Automatic washing machine WME 7267 W WME 7267 S WME 7247 S WME 7227 S WME 7227 W WME 7247 W
Please read this manual first! Dear Customer, We hope that your product which has been manufactured in modern facilities and passed through a strict quality control procedure will give you the best results. Therefore, we advise you to read through this manual carefully before using your product and keep it for future reference. This operation manual will… …help you use your machine in a fast and safe way. • Please read the Operation Manual before installing and starting your machine.
TABLE OF CONTENTS 1 Your Washing Machine 4 Overview . . . . . . . . . . . . . . . . . . . . . . 4 Specifications . . . . . . . . . . . . . . . . . . . 5 2 Warnings 6 General Safety . . . . . . . . . . . . . . . . . . 6 First Use . . . . . . . . . . . . . . . . . . . . . . . 6 Intended use . . . . . . . . . . . . . . . . . . . 6 Safety instructions . . . . . . . . . . . . . . . 6 If there are children in your house... . . 7 Electrical connection. . . . . . . . . . . . . .
1 Your Washing Machine Overview 3 4 1 2 5 6 1 - Detergent Drawer 4 - Control Panel 2 - Door 5 - Filter Cap 3 - Top Lid 6 - Height-adjustable feet 4 EN
WME7267W WME7247S WME7227S WME7247W WME7227W Models Maximum dry laundry capacity (kg) Height (cm) Width (cm) Depth (cm) Net Weight (kg) Electricity (V/Hz.) Total Current (A) Total Power (W) Spinning cycle (rpm max.
2 Warnings Please read the following information. Otherwise, there may be the risk of personal injury or material damage. Moreover, any warranty and reliability commitment will become void. Press “Start/Pause/Cancel” button for 3 seconds to cancel the programme set in your machine before calling the authorized service. First Use General Safety • • • • • • • Never place your machine on a carpet covered floor. Otherwise, lack of airflow from below your machine may cause electrical parts to overheat.
• • • • • • • • • fuse of suitable capacity. The supply and draining hoses must always be securely fastened and remain in an undamaged state. Fit the draining hose to a washbasin or waste system securely before starting up your machine. There may be a risk of being scalded due to high washing temperatures! Never open the door or remove the filter while there is still water in the drum. Otherwise, there may be the risk of flooding and possible injury due to the hot water.
elsewhere in the house. The moulded plug on this appliance incorporates a 13A fuse. Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the event of losing the fuse cover, the plug must not be used until a replacement fuse cover has been fitted. Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store.
3 Installation Removing packaging reinforcement 3. Fit the covers (supplied in the bag with the Operation Manual) into the holes on the rear panel. (“P”) Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.
• Open the taps completely after making the hose connection to check if there is any water leakage at the connection points. Turn off the tap and remove the nut in case of any leakage. Retighten the nut carefully after checking the seal. To prevent any water leakage and any other damage to be caused by it, keep the taps closed when the machine is not in use. • Models with a single water inlet should not be connected to the hot water tap.
national regulations. Power cord plug must be within easy reach after installation. • The voltage and the allowed fuse protection are specified in the section “Technical Specifications”. • The specified voltage must be equal to your mains voltage. • Connection via extension cords or multi-plugs should not be made. B A damaged power cable must be replaced by a qualified electrician.
4 Initial preparations for washing • Sorting the laundry • Sort the laundry according to type of fabric, color, and degree of soiling and permissible water temperature. Always follow the advice on the garment labels. • • Non machine Do not wash Washing water Wash with washable temperature sensitive, short programmes.
Detergent, softener and other cleaning agents Add detergent and softener before starting the washing programme. Never open the detergent dispenser drawer while the washing programme is running! When using a programme without pre-wash, no detergent should be put into the pre-wash compartment (Compartment no. I). A programme without pre-wash should be selected if a detergent bag or a dispensing ball is going to be used.
for prewashing for main washing with hard water follow the instructions on the package. Detergent quantity 1/2 measure 1 measure an additional 1/2 measure Softener Put the softener into the softener compartment of the detergent dispenser. • Use the proportions recommended on the packet. • Never exceed the (> max <) level marking; otherwise, the softener will be wasted without being used. • If the softener has lost its fluidity, dilute dense softener with water before placing it in the detergent drawer.
5 Selecting a programme and operating your machine Control panel Figure 1 1 6 2 7 3 4 8 1 - Spin Speed Adjustment Button 2 - Display 3 - Temperature Adjustment Button 4 - Programme Selection Knob 5 - On / Off Button 6 - Time Delaying Button (+/-) 7 - Auxiliary Function Buttons 8 - Start/Pause/Cancel Button 15 EN 5
Display symbols Figure 2 2.a - Spin Speed Indicator 2.b – Temperature Indicator 2.c – Spinning Symbol 2.d – Temperature Symbol 2.e – Remaining Time and Delaying Time Indicator 2.f – Programme Indicator Symbols (prewash/mainwash/rinsing/softener/ spinning) 2.g – Economy Symbol 2.h – Time Delaying Symbol 2.i – Door Locked Symbol 2.j – Start Symbol 2.k – Pause Symbol 2.l – Auxiliary Function Symbols Turning the machine on Plug in your machine. Turn the tap on completely.
ment. Less detergent should be put in the main wash compartment as the veil foams too much because of its meshed structure. • Woollens You can wash your machine-washable woollen garments at this programme. Wash by selecting the proper temperature according to the labels of your clothes. It is recommended to use appropriate detergents for woolens. Additional programmes For special cases, there are also extra programs available: C Additional programs may differ according to the model of your machine.
A You should use a lower spin speed for delicate laundries. Temperature selection Whenever a new programme is selected, the temperature anticipated for that programme appears on the temperature indicator (2b). To change the temperature, press the temperature button (Figure 1-3). Temperature falls with 10° decrements. Cold selection is shown with “-” symbol.
Programme selection and consumption table Auxiliary functions Energy Consumption (kWh) Quick Wash Extra Rinse Anti- Crease Plus water Rinse Hold 90 7 54 2.70 max. • • • • • • 90-Cold Cottons 60** 7 52 1.19 max. • • • • • • 90-Cold Cottons 40 7 64 0.72 max. • • • • • • 90-Cold Intensive 60 7 66 1.40 max. * • * Selectable temperature range °C Water Consumption (l) Cottons Programme Prewash Max.
Auxiliary functions Auxiliary function selection keys 7a • • • • 7b 7c 7d Depending on the programme, you can select the desired auxiliary function by pressing the buttons. Select the required auxiliary functions before starting the programme. Some combinations cannot be selected together. (Ex.: Prewash and Quick Wash. Symbol of the selected auxiliary function (Figure 2-2l) will light up.
if required, select the auxiliary functions. 3. Press “Time delaying” buttons “+” and “-” (Figure 1-6) to set your desired time delay. Time delaying symbol (Figure 2-2h) will flash. 4. Press “Start/Pause/Cancel” button (Figure 1-8). Then the time delay starts to count down. Time delaying symbol (Figure 2-2h) will light up. Start symbol (Figure 2-2j) will light up. The “:” in the middle of the displayed time delay will start flashing. • More laundry may be loaded or taken out during the time delay period.
Softener Softener symbol lights up at the beginning of softener step. Spin Spin symbol will light up at the beginning of the final spin, during “Spin” and “Pump” special programs. • If the machine is not spinning, the programme may be in rinse hold mode or the automatic spin correction system has been activated because of the excessive unbalanced distribution of the laundry in the machine. Changing the selections after the programme has started The selected spin speed and programme temperature fade out.
To deactivate the child-proof lock, press the 2nd and 4th auxiliary function buttons for 3 sec. “C:OFF” (Child lock is deactivated) label appears on the screen. (Figure 1-8). Standby symbol (Figure 2-2k) will fade. Start symbol (Figure 2-2j) will light up. The programme continues and only pumps out the water.
6 Quick instructions for daily use Preparation 1. Turn the tap on completely. Check that the hose is connected tightly. 2. Place the laundry in the machine. 3. Add detergent and softener. Starting 1. Press the “On/Off” button. 2. Select the programme and the temperature. 3. If desired (according to your machine’s model): – select any auxiliary function, – adjust the spin speed, – set the time delay, 4. Close the loading door. 5. Press “Start/Pause/Cancel” button.
After the programme is finished Programme indicator symbols on the screen will remain lit after the programme is finished. “End” will appear on the screen. 1. Open the loading door and take out the laundry when the door locked symbol on the display fades out. 2. Press the “On/Off” button. 3. Turn the water tap off. 4. Remove any folds in the rubber seal on the loading door and check for debris. 5. Leave the loading door and detergent drawer open to dry.
7 Cleaning and care Detergent drawer Remove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. C If more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned. 2. Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin.
• • • If the filters are very dirty, you can pull them out by means of pliers and clean them. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under streaming water. Replace the gaskets and filters carefully and tighten the hose nuts by hand. 3- An emergency drain hose is supplied with some of our models. Others are not supplied with this item.
• • • When there is no water left, turn the pump filter until it is completely loose and remove it. Clean any residues inside the filter as well as fibers, if any, around the propeller region. If your product has a water jet feature, be sure to fit the filter into its housing in the pump. Never force the filter while replacing it into its housing. Fit the filter fully into its housing; otherwise, water may leak from the filter cap.
8 Solution suggestions for problems Cause Explanation / Suggestion Programme cannot be started or selected. Machine may have switched to self protection mode due to an infrastructure problem (such as line voltage, water pressure, etc.). Bring your machine to factory settings by turning the programme selection knob. (see, Ending the programme through canceling) Water in the machine. There may be some water in your machine when you receive it.
The door is jammed. - Water level might be above the lower level of the door. - Machine might be heating up the wa- - Run either the “Pump” or “Spin” programme. ter or it may be at the spinning cycle. - Wait until the process is over. - Due to an electrical mechanism, the - Wait until the process is over. door can only be opened a few minutes after the programme has stopped. Machine fills with water when a process is cancelled. Inside of machine may be hot.
It continuously washes. Remaining time does not count down. In the case of a paused countdown while taking in water: - Timer will not countdown until the machine is filled with the correct amount of water. (On models with display) - Time might have gotten stuck during heating step. (On models with display) In the case of a paused countdown at the spinning step: There may be an imbalance of laundry in the machine.
- Washing performance is poor: Oily stains appear on laundry. - Washing performance is poor: Bad odour - Such odours and bacteria layers are formed on the drum as a result of continuous washing at lower temperatures and/or in short programmes. - Oily accumulations on the drum may - Leave the detergent dispenser drawer as well have stuck to the laundry. as the loading door of the machine ajar after each - Oily accumulations on the drum may washing.
Clothes do not smell like the softener. - If the water hardness is higher, using insufficient amount of detergent can cause the laundry to become stiff in time. Use appropriate amount of according to the water hardness. - Insufficient amount of detergent used.
Machine does work. Nothing is displayed on the screen. The plug might not be plugged in the mains outlet. Check the plug. Fuse may have blown. Check the fuse. Electricity may be cut off. Check the supply power. The “On/Off” button might have not Press this button. been pressed. The machine did not start after the program was selected and the «Start/Pause/Cancel» button was pressed. The front door may be ajar. The Rinse Symbol amongst the Program Indicator Symbols is flashing.
9 Guarantee Your new Beko product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase. • What is covered? • Repairs necessary as a result of faulty materials, defective components or manufacturing defect. • The cost of functional replacement parts, but excluding consumable items. • The labour costs of a Beko approved repairer to carry out the repair. • • • What is not covered? • Transit, delivery or accidental damage or misuse and abuse.
10 Service Please keep your purchase receipt or other proof of purchase in a safe place; you will need to have it should the product require attention under guarantee. agreement document. Otherwise please call the appropriate number above where service can be obtained at a charge. You should also complete the details below; it will help us assist you when requesting service.
