators may differ according to the model of your machine.
process, but this process will extend the programme duration and increase energy consumption since the drying will be interrupted continuously. Therefore, it is recommended to add laundry before the drying programme has started. Child-proof lock There is a childproof lock to prevent any program interruption due to the pressing of keys while the program is on. The loading door and all keys except the “On/Off” key on the panel are deactivated when the child-proof lock is active.
5 Maintenance and cleaning Cover filter Lint and fibres released from the laundry to the air during the drying cycle are collected in the “Cover Filter”. C Such fibre and lint are generally formed during wearing and washing. C Always clean the filter after each drying process. C You can clean the filter and filter area by vacuum cleaner. To clean the filter: 1. Open the loading door. 2. Remove the cover filter by pulling it up and open the filter. 3.
4. Clean the condenser with pressurized water and wait until the water drains. 5. Replace the condenser with the side of it labelled with “Top” facing upwards. Lock the 4 condenser locks. Make sure that the red lock on the upper right corner is engaged securely. 6. Close the kick plate cover.
6 Solution suggestions for problems Drying process takes too much time • Meshes of the filter may be clogged. Wash with water. Laundry come out wet at the end of drying. • • Meshes of the filter may be clogged. Wash with water. Excessive laundry might have been loaded in. Do not overload the machine. Machine does not switch on or the program does not start. Machine is not activated when set. • It might have not been plugged in. Make sure that the machine is plugged in. • The loading door may be ajar.