User's Manual

PMP-3850 PARTS CHECKLIST
6
7. Short line cord for
wall installation
CID Redial
Talk
Flash
Mute
Save
MEM
Menu
Edit
Delete
9:45 10/11 38 3
AM
RPT
JOHN SMITH
555-555-1212
#
NEW
1. Handset 2. Base
4. AC power adapter
8. Quick start card
6. 7-foot line
cord for desk use
QUICK START GUIDE
PMP-3850
1. Connect the telephone line cord to the "LINE"
jack and to a telephone outlet.
2. Connect the AC power adapter to the 9V DC
jack and to an AC outlet.
Note: Use only the supplied AC power adapter.
Do not use any other AC power adapter.
Connect the AC power adapter to a contin-
uous power supply. Place the phone close
to the AC outlet so that you can plug in the
AC power adapter easily.
SETTING UP THE BASE
TEL LINE DATA
9VDC
300mA
1. Slide open the batter y compartment door on the bottom
of thehandset.
2. Plug the batter y connector into the 2-pin connector in the
battery compartment, and then insert the battery.
3. Close the batter y compartment door and place the
handset on the base unit cradle. You will hear a tone
and the CHARGE LED on the base will illuminate.
4. IMPORTANT: Charge the battery pack for at least 12
hours before using the handset the first time.
INSTALL THE BATTERY
1. Pick up the handset and press T.
2. Wait until you hear a dial tone and then dial the number you wish to dial.
3 When you are finished talking, press the T key or place the unit back
into the base to end the call.
Note: The CHARGE light on the base will illuminate when the line is active.
MAKING CALLS
9. Belt-Clip
3. 10-number
memory card
10. Ni-MH battery pack
BATTERIES: CAUTION
To reduce the risk of fire or injury to persons, read and follow these instructions:
• For the cordless handset, use only 3.6V 600mAh Nickel-Metal Hydride (Ni-MH),
cordless telephone battery pack PM-38BAT (included).
• Do not dispose of the batteries in a fire. The cells may explode. Check with local codes
for possible special disposal instructions.
• Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to short the battery with conducting
materials such as rings, bracelets, and keys. The battery or conductor may overheat
and cause burns.
• Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may occur causing burns or
irritation to eyes or skin.
• When inserting batteries into this product, the proper polarity or direction must be
observed. Reverse insertion of batteries can cause charging, and that may result in
leakage or explosion.
• Remove the batteries from this product if the product will not be used for a long period
of time (several months or more) since during this time the battery could leak in the
product.
• Do not store this product, or the batteries identified for use with this product, in high
temperature areas. Batteries that are stored in a freezer or refrigerator for the purpose
of extending shelf life should be protected from condensation during storage and
defrosting.
Batteries should be stabilized at room temperature prior to use after cold storage.
5
BATTERY CAUTIONARY INSTRUCTIONS
The EPA certified RBRC
®
Battery Recycling Seal on the nickel-metalhydride
(Ni-MH) battery indicates TT Systems LLC is voluntarily participating in an
industry program to collect and recycle these batteries at the end of their
useful life, when taken out of service in the United States or Canada. The
RBRC
®
program provides a convenient alternative to placing used Ni-MH
batteries into the trash or the municipal waste stream, which may be illegal in
your area. Please call 1-800-8-BATTERY for information on Ni-MH battery
recycling and disposal bans/restrictions in your area. TT Systems LLC’s
involvement in this program is part of our commitment to preserving our
environment and conserving our natural resources.