Room Air Conditioner OWNER'S MANUAL Models : LG-BKE 7500 D - LG-BKE 7600 D LG-BKE 7650 D - LG-BKE 7700 D LG-BKE 7800 D Prior to installation, this air-conditioning unit must be submitted for approval by the utility service which provides electricity (EN 6055-3 Norm). IMP OR T ANT € P leas e read this owner's manual carefully and thoroughly before ins talling and operating your room air conditioner. € P leas e retain this owner's manual for future reference after reading it thoroughly.
Room Air Conditioner Owner’s Manual TABLE OF CONTENTS Safety Precautions.........................3 FOR YOUR RECORDS Write the model and serial numbers here: Model # Prior to Operation ..........................9 Serial # You can find them on a label on the side of each unit. Dealer's Name Introduction ..................................10 Electrical Safety ...........................11 Operating Instructions.................12 Maintenance and Service ............
Safety Precautions Safety Precautions This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage to properties only. ■ The meanings of the symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. ■ Installation Do not use damaged power cords, plugs, or a loose socket. • There is risk of fire or electric shock. Install the panel and the cover of control box securely.
Safety Precautions Be cautious when unpacking and installing the product. • Sharp edges could cause injury. Be especially careful of the case edges and the fins on the condenser and evaporator. Be sure the installation area does not deteriorate with age. • If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury. For installation, always contact the dealer or an Authorized Service Center.
Safety Precautions Use a dedicated outlet for this appliance. Grasp the plug to remove the cord from the outlet. Do not touch it with wet hands. Do not place a heater or other appliances near the power cable. • There is risk of fire or electrical shock. • There is risk of fire and electric shock. Do not allow water to run into electric parts. Do not store or use flammable gas or combustibles near the air conditioner. Do not use the product in a tightly closed space for a long time.
Safety Precautions Do not open the inlet grill of the product during operation. (Do not touch the electrostatic filter, if the unit is so equipped.) • There is risk of physical injury, electric shock, or product failure. Unplug the appliance before performing cleaning or maintenance. • There is risk of electrical shock. When the product is soaked (flooded or submerged), contact an Authorized Service Center. • There is risk of fire or eletric shock.
Safety Precautions Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods. • Avoid personal injury. Do not install the product where it will be exposed to sea wind (salt spray) directly. • It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could cause product malfunction or inefficient operation. ■ Operation Do not direct airflow at room occupants. (Don't sit in the draft.
Safety Precautions Always insert the filter securely. Clean the filter every two weeks or more often if necessary. • A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or damage. Do not insert hands or other objects through the air inlet or outlet while the air conditioner is plugged in. • There are sharp and moving parts that could cause personal injury. Use a firm stool or ladder when cleaning or maintaining the air conditioner.
Prior to Operation Prior to Operation Preparing for Operation ENGLISH 1. Contact an installation specialist for installation. 2. Plug in the power plug properly. 3. Use a dedicated circuit. 4. Do not use an extension cord. 5. Do not start/stop operation by plugging/unplugging the power cord. 6. If the cord/plug is damaged, replace it with only an authorized replacement part. Usage 1. Being exposed to direct airflow for a long time may be hazardous to your health.
Introduction Introduction Symbols used in this Manual This symbol alerts you to the risk of electric shock. This symbol alerts you to hazards that may cause harm to the air conditioner. NOTICE This symbol indicates special notes. Features This appliance should be installed in accordance with national wiring regulations. This guide acts as a guide to help to explain product features.
Electrical Safety Electrical Safety Temporary Use of an Adapter We strongly discourage the use of an adapter due to potential safety hazards. For temporary connections, use only a UL-listed adapter, available from most local hardware stores. Ensure that the large slot in the adapter is aligned with the large slot in the receptacle for a proper polarity connection. To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground terminal.
Operating Instructions Operating Instructions How to insert the Batteries 1. Remove the battery cover by pulling it according to the arrow direction. 2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly. 3. Reattach the cover by sliding it back into position. NOTICE Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries. Storage and Tips for using the Remote Controller • The remote controller may be stored by mounting it on a wall.
Operating Instructions Remote Control Operations The controls will look like the following. Signal transmitter 5 1 6 3 4 2 7 11 8 13 10 CANCEL ON OFF 9 12 SET AUTO CLEAN 17 14 16 15 Flip-up door (opened) Operation Mode Cooling Operation Auto Operation or Auto Changeover Healthy Dehumidification Operation Heating Operation • Cooling Model( ), Heat Pump Model( ) 1. START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2.
Operating Instructions Cooling operation 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Cooling Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling 3 ON Auto Changeover Healthy Dehumidification Heating (Heat pump model only) Close the door of the remote controller. Set the temperature lower than the room temperature.
Operating Instructions Auto operation (Optional) Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Auto Operation, press the operation mode selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow.
Operating Instructions Auto changeover operation(Optional) 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Auto Changeover Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling 3 Auto Changeover Healthy Dehumidification Heating (Heat pump model only) Close the door of the remote controller.
Operating Instructions Healthy dehumidification operation Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Healthy Dehumidification Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow.
Operating Instructions Heating operation (Heat pump model only) 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Heating Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling 3 ON Auto Changeover Healthy Heating Dehumidification (Heat pump model only) Close the door of the remote controller.
Operating Instructions Jet cool operation ENGLISH 1 Press the Start/Stop button. The unit will respond with a beep. 2 Press the Jet Cool button to operate the speed cooling mode and the unit will operate at super high fan speed on cooling mode for 30 minutes. For this operation P0 appears on the display.
Operating Instructions NEO PLASMA purification operation(Optional) 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. Press the PLASMA button. Operation will start when the button is pressed and stop when the button is pressed again. Make sure the plasma led lights up. 3 Set the fan speed again with the door of the remote controller closed. You can select the fan speed in four steps-low, medium, high or CHAOS.
Operating Instructions 2nd F operation ENGLISH 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller and press the 2nd Function button to operate functions printed blue color under buttons. (Check the indication of 2nd function on the display of the remote controller.) 3 2nd function disappears in a short time automatically or when the button is pressed again. CANCEL ON OFF SET AUTO CLEAN For more details, refer to functions next pages.
Operating Instructions Additional Features Sleep mode 1. Press the Sleep Mode Auto button to set the time you want the unit to stop automatically. 2. The Timer is programmed in one-hour increments by pressing the Sleep Mode Auto button 1 to 7 times. The sleep mode is available for 1 to 7 times. To alter the time period in steps of 1 hour, press the Sleep Mode Button while aiming at air conditioner. 3. Make sure the Sleep Mode Auto LED lights up.
Operating Instructions Vertical Airflow Direction Control 1. Press the Start/Stop button to start the unit. 2. Press Chaos Swing button and the louvers will swing up and down. Press the Chaos Swing button again to set the vertical louver at the desired airflow direction.
Operating Instructions Auto clean (Optional) 1. Whenever you press the AUTO CLEAN button, Auto Clean Function will be reserved and cancelled. 2. Auto Clean function works before and after cooling or dehumidification mode. For details, refer to the below points. 3. When the unit is started after the reservation of Auto Clean ,the Cool Start function operates and indoor Fan is started after 20 seconds. 4.
Operating Instructions Auto restart Helpful information Fan speed and cooling capacity. The cooling capacity indicated in the specification is the value when the fan speed is set to high, and the capacity will be lower at low or medium fan speed. High fan speed is recommended when you wish to cool the room quickly. High Speed NOTICE Auto restart function has set enable as factory default. But customer can set up by following this instruction.
Maintenance and Service Maintenance and Service Before performing any maintenance, turn off the main power to the system. Indoor Unit Grille, Case, and Remote Control Turn the system off before cleaning. To clean, wipe with a soft, dry cloth. Do not use bleach or abrasives. NOTICE Supply power must be disconnected before cleaning the indoor unit.
Maintenance and Service Replacement of purifying filter (Optional) Recomended use period : About 2 years 1. Remove front panel and air filters. ENGLISH Air filter 2. Remove air purifying filters. 3. Insert new air purifying filters. TRIPLE DEODORIZING Filter 2 3 4. Reinsert air filters and close front panel. Outdoor Unit The heat exchanger coils and panel vents of the outdoor unit should be checked regularly.
Maintenance and Service Common Problems and Solutions Before calling for service If you have problems with your air conditioner, read the following information and try to solve the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer. Air conditioner does not operate 1. Ensure that the air conditioner is plugged into a proper outlet. 2. Check the fuse or circuit breaker. 3. Check whether the voltage is unusually high or low.
Maintenance and Service Troubleshooting The air conditioner may be operating abnormally when: Air conditioner does not start Air conditioner does not cool as it should Possible Causes What To Do ■ The air conditioner is unplugged. • Make sure the air conditioner plug is pushed completely into the outlet. ■ The fuse is blown/circuit breaker is tripped. • Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. ■ Power failure.
