DAC2.
Explanation of symbols used in this manual or on the rear/underside of the apparatus: The Lightning Flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons.
Fuse replacement: This appliance is fitted with a non-rewireable 10 amp mains plug. The plug contains a 10 amp fuse. If the fuse has blown it can be replaced as follows: a) Pull out the black fuse cover/carrier. b) Remove and dispose of the blown fuse. c) Fit a new 10 amp BS1362 approved fuse into the carrier and push the carrier back into the plug. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Bel Canto products are automatically covered by a 90 day factory warranty that covers all internal parts and labor. Register online (http://www.belcantodesign.com/Belcanto_Warranty.html) within 30 days of purchase from an authorized dealer to automatically extend your warranty for 2 years starting from the date of purchase. If you do not have web access, please contact your dealer for assistance.
Because the DAC2.5 runs cool, it can be placed in many system locations without compromise. We do not recommend placing weights or other objects directly on the DAC2.5. This may scratch or mar the chassis finish. Do not use harsh chemicals when cleaning the outside of your DAC2.5. Single Ended RCA and Balanced XLR connectors are available.
Front Panel Control Knob: Variable Output Mode: The control knob is a continuously rotating control with a push-switch function. Always push the button with your finger in the direct center of the knob. Pushing the knob will switch between selectable values on the display. Rotating the control left or right will adjust the selected value. The DAC2.
The DAC2.5 Remote Control has a comprehensive set of control features that are not available on the front panel, including expanded programmability. To access all DAC2.5 control features press the button marked DAC towards the bottom of the remote control. (The Main CD controls will still operate in the DAC, PRE and Tuner modes.) PGM: Enter program mode. Here you can assign a four character name to each input, turn each input ON or OFF, and/or activate Home Theater Bypass for the Analog Input.
Display: Toggles through several display options: 1. Standard: displays selected Input on the left and Volume on the right. Phase: Invert the phase. If enabled, you will see a dash to the left of the volume. 2. Sample Rate: displays selected sample rate. Regardless of the display mode you are in, this display will appear whenever your source changes sample rate: When both Balance and Phase shift are in effect, you will see this: 3. Product Name 4. Software Version see page 6 for image 5. Display Off.
IMPORTANT: If using the DAC2.5 directly into a power amplifier, ensure that the Fixed/Variable Output button is in the OUT (variable) position. Operation in Fixed Mode directly into the amplifier could cause extreme output levels, clipping and damage to the loudspeakers, amplifiers or your ears! • IEC power cord jack: Connect the supplied or a quality aftermarket power cord from this jack. Note the power setting indicated on the back of the unit before connecting the power.
Using Headphones When headphones are inserted into the headphone jack, the volume can be adjusted via the control knob or remote regardless of whether the DAC2.5 is in Fixed or Variable mode. The input can be selected as normal from the front panel or remote. The main outputs of the DAC2.5 are disabled when headphones are in use. Output Connections We strongly recommend that you use the Balanced XLR output to drive your e.One amplifier. Because of the DC coupled nature of the DAC2.
Digital Section: Maximum Input Data Rate: 24bit Data at 192Ks/s: AES 110ohm XLR, SPDIF 75ohm, TOSLINK 24bit Data at 96Ks/s: USB Master Clock jitter: 2picosecond RMS Analog 24/192 DAC Section: Maximum Output: 4Vrms balanced XLR, 2Vrms RCA Output Impedance: 200 ohms balanced XLR, 100 ohms RCA Frequency Response: 20 Hz-20KHz, +/- 0.5dB THD+N: <0.0015%, 4Vrms balanced out, 1KHz Output Noise: 3.
Application of Council Directive(s): 2004/108/EC and 2006/95/EC, as amended Standard(s) to Which Conformity Is Declared: EN 55013:2001 + A1:2003 + A2:2006 EN 55020:2007 EN 61000-3-2:2006 EN 61000-3-3:1995 + A1:2001 + A2:2005 EN 60065:2002/A12:2011 Manufacturer: Bel Canto Design, Ltd. st 221 1 Street North Minneapolis, MN 55401 USA The equipment identified here conforms to the Directive(s) and Standard(s) specified above. Type of Equipment: Models: Date: Digital to Analog Converter DAC2.
version 4.