Automatic washing machine WM 5100 W WM 5100 S
Please read this manual first! Dear Customer, We hope that your product which has been manufactured in modern facilities and passed through a strict quality control procedure will give you the best results. Therefore, we advise you to read through this manual carefully before using your product and keep it for future reference. This operation manual will… …help you use your machine in a fast and safe way. • Please read the Operation Manual before installing and starting your machine.
TABLE OF CONTENTS 1 Your Washing Machine 4 Overview Specifications 4 5 2 Warnings 6 General Safety First Use Intended use Safety instructions If there are children in your house... 6 6 6 7 7 3 Installation 8 Removing packaging reinforcement 8 Opening the transportation locks 8 Appropriate installation location 8 Adjusting the feet 8 Connecting to the water supply.
1 Your Washing Machine Overview Figure 1 1 3 2 5 6 4 1 Top Lid 4 Height-adjustable Feet 2 Detergent Drawer 5 Door 3 Control Panel 6 Filter Cap 4 EN
Specifications Models WM5100W WM5100S Maximum dry laundry capacity (kg) 5 5 Height (cm) 84 84 Width (cm) 60 60 Depth (cm) 45 45 Net Weight (kg) 60 60 Electricity (V/Hz.) 230 V / 50hz 230 V / 50hz Total Current (A) 10 10 Total Power (W) 2200 2200 Spinning cycle (rpm max.) 1000 1000 Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly.
2 Warnings Please read the following information. Otherwise, there may be the risk of personal injury or material damage. Moreover, any warranty and reliability commitment will become void. for 3 seconds to cancel the program set in your machine before calling the authorized service. First Use • General Safety • • • • • • • Never place your machine on a carpet covered floor. Otherwise, lack of airflow from below of your machine may cause electrical parts to overheat.
If there are children in your house... companies that produce detergents for your machine. • Safety instructions • • • • • • • • • • This appliance must be connected to an earthed outlet protected by a fuse of suitable capacity. The supply and draining hoses must always be securely fastened and remain in an undamaged state. Fit the draining hose to a washbasin or bathtub securely before starting up your machine.
3 Installation Removing packaging reinforcement 3. Fit the covers (supplied in the bag with the Operation Manual) into the holes on the rear panel. (“P”) Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.
3. Important: Tighten all lock nuts up again. check if there is any water leakage at the connection points. Turn off the tap and remove the nut in case of any leakage. Retighten the nut carefully after checking the seal. To prevent any water leakage and any other damage to be caused by it, keep the taps closed when the machine is not in use. Connecting to the water supply. Important: • The water supply pressure required to run the machine must be 1-10 bar (0,1 – 1,0 MPa).
• • • • • • The end of the drain hose can be directly connected to the wastewater drain or to the washbasin. The fitting must be secured in all types of connections. Your house may be flooded if the hose falls out of its housing during water discharging. The hose should be attached to a height of at least 40 cm, and 100 cm at most.
4 Initial preparations for washing • Sorting the laundry • Sort the laundry according to type of fabric, color, and degree of soiling and permissible water temperature. Always follow the advice on the garment labels. • • Washing water Wash with Non machine- Do not wash temperature sensitive, short washable programs.
Detergent, softener and other cleaning agents Add detergent and softener before starting the washing program. Never open the detergent dispenser drawer while the washing program is running! When using a program without prewash, no detergent should be put into the pre-wash compartment (Compartment no. I). A program without pre-wash should not be selected if a detergent bag or a dispensing ball is going to be used.
for prewashing for main washing with hard water for washing machines and always follow the instructions on the package. Detergent quantity 1/2 measure 1 measure an additional 1/2 measure Softener Put the softener into the softener compartment of the detergent dispenser. • Use the proportions recommended on the packet. • Never exceed the (> max <) level marking; otherwise, the softener will be wasted without being used.
5 Selecting a Program and Operating Your Machine Control panel Figure 2 12 14 13 9 7 8 9 10 11 12 13 14 - On/Off Button Door Indicator * Program Follow-up Indicator Spin Speed Adjustment Knob * Temperature Adjustment Knob * Program Selection Knob Auxiliary Function Keys Start/Pause/Cancel Button * According to your machine’s model 14 EN 7
Turning the machine on choosing a program. C Always select the lowest required temperature. Higher temperature means higher power consumption. C For further program details, see, “Program Selection Table” You can prepare the machine for program selection by pressing the the “On/Off” button. When the “On/ Off” button is pressed, the “Lid” light illuminates indicating that the door is unlocked. Press the “On/Off” button again to shut down the machine.
clothes that bear “not machinewashable” labels for which hand wash is recommended on this program. It washes the laundry with very tender washing movements without damaging your clothes. speed selection knob, the machine will spin in the maximum possible rpm in the default setting of the selected program. Additional programs For special cases, there are also extra programs available: C Additional programs may differ according to the features of your machine.
Max. Load (kg) Programme Duration (~min) Water Consumption (l) Energy Consumption (kWh) Prewash Extra RinseRinse Plus Rinse Hold Spin speed reduction No Spin No Heat Program selection and consumption table Cottons 90 5 133 45 1.65 • • • • • • Cottons 60** 5 145 49 0.95 • • • • • • Cottons 40 5 142 49 0.69 • • • • • • A Class 40 Super 40 5 182 45 0.78 • • • Synthetics 60 2.5 113 52 0.92 • • • • • • Synthetics 40 2.5 104 52 0.
Auxiliary functions Auxiliary function selection keys • Desired auxiliary function depending on the program is selected. • Some combinations cannot be selected together. • Warning signal on the selected auxiliary function will light up. Auxiliary function buttons may differ according to the model of your machine.
The “Wash” light on the program followup indicator illuminates when “Start/ Pause/Cancel” button is pressed after selecting the washing program. The “Program finished” lamp illuminates and the “Wash” light will fade when the program comes to an end. The “Lid” light flashes. Meanwhile, the door will stay locked for your safety and when it is safe to open, the “Lid” and “Program Finished” lights remain on.
level in the machine is suitable. Laundry may be added or taken out by opening the door. If the “Lid” lamp does not light up continuously at the end of this time, the water level in the machine is not suitable and laundry cannot be added. You can resume the program by pressing the “Start/Pause/Cancel” button again. • Child-proof lock There is a childproof lock to prevent any program interruption because of pressing the keys while the program is on.
6 Quick instructions for daily use Preparation 1. Turn the tap on completely. Check if the hoses are connected tightly. 2. Place the laundry in the machine. 3. Add detergent and softener. Starting 1. Press the “On/Off” button. 2. Select the programme and the temperature. 3. If required (according to your machine’s model): – select any auxiliary function, – adjust the spin speed, – set the time delay, 4. Close the loading door. 5. Press Start/Pause/Cancel button.
3. Set the spin speed if spin speed adjustment is available on your machine. 4. Press “Start/Pause/Cancel” button. After the program is finished 1. “Program finished” lamp will light up on the program follow-up indicator. The lid can be opened after 2 minutes when the “Program Finished” and “Lid” lamps light up continuously. 2. Press the On/Off button to shut down the machine. 3. Turn the water tap off. 4. Eliminate any folding of the rubber seal on the loading door and check for impurities. 5.
7 Cleaning and care Detergent drawer • Remove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. Open the hole in the bellow with the aid of a toothpick if it is clogged. C Foreign metal substances in your machine can cause rust stains. In such cases: Clean the drum with a stainless steel cleaning agent. Never use steel wool or wire wool.
• • • • Remove the nuts of the water intake hoses to clean the surfaces of the filters on the water intake valves with an appropriate brush. If the filters are very dirty, you can pull them out by means of pliers and clean them. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under streaming water. Replace the gaskets and filters carefully and tighten the hose nuts by hand.
place. If your product is not supplied with an emergency drain hose, do the following as shown in the figure below: • • • • • Place a large container in front of the filter to receive water flowing from the filter. Loosen pump filter (anticlockwise) until water starts to flow out of it. Direct the flowing water into the container you have placed in front of the filter. You can use a piece of cloth to absorb any spilled water.
8 Troubleshooting Problem Program cannot be started or selected. Water in the machine. There is water coming from the bottom of the machine. Machine does not fill with water. Machine does not discharge water. Machine vibrates or shakes. Machine stopped shortly after the program started. The water being taken in is directly discharged. Cause Explanation / Suggestion Machine may have switched to self protection mode due to an infrastructure problem (such as line voltage, water pressure, etc.).
No water can be seen in the machine during washing. This is not a problem. The water level is not visible from the outside of the machine. The door is jammed. Water level might be above the lower level of Run either the “Pump” or “Spin” program. the door. Machine might be heating up the water or it may be Wait until the process is over. at the spinning cycle. Due to electrical safety mechanism, the door can only be opened a few Wait until the process is over. minutes after the program has stopped.
In the case of a paused countdown while taking in water: Timer will not countdown until the machine is filled with the correct amount of water. In the case of a paused countdown at the heating It continuously step: Time will not count washes. down until the selected Remaining for the time does not temperature program is reached count down. In the case of a paused countdown at the spinning step: There may be an imbalance of laundry in the machine. It continuously spins.
Insufficient amount of detergent used. Washing laundry loaded performance is Excessive into machine poor: Stain could not Wrong program and be removed, temperature might have not cleaned. been selected. Laundry Improper detergent may could not be have been used. whitened. Wrong type of detergent used. Use recommended amount of detergent appropriate for the laundry. Do not load the machine in excess. Select the proper program and temperature for the laundry to be washed.
If the water hardness is higher, using insufficient amount of detergent can cause the laundry to become stiff in time. Use appropriate amount of detergent according to the water hardness. If detergent is put in the prewash compartment although prewash cycle is not selected, the machine can take this detergent during rinsing or softener step. Softener should not come into contact with detergent when being added. Wash and clean the drawer with hot water.
There is too much foam. Machine does work. No light is on. The machine did not start after the program was selected and the ‘Start/ Pause/Cancel’ button was pressed. “Washing” and “Start/ Pause/Cancel” lights are flashing after the program is started. The “Lid” light is flashing. You may not be using proper detergent for automatic washing machines. Excessive amount of detergent may have been used. Too much detergent may have been used for a small amount of lightly soiled laundry.