REF1000M M O N O AU D I O P O W E R AM P L I F I E R T A B L E O F C O N T E N T S Information Safety Information Certifications/Standards Warranty Unpacking Power Connection Setup and Placement Design Features Rear Panel Connections Tips for Operation Specifications Declaration of Conformity 2 3 4 4 4 5
Explanation of symbols used in this manual or on the rear/underside of the apparatus: The Lightning Flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons.
Fuse replacement: This appliance is fitted with a non-rewireable 10 amp mains plug. The plug contains a 10 amp fuse. If the fuse has blown it can be replaced as follows: a) Pull out the black fuse cover/carrier. b) Remove and dispose of the blown fuse. c) Fit a new 10 amp BS1362 approved fuse into the carrier and push the carrier back into the plug. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Bel Canto products are automatically covered by a 90 day factory warranty that covers all internal parts and labor. Register online (http://www.belcantodesign.com/Belcanto_Warranty.html) within 30 days of purchase from an authorized dealer to automatically extend your warranty for 2 years starting from the date of purchase. If you do not have web access, please contact your dealer for assistance.
Because the REF1000M runs cool, it can be placed in many system locations without compromise. We do not recommend placing weights or other objects directly on the REF1000M. This may scratch or mar the chassis finish. Do not use harsh chemicals when cleaning the outside of your REF1000M. IMPORT ANT! Make all connections before powering your unit! The e.One Series REF1000M is a mono audio amplifier designed to deliver over 500 watts into 8 ohm loads and 1000 watts into 4 ohm loads.
R Panel Connections Never Connect Either the Positive or Negative Speaker Output to Any Ground Contact! Connecting any Speaker Output on the REF1000M to Ground will cause the amplifier to go into protection and could damage the amplifier and void the warranty. 1) Power Switch: Power is on when the switch is toggled to the I position and off in the O position. 2) Input Connections and RCA/XLR switch: When using RCA cables for the input insure that the RCA/XLR switch is pressed in to the RCA position.
• In case there is hum or ground noise, check that the RCA/XLR switch is in the correct position for the type of connection being used. • Ensure that the preamplifier or any source components are not producing hum by setting the preamplifier to a MUTE or Standby setting. • The design of the REF1000M reduces the chance for ground loop induced hum, but we still recommend using shorter interconnect cables to the preamplifier.
Specifications Power Output: >1000W into 4 ohms, >500W into 8 ohms Minimum Load: 2 ohms Peak Output Current: 45 amperes Frequency Response: +/-0.5dB 20Hz-20KHz, all loads THD+N: 0.007% 1W, 1KHz, 4 ohms IMD (CCIF): 0.
Application of Council Directive(s): 2004/108/EC and 2006/95/EC, as amended Standard(s) to Which Conformity Is Declared: EN 55013:2001 + A1:2003 + A2:2006 EN 55020:2007 EN 61000-3-2:2006 EN 61000-3-3:1995 + A1:2001 + A2:2005 EN 60065:2002/A12:2011 Manufacturer: Bel Canto Design, Ltd. st 221 1 Street North Minneapolis, MN 55401 USA The equipment identified here conforms to the Directive(s) and Standard(s) specified above.
version 4.