P72895_F1D104-OSD-univ_man.
P72895_F1D104-OSD-univ_man.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 3 Table of Contents English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 En Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Fr Deutsche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 De Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Ne Italian . . . . .
P72895_F1D104-OSD-univ_man.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 1 Introduction Thank you for purchasing the Belkin Components OmniView™ PRO KVM switch. Controlling 4 PCs from one keyboard, mouse and monitor has never been easier! The OmniView™ PRO gives you the ultimate in control. Compatible with AT and PS/2 style computers, it is loaded with features such as On-Screen Display, Integrated Mouse Conversion Technology and separate DB25 daisy-chain ports.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 2 Technical Specifications Console Connectors: Keyboard: Mouse: Monitor: (1) (1) (1) (1) 6 pin MiniDIN 6 pin MiniDIN (for PS/2 mouse) DB9 male (for spare serial mouse) HDDB15 female Computer Port Connectors: Keyboard: (4) 6 pin MiniDIN Mouse: (4) 6 pin MiniDIN (for PS/2 mouse) (4) DB9 male (for serial mouse) Monitor: (4) HDDB15 male Dimensions: Width: Height: Depth: 9.5" (237 mm) 2.3" (58 mm) 6.
P72895_F1D104-OSD-univ_man.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 4 List of Parts Needed Make sure you have the right cables! The OmniView™ PRO requires cables to connect the four computers you will be controlling. Below are the Belkin part numbers and their descriptions. We recommend purchasing Cable Kits based on the type of mouse port your computer uses.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 5 Hardware Installation Bank 0 (Master) 1 2 3 4 En Bank 1 (slave) 5 6 7 8 9 10 11 12 13 14 15 16 CONSOLE Keyboard, mouse and monitor Bank 2 (slave) Bank 3 (slave) The OmniView™ PRO has the capability to be daisy-chained to 3 more units (for a total of 4), giving the user control over a maximum of 16 computers! Each OmniView™ PRO unit is defined as a BANK. See diagram above for more information.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 6 Hardware Installation (continued) PLEASE FOLLOW THIS INSTALLATION PROCEDURE EXACTLY. NOT DOING SO MAY RESULT IN KEYBOARD AND/OR MOUSE ERRORS, OR FAULTY OPERATION. WARNING: Before attempting to connect anything to the OmniView™ PRO or the computers, make sure everything is powered off. Plugging and unplugging cables may cause irreversible damage to your computers and the OmniView™ PRO.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 7 Hardware Installation 3. (continued) Connect the keyboard and mouse to the OmniView™ PRO. If you have an AT-style keyboard, you will need an AT-PS/2 adapter (Belkin Part# F2N017). Back of OmniView™ PRO En PS/2 Mouse PS/2 Style Keyboard 4. Connect the first computer's VGA cable to the OmniView™ PRO.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 8 Hardware Installation 5. (continued) Connect the first computer's mouse cable to the OmniView™ PRO. If using a PS/2 cable (Belkin Part# F2N036-XX), connect one end to the PS/2 mouse port on the computer, and the other end to the PC1 PS/2 mouse port on the back of the OmniView™ PRO.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 9 Hardware Installation (continued) NOTE: Avoid pressing any keys on the keyboard or moving the mouse if the currently selected port has a computer that is in the process of booting up. This may cause the computer to not detect, or initialize the keyboard or mouse drivers properly. Daisy-Chaining the OmniView™ PRO: The OmniView™ PRO can be daisy-chained with additional OmniView™ PRO units through the DB25 daisy-chain ports.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 10 Hardware Installation (continued) • RESET the MASTER unit by pressing the BANK/SCAN and CHANNEL buttons simultaneously or by initiating the “Hot” key command [SCROLL LOCK], [SCROLL LOCK], [END]. This is necessary for the MASTER unit to detect the newly added slave unit. • Verify that the MASTER unit has detected the new slave by pressing the BANK/SCAN button.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 11 Usage Selecting which computer to operate can be done either by On-Screen Display, the CHANNEL button, or through keyboard “Hot” key commands. You will notice that after the OmniView™ PRO switches to another computer, the mouse will be inoperative for about 1-2 seconds. This is normal operation and ensures that proper mouse synchronization is established.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Usage Page 12 (continued) Bank 0 (Master) Bank 1 (slave) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CONSOLE Keyboard, mouse and monitor Bank 2 (slave) Bank F (slave) AutoScan Mode: Enable AutoScan mode In AutoScan mode, the OmniView™ PRO remains on one port for a number of seconds, before switching to the next. This time interval is set in the On-Screen Display menu. NOTE: There is no mouse or keyboard control in this mode.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 13 Usage (continued) On-Screen Display Menu Control: Enable the On-Screen Display Menu To get into the On-Screen Display (OSD) menu, press [SCROLL LOCK] [SCROLL LOCK] [SPACEBAR]. Immediately, the OSD overlay screen appears. This screen is generated by the OmniView™ PRO, and does not affect your computers or running software in any way. • You can navigate through the active ports by using the arrow keys.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 14 Usage (continued) SCAN TIME: Amount of time the OmniView™ PRO stays on one port before switching to the next port when in Scan Mode. SCAN TIME: ■ 7sec ■ 15sec DISPLAY TIME: ■ 7sec ■ 15sec ■ 30sec ■ 60sec ■ 30sec ■ 60sec [↕]: SELECT (INS): RENAME (Enter): COMPLETE (Esc): Exit DISPLAY TIME: Amount of time the OSD Menu or Port Name remains displayed on-screen after making a port selection.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 15 Troubleshooting General Problems: Q: The OSD menu does not display a "✹" on a port where a computer is connected and powered up. What do I do? A: • RESET the OmniView™ PRO by simultaneously pressing the BANK/SCAN and CHANNEL buttons on the front panel. Access the OSD menu again and it should have re-detected all the active ports. Q: When cascading, the MASTER unit does not see the slave unit(s).
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 16 Troubleshooting (continued) PS/2 Mouse Problems at the console or computers: Q: The mouse is not detected during boot-up. A: • Check the cables and make sure they are inserted properly in the correct ports. • Check your computer/motherboard documentation making sure that the PS/2 mouse port (or IRQ) is enabled. • Make sure the mouse is detected directly plugged into the computer. Rebooting is necessary when trying this.
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 17 Troubleshooting (continued) Q: The computers boot up fine, but the mouse does not work. A: • Check the cables and make sure they are inserted properly in the correct ports. • Check the cable and make sure that it is a straight-through DB9 male/female cable such as Belkin P/N F2N209-XX-T (XX is the length in feet).
P72895_F1D104-OSD-univ_man.qxd 7/16/01 3:24 PM Page 18 Information FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Components, of 501 West Walnut Street, Compton CA 90220, declare under our sole responsibility that the product: F1D104-OSD to which this declaration relates: Complies with Part 15 of the FCC Rules.
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 19 Introduction Nous vous remercions d’avoir choisi le commutateur OmniView™ PRO KVM (clavier/vidéo/souris) de Belkin Components. Il n’a jamais été aussi facile de commander quatre PC à partir d´un seul clavier, d´une seule souris et d´un seul moniteur ! L’OmniView™ PRO constitue le fin du fin en matière de commande de PC.
P72895_F1D104fOSD_man.
P72895_F1D104fOSD_man.
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 22 Liste des pièces nécessaires Vérifiez bien que vous avez les câbles appropriés ! Plusieurs câbles sont nécessaires pour raccorder à l´OmniView™ PRO les quatre ordinateurs que vous allez commander. Vous trouverez ci-dessous les numéros de pièces Belkin ainsi que leur description. Nous vous conseillons d´acheter les kits de câbles correspondant au type de port souris utilisé par votre ordinateur.
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 23 Installation du matériel Banc 0 (Maître) Banc 1 (esclave) 1 2 3 4 5 6 7 8 CONSOLE Clavier, souris et moniteur Fr Banc 2 (esclave) Banc 3 (esclave) 9 10 11 12 13 14 15 16 L’OmniView™ PRO peut être mis en cascade avec trois autres unités (dans une configuration regroupant donc 4 unités au total), ce qui permet à l’utilisateur de commander jusqu’à 16 ordinateurs ! Chaque OmniView™ PRO est appelé BANC (Bank).
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 24 Installation du matériel (suite) VEUILLEZ SUIVRE SCRUPULEUSEMENT CES INSTRUCTIONS. TOUT MANQUEMENT PEUT ENTRAÎNER DES ERREURS CLAVIER ET / OU SOURIS OU UN DYSFONCTIONNEMENT. AVERTISSEMENT : Avant de tenter de brancher quoi que ce soit à l´OmniView™ PRO ou aux ordinateurs, vérifiez que rien n’est sous tension.
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 25 Installation du matériel 3. (suite) Raccordez le clavier et la souris à l´OmniView™ PRO. Si vous avez un clavier AT, vous aurez besoin d´un adaptateur AT vers PS/2 (numéro de pièce Belkin : F2N017f). Dos de l´OmniView™ PRO Souris PS/2 Fr Clavier PS/2 4. Raccordez le câble VGA du premier ordinateur à l´OmniView™ PRO.
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 26 Installation du matériel 5. (suite) Raccordez le câble de la souris du premier ordinateur à l´OmniView™ PRO. Si vous utilisez un câble PS/2 (numéro de pièce Belkin : F2N036fXX), insérez une extrémité dans le port souris PS/2 de l´ordinateur et l´autre extrémité dans le port souris PS/2 PC1 situé à l’arrière de l’OmniView™ PRO.
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 27 Installation du matériel (suite) REMARQUE : Evitez d’appuyer sur une touche du clavier ou de bouger la souris si le port sélectionné correspond à un ordinateur en cours d’initialisation. En effet, ceci pourrait empêcher l’ordinateur de détecter ou d’initialiser comme il se doit les pilotes clavier et souris.
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 28 Installation du matériel (suite) • REINITIALISEZ l’unité MAÎTRE en appuyant simultanément sur les boutons BANK/SCAN (Banc/Balayage) et CHANNEL (Canal) ou en optant pour le racourci clavier [SCROLL LOCK], [SCROLL LOCK], [END] (clavier français : [Arrêt défil], [Arrêt défil], [Fin]). Ceci permettra à l’unité MAÎTRE de détecter la nouvelle unité esclave. • Vérifiez que l’unité MAÎTRE a détecté la nouvelle unité esclave en appuyant sur le bouton BANK/SCAN.
P72895_F1D104fOSD_man.qxd 7/16/01 3:26 PM Page 29 Utilisation Pour sélectionner l´ordinateur désiré, vous pouvez recourir au paramétrage à l’écran, au bouton CHANNEL (Canal) ou à des raccourcis clavier. Vous constaterez qu’une fois que l´OmniView™ PRO a commuté sur un autre ordinateur, la souris ne fonctionne pas pendant 1 à 2 secondes environ. Il s´agit là d´une réaction normale qui garantit l´établissement de la synchronisation de la souris.
P72895_F1D104fOSD_man.qxd 7/16/01 3:27 PM Page 30 Utilisation Banc 0 (Maître) Banc 1 (esclave) (suite) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CONSOLE Clavier, souris et moniteur Banc 2 (esclave) Banc 3 (esclave) Mode de balayage automatique : Activer le mode de balayage automatique En mode de balayage automatique, l’OmniView™ PRO reste sur un port pendant quelques secondes avant de passer au port suivant. Ce laps de temps est fixé dans le menu de paramétrage à l’écran.
P72895_F1D104fOSD_man.qxd 7/16/01 3:27 PM Page 31 Utilisation (suite) Commandes du menu OSD de paramétrage à l’écran : Activer le menu OSD de paramétrage à l’écran Pour accéder au menu OSD de paramétrage à l’écran, appuyez sur [SCROLL LOCK] [SCROLL LOCK] [SPACEBAR] (clavier français : [Arrêt défil] [Arrêt défil] [BARRE ESPACE]). L’écran OSD apparaît alors immédiatement. Cet écran est créé par l’OmniView™ PRO et il n’affecte en aucune façon ni votre ordinateur ni le logiciel utilisé.
P72895_F1D104fOSD_man.qxd 7/16/01 3:27 PM Page 32 Utilisation SCAN TIME (DUREE DU BALAYAGE) : Laps de temps durant lequel l’OmniView™ PRO reste sur un port avant de passer au port suivant en mode de balayage automatique. DISPLAY TIME (DUREE DE L’AFFICHAGE) : Laps de temps durant lequel le menu OSD ou le nom du port reste affiché à l’écran après la sélection du port.
P72895_F1D104fOSD_man.qxd 7/16/01 3:27 PM Page 33 Détection des erreurs Problèmes généraux : Q: Le menu de paramétrage à l’écran ne fait pas apparaître de « ✹ » sur un port auquel est branché un ordinateur. Que dois je faire ? R: • REINITIALISEZ l’OmniView™ PRO en appuyant simultanément sur les boutons BANK/SCAN et CHANNEL situés à l’avant. Accédez à nouveau au menu OSD. Tous les ports actifs devraient alors avoir été détectés.
P72895_F1D104fOSD_man.qxd 7/16/01 3:27 PM Page 34 Détection des erreurs (suite) Q: Les ordinateurs démarrent correctement mais le clavier ne fonctionne pas. R: • Vérifiez que les câbles sont correctement insérés dans les ports appropriés. • Vérifiez que le clavier fonctionne lorsqu´il est directement branché aux ordinateurs. • Essayez un autre clavier mais n’utilisez que des claviers à 101, 102 et 104 touches.
P72895_F1D104fOSD_man.qxd 7/16/01 3:27 PM Page 35 Détection des erreurs (suite) Q: Lorsque je commute d´un port a l´autre, le mouvement de la souris est complètement erratique. Que dois-je faire ? R: • REINITIALISEZ l’OmniView™ PRO en appuyant simultanément sur les boutons BANK/SCAN et CHANNEL à l’avant ou utiliser le raccourci [SCROLL LOCK] [SCROLL LOCK] [END] (clavier français : [Arrêt défil] [Arrêt défil] [Fin]) pour réinitialiser l’OmniView™ PRO. Accédez à nouveau au menu OSD.
P72895_F1D104fOSD_man.qxd 7/16/01 3:27 PM Page 36 Détection des erreurs (suite) Q: Lorsque je commute d´un port à l´autre, le mouvement de la souris est complètement erratique. Que dois-je faire ? R: • Réinitialisez l’OmniView™ PRO en appuyant simultanément sur les boutons BANK/SCAN et CHANNEL à l’avant de l’appareil. Accédez à nouveau au menu OSD. Tous les ports actifs devraient alors avoir été détectés. • Vérifiez que vous n´avez chargé qu´un pilote de souris série.
P72895_F1D104fOSD_man.qxd 7/16/01 3:27 PM Page 37 Informations Déclaration FCC DECLARATION DE CONFORMITE AVEC LES REGLES FCC SUR LA COMPATIBILITE ELECTROMAGNETIQUE Nous, Belkin Components, sis au 501 West Walnut Street, Compton CA 90220, déclarons sous notre seule responsabilité que le F1D104fOSD auquel se réfère la présente déclaration, est conforme à la partie XV du règlement FCC.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 39 Einleitung Vielen Dank für den Kauf des Computer-Masterswitch OmniView™ PRO von Belkin Components. Sie können damit vier PCs über nur eine Tastatur, einen Monitor und eine Maus bedienen – und zwar einfacher als je zuvor! OmniView™ PRO gibt Ihnen ein Maximum an Kontrolle über Ihre PCs. Der Masterswitch ist mit AT- und PS/2-Computern kompatibel und bietet eine Fülle an Leistungsmerkmalen wie z.B.
P72895_F1D104gOSD_man.
P72895_F1D104gOSD_man.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 42 Erforderliche Komponenten Verwenden Sie die richtigen Kabel! Sie benötigen für OmniView™ PRO Kabel zum Anschluß der vier Computer, die Sie über den Masterswitch bedienen werden. Die erforderlichen Kabel sind im folgenden mit ihren BelkinArtikelnummern aufgeführt. Wir empfehlen den Erwerb von Kabelgarnituren (welche Kabelgarnitur zu verwenden ist, hängt vom Mausanschluß Ihres Computers ab).
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 43 Hardware-Installation Bank 0 (Master) Bank 1 (slave) 1 2 3 4 5 6 7 8 9 10 11 12 KONSOLE Tastatur, Maus und Monitor Bank 2 (slave) De Bank 3 (slave) 13 14 15 16 Sie können den OmniView™ PRO mit drei weiteren OmniView™-Geräten verketten (d.h. insgesamt vier in Kaskade schalten) und so bis zu 16 Computer von einer zentralen Konsole aus bedienen! Jedes OmniView™ PRO-Gerät wird als “BANK” bezeichnet (siehe Abbildung oben).
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 44 Hardware-Installation (Fortsetzung) BITTE GEHEN SIE GENAU NACH DIESER INSTALLATIONSANLEITUNG VOR. BEI NICHT ORDNUNGSGEMÄßER INSTALLATION KÖNNEN TASTATUR- ODER MAUSFEHLER UND FEHLERHAFTER BETRIEB DIE FOLGE SEIN. WARNUNG: Stellen Sie sicher, daß alle Geräte ausgeschaltet sind, ehe Sie irgend etwas an OmniView™ PRO oder die PCs anschließen. Das Ein- und Ausstecken von Kabeln kann Computer und OmniView™ PRO dauerhaft beschädigen.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 45 Hardware-Installation 3. (Fortsetzung) Schließen Sie Tastatur und Maus am OmniView™ PRO an. Zum Anschluß einer AT-Tastatur benötigen Sie einen AT-PS/2-Adapter (Belkin Artikel-Nr. F2N017g). Rückseite des OmniView™ PRO PS/2-Maus PS/2-Tastatur 4. Schließen Sie das VGA-Kabel für den ersten Computer am OmniView™ PRO an (verwenden Sie hierzu das Belkin VGA-Kabel F2N025gXX-T oder A3H981gXX).
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 46 Hardware-Installation 6. (Fortsetzung) Schließen Sie das Tastaturkabel für den ersten Computer am OmniView™ PRO an. Verwenden Sie hierzu ein weiteres PS/2-Kabel (Belkin Artikel-Nr. F2N036gXX), und stecken Sie ein Ende in den PS/2-Tastaturanschluß am Computer ein, und das andere Ende in den Tastaturanschluß PC1 auf der Rückseite des OmniView™ PRO.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 47 Hardware-Installation (Fortsetzung) Verkettung von OmniView™ PRO-Geräten: Sie können OmniView™ PRO mit zusätzlichen OmniView™ PRO-Geräten über die gesonderten DB25-Anschlüsse für die Kaskadierung verketten. Für einen einwandfreien Betrieb wird das Kaskadierungskabel F1D108gCBL benötigt (nicht enthalten). In diesem Beispiel sind vier OmniView™ PRO-Geräte verkettet und geben dem Bediener die Kontrolle über 16 Computer.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 48 Hardware-Installation (Fortsetzung) • Setzen Sie das MASTER-Gerät zurück, indem Sie gleichzeitig die Schalter BANK/SCAN und CHANNEL drücken (RESET) oder den Tastaturbefehl [SCROLL LOCK], [SCROLL LOCK], [END] ausführen. Dies ist notwendig, damit das MASTER-Gerät das neu hinzugefügte SlaveGerät erkennen kann. • Drücken Sie den Schalter BANK/SCAN, um zu überprüfen, ob das MASTER-Gerät das neue Slave-Gerät erkannt hat.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 49 Anwendung Der zu bedienende Computer kann über die On-Screen Display-Menüfunktion, den Schalter CHANNEL oder über Tastaturbefehle ausgewählt werden. Wenn OmniView™ PRO auf einen anderen Computer umschaltet, ist die Maus etwa 1 bis 2 Sekunden nicht funktionsfähig. Dieses Verhalten ist normal und gewährleistet die ordnungsgemäße Maussynchronisation.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 50 Anwendung (Fortsetzung) Bank 0 (Master) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Bank 1 (slave) KONSOLE Tastatur, Maus und Monitor Bank 2 (slave) Bank F (slave) AutoScan Mode: Aktivieren des AutoScan-Modus Im AutoScan-Modus schaltet OmniView™ PRO in Intervallen von einigen Sekunden von einem Computer zum nächsten. Dieses Zeitintervall wird im On-Screen Display-Menü eingestellt.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 51 Anwendung (Fortsetzung) On-Screen Display-Menüfunktion: Aktivieren der On-Screen Display-Menüfunktion Zum Aufrufen des On-Screen Display (OSD)-Menüs drücken Sie die Tasten [SCROLL LOCK] [SCROLL LOCK] [SPACEBAR]. Daraufhin erscheint der OSD-Overlay-Bildschirm. Dieser Bildschirm wird von OmniView™ PRO generiert und hat keine Auswirkungen auf die Computer oder laufende Software. • Mit den Pfeiltasten können Sie die aktiven Anschlüsse ansteuern.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 52 Anwendung SCAN TIME (ABFRAGEZEIT): Zeitdauer, die OmniView™ PRO auf einem Anschluß verbleibt, bevor es zum nächsten Anschluß weiterschaltet, wenn der Scan-Modus aktiviert ist. DISPLAY TIME (ANZEIGEZEIT): Zeitdauer, die das OSD-Menü oder der Anschlußname am Bildschirm angezeigt bleibt, nachdem ein Anschluß ausgewählt wurde.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 53 Fehlersuche (Fortsetzung) Monitor-/Grafikprobleme: F: Das Bild ist verschwommen, oder Geisterbilder bzw. Schatten werden angezeigt. A: • Überprüfen Sie die Verkabelung, und stellen Sie sicher, daß alle Kabel ordnungsgemäß eingesteckt sind. • Die eingestellte Auflösung und/oder Bildfrequenz ist sehr hoch, oder das Kabel ist zu lang. Tauschen Sie die VGA-Kabel gegen doppelt geschirmte Koaxialkabel aus (z.B. Belkin A3H981gXX).
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 54 Fehlersuche (Fortsetzung) • Drücken Sie gleichzeitig die Tasten BANK/SCAN und CHANNEL auf der Gerätevorderseite, um OmniView™ PRO zurückzusetzen (RESET). Rufen Sie das OSD-Menü erneut auf, um zu prüfen, ob alle aktiven Anschlüsse erneut abgefragt und erkannt wurden. F: Die Computer fahren ordnungsgemäß hoch, aber die Maus funktioniert nicht.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 55 Fehlersuche (Fortsetzung) • Stellen Sie mit Hilfe des Handbuchs für PC/Hauptplatine sicher, daß die seriellen Anschlüsse aktiviert sind und daß keine IRQ- oder Basisadressenkonflikte mit anderen seriellen Anschlüssen oder Modems bestehen. • Stecken Sie eine serielle Maus direkt in den Computer ein, und starten Sie den Computer neu.
P72895_F1D104gOSD_man.qxd 7/16/01 3:29 PM Page 56 Information FCC-Erklärung ERKLÄRUNG DER KONFORMITÄT MIT DEN FCC-VORSCHRIFTEN FÜR VERTRÄGLICHKEIT ELEKTROMAGNETISCHE Wir, Belkin Components, in 501 West Walnut Street, Compton CA 90220, erklären hiermit in alleiniger Verantwortung, daß das Produkt F1D104gOSD auf das sich diese Erklärung bezieht, Teil 15 der FCC-Vorschriften entspricht.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:30 PM Page 57 Inleiding Belkin Components dankt u hartelijk voor de aankoop van de OmniView™ PRO KVM schakelmodule. Nog nooit was het zo gemakkelijk met slechts één toetsenbord, muis en monitor liefst vier PC’s aan te sturen. De OmniView™ PRO biedt u de meest geavanceerde computerbesturing die vandaag beschikbaar is.
P72895_F1D104nOSD-univ_man.
P72895_F1D104nOSD-univ_man.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 60 Onderdelenlijst ZORG VOOR DE JUISTE KABELS! Voor de aansluiting van de vier computers die u met de OmniView™ PRO kunt aansturen, hebt u bepaalde kabels nodig. Onderstaand vindt u de betreffende Belkin typenummers met de bijbehorende beschrijving. Wij adviseren de aanschaf van kabelsets die gebaseerd zijn op het type muispoort dat uw computer gebruikt.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 61 Apparatuur installeren Bank 0 (Master) Bank 1 (Slave) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CONSOLE Toetsenbord, muis en monitor Bank 2 (Slave) Bank 3 (Slave) U kunt een OmniView™ PRO module doorverbinden naar drie dito modules. Daardoor kunt u niet minder dan 16 computers centraal aansturen! Het aantal modules per configuratie is maximaal vier. Elke OmniView™ PRO module wordt als BANK gedefinieerd.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 62 Apparatuur installeren (vervolg) HOUD U ZORGVULDIG AAN DEZE INSTALLATIEPROCEDURE. WIJKT U DAARVAN AF, DAN KAN DAT LEIDEN TOT HET SLECHT FUNCTIONEREN VAN TOETSENBORD EN/OF MUIS EN EEN ONNAUWKEURIGE BESTURING. WAARSCHUWING. Zorg dat alle apparaten uitgeschakeld zijn voordat u iets op de OmniView™ PRO of de computers aansluit. Het aansluiten en ontkoppelen van kabels kan onherstelbare schade toebrengen aan uw computers en de OmniView™ PRO.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 63 Apparatuur installeren 3. (vervolg) Sluit uw toetsenbord en muis aan op de OmniView™ PRO. Hebt u een op AT gebaseerd toetsenbord, dan hebt u een AT-PS/2 adapter nodig (Belkin typenummer F2N017n). Achterzijde OmniView™ PRO PS/2 muis PS/2 toetsenbord 4. Verbind de VGA kabel van de eerste computer nu met de OmniView™ PRO.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 64 Apparatuur installeren 5. (vervolg) Verbind de muiskabel van de eerste computer met de OmniView™ PRO. Gebruikt u een PS/2 kabel (Belkin typenummer F2N036nXX), bevestig dan het ene kabeleinde in de PS/2 muispoort op de computer en het andere kabeleinde in de PS/2 muispoort voor PC1 aan de achterzijde van de OmniView™ PRO.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 65 Apparatuur installeren (vervolg) OPMERKING: Als een computer op de ingeschakelde poort bezig is met opstarten, raak dan de toetsen van het toetsenbord en de muis niet aan. Dit kan er oorzaak van zijn dat de computer de stuurprogramma’s van het toetsenbord en de muis niet correct herkent en initialiseert. Doorverbinden van de OmniView™ PRO: U kunt een OmniView™ PRO via de DB25-netwerkpoorten doorverbinden met extra OmniView™ PRO modules.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 66 Apparatuur installeren (vervolg) • Wanneer de doorluskabel op de vorige module aangesloten is, moet deze automatisch ingeschakeld worden als de vorige module ingeschakeld wordt. Toch is het raadzaam de voeding op de ‘slave’ module aan te sluiten. Het led display op het frontpaneel maakt de bankadresinstelling van de modules zichtbaar.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 67 Gebruik De computer die u wilt bedienen, kunt u op drie manieren benaderen: met behulp van het beeldschermmenu, met de CHANNEL toets of via sneltoetsopdrachten op het toetsenbord. Wanneer de OmniView™ PRO naar een andere computer overschakelt, is de muis een tot twee seconden lang buiten werking. Dit is een normaal verschijnsel dat zorgt dat een correcte muissynchronisatie tot stand komt.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 68 Gebruik Bank 0 (Master) Bank 1 (Slave) (vervolg) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CONSOLE Toetsenbord, muis en monitor Bank 2 (Slave) Bank F (Slave) Stand AutoScan: AutoScan activeren: In stand ‘AutoScan’ blijft de OmniView™ PRO een aantal seconden lang op een poort staan voordat hij overschakelt naar de volgende. Deze tijdinterval kan in het beeldschermmenu worden ingesteld.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 69 Gebruik (vervolg) OSD beeldschermmenu: Activeren van het beeldschermmenu Druk op [SCROLL LOCK] [SCROLL LOCK] [SPATIEBALK] om in het OSD beeldschermmenu te komen. Het OSD overlayscherm verschijnt terstond. Dit beeld wordt gegenereerd door de OmniView™ PRO en staat volledig los van uw computers of gedraaide software. • Met behulp van de pijltoetsen kunt u door de actieve poorten navigeren.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 70 Gebruik SCAN TIME (SCANTIJD): Aantal seconden dat de OmniView™ PRO op een bepaalde poort blijft staan voordat hij naar de volgende poort overschakelt. DISPLAY TIME (WEERGAVETIJD): Aantal seconden dat het Beeldschermmenu of de poortnaam op het beeldscherm zichtbaar blijft nadat een poort gekozen is.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 71 Probleemoplossing Problemen van algemene aard: V: In het beeldschermmenu staat geen ‘✹’ bij een poort waarop een ingeschakelde computer aangesloten is. Wat moet ik doen? A: • Druk tegelijk op de knoppen [BANK/SCAN] en [CHANNEL] op het frontpaneel van de OmniView™ PRO om de beginwaarden in te stellen. Ga opnieuw naar het Beeldschermmenu. Dit moet nu alle actieve poorten herkennen. V: Bij het opstarten ziet de MASTER module de ‘slave’ module resp.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 72 Probleemoplossing (vervolg) Problemen met een PS/2 muis op de console of de computers: V: Tijdens het opstarten wordt de muis niet herkend. A: • Controleer de kabels en zorg dat zij correct op de juiste poorten aangesloten zijn. • Raadpleeg de documentatie van uw computer/moederkaart en zorg dat de PS/2 muispoort (of IRQ) geactiveerd is. • Zorg dat de muis bij rechtstreekse aansluiting op de computer wordt herkend.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 73 Probleemoplossing (vervolg) V: De computers starten probleemloos maar de muis werkt niet. A: • Controleer de kabels en zorg dat zij correct op de juiste poorten aangesloten zijn. • Controleer de kabel en zorg dat dit een ongedeelde DB9 M/F (stekker/contrastekker) kabel is, bijvoorbeeld Belkin type P/N F2N209nXX-T (XX geeft de lengte in voet aan). • Raadpleeg de documentatie van uw computer/moederkaart.
P72895_F1D104nOSD-univ_man.qxd 7/16/01 3:31 PM Page 74 Informatie FCC* Verklaring *Federal Communications Commission VERKLARING VAN CONFORMITEIT MET DE FCC VOORSCHRIFTEN INZAKE ELEKTROMAGNETISCHE COMPATIBILITEIT Belkin Components verklaart onder haar uitsluitende verantwoordelijkheid dat het product: F1D104nOSD waarop deze verklaring betrekking heeft: Voldoet aan paragraaf 15 van de FCC Voorschriften.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 75 Introduzione Vi ringraziamo per aver acquistato lo switch OmniView ™ PRO KVM della Belkin Components. Gestire 4 PC da un’unica tastiera, mouse e monitor non è mai stato più facile! OmniView ™ PRO è la più recente versione di gestione.
P72895_F1D104iOSD-univ_man.
P72895_F1D104iOSD-univ_man.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 78 Elenco delle parti necessarie Accertatevi di avere i cavi giusti! OmniView ™ PRO ha bisogno dei cavi per collegare i quattro computer che vorrete gestire. Di seguito sono indicati i numeri delle parti Belkin con le relative descrizioni. Vi consigliamo di acquistare i Kit di cavi in base al tipo di porta mouse del vostro computer.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 79 Installazione hardware Bancata 0 (Master) Bancata 1 (slave) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CONSOLE Tastiera, mouse e monitor Bancata 2 (slave) Bancata 3 (slave) OmniView ™ PRO può essere collegato in catena di priorità ad altre 3 unità (per un totale di 4), consentendo all’utente di gestire fino a 16 computer! Ogni unità OmniView ™ PRO viene definita BANCATA.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 80 Installazione hardware (continua) SEGUIRE ATTENTAMENTE QUESTA PROCEDURA DI INSTALLAZIONE. IN CASO CONTRARIO SI POTREBBERO VERIFICARE ERRORI DI TASTIERA E/O MOUSE O OPERAZIONI SCORRETTE. ATTENZIONE: Prima di cercare di collegare qualsiasi unità a OmniView ™ PRO o ai computer, accertarsi che sia tutto spento. L’inserimento e l’estrazione dei cavi può causare un danno irreversibile dei computer e dell’OmniView ™ PRO.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 81 Installazione hardware 3. (continua) Collegare la tastiera ed il mouse all’OmniView ™ PRO. Nel caso di una tastiera AT, utilizzare un adattatore AT-PS/2 (pezzo Belkin n. F2N017i). Retro dell’OmniView ™ PRO Mouse PS/2 Tastiera PS/2 4. Collegare il cavo VGA del primo computer all’OmniView ™ PRO. Utilizzando un cavo VGA (pezzo Belkin n.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 82 Installazione hardware 5. (continua) Collegare il mouse del primo computer all’OmniView ™ PRO. Se si utilizza un cavo PS/2 (pezzo Belkin n. F2N036iXX) collegare un’estremità della porta del mouse PS/2 al computer e l’altra alla porta del mouse PC1 PS/2 sul retro dell’OmniView ™ PRO. Se si utilizza un mouse seriale (pezzo Belkin n.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 83 Installazione hardware (continua) NOTA: Evitare di premere qualsiasi bottone della tastiera o di muovere il mouse se la porta selezione ha un computer in fase di caricamento. In caso contrario il computer potrebbe non rilevare o caricare i driver della tastiera o del mouse correttamente.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 84 Installazione hardware (continua) • RESETTARE l’unità MASTER premendo i pulsanti BANCATA / SCANSIONE e CANALE contemporaneamente o attivando il comando [BLOC SCORR], [BLOC SCORR], [FINE]. Questo è necessario perché l’unità MASTER rilevi l’unità slave aggiunta. • Accertatevi che l’unità MASTER abbia rilevato il nuovo slave premendo il pulsante BANCATA / SCANSIONE.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 85 Impiego La selezione del computer da utilizzare può essere effettuata o dall’On-Screen Display, dal pulsante CHANNEL, o dai comandi della tastiera. Si potrà notare che una volta che OmniView ™ PRO passa ad un altro computer, il mouse diviene inoperativo per circa 1-2 secondi. Si tratta di un’operazione normale che garantisce che venga stabilita una giusta sincronizzazione con il mouse.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 86 Impiego Bancata 0 (Master) Bancata 1 (slave) (continua) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CONSOLE Tastiera, mouse e monitor Bancata 2 (slave) Bancata 3 (slave) Modalità AutoScan: Attivare la modalità AutoScan In modalità AutoScan l’OmniView ™ PRO rimane su una porta per alcuni secondi prima di passare alla successiva. Questo intervallo viene impostato sul menu On-Screen Display.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 87 Impiego (continua) Gestione del menu On-screen Display: Attivare il menu On-screen Display Per entrare nel menu On-screen Display (OSD), premere [BLOC SCOR] [BLOC SCOR] [SPAZIO]. Compare immediatamente la videata OSD. Questa videata viene generata dall’OmniView ™ PRO e non influenza in nessun modo i computer o il software utilizzato. • E’ possibile navigare attraverso le porte attive con i tasti direzionali.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 88 Impiego INTERVALLO DI SCANSIONE: Corrisponde all’intervallo di tempo durante il quale OmniView ™ PRO rimane su una porta prima di passare alla successiva in modalità di scansione. INTERVALLO DI VISUALIZZAZIONE: Indica l’intervallo di tempo durante il quale il menu OSD o il Nome Porta rimane visualizzato dopo aver selezionato la porta.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 89 Risoluzione degli errori Problemi generali: D: Il menu OSD non visualizza il "✹" su di una porta alla quale il computer è collegato ed alimentato. Cosa fare? R: • Resettare l’OmniView ™ PRO premendo contemporaneamente i tasti BANCATA / SCANSIONE e CANALE sul pannello frontale. Entrare nel menu OSD di nuovo, esso dovrebbe avere rilevato nuovamente le porte attive. D: Nel caso di collegamento in cascata, l’unità MASTER non rileva le unità slave.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 90 Risoluzione degli errori (continua) D: I computer caricano bene il sistema operativo, ma la tastiera non funziona. R: • Controllare i cavi ed accertarsi che siano inseriti correttamente nelle porte giuste. • Accertarsi che la tastiera funzioni quando inserita direttamente nei computer. • Provare una tastiera diversa, ma usare solo tastiere a 101, 102 o 104 tasti.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 91 Risoluzione degli errori (continua) D: Nel passare da una porta all’altra il movimento del mouse è completamente erratico. Cosa devo fare? R: • RESETTARE l’OmniView ™ PRO premendo contemporaneamente i pulsanti BANCATA / SCANSIONE e CANALE sul pannello frontale o utilizzare i tasti di comando [BLOC SCOR] [BLOC SCOR] [FINE] per resettare l’OmniView ™ PRO. Accedere nuovamente al menu OSD, dovrebbe aver rilevato di nuovo le porte attive.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 92 Risoluzione degli errori (continua) D: Quando passo da una porta all’altra il movimento del mouse è completamente erratico. Cosa devo fare? R: • RESETTARE l’OmniView ™ PRO premendo contemporaneamente i pulsanti BANCATA / SCANSIONE e CANALE sul pannello frontale. Accedere di nuovo al menu OSD che dovrebbe aver di nuovo rilevato le porte attive. • Accertarsi che non siano caricati più di un driver per mouse seriale.
P72895_F1D104iOSD-univ_man.qxd 7/16/01 6:37 PM Page 93 Information Informazioni Dichiarazione FCC DICHIARAZIONE DI CONFORMITÀ CON LE NORME FCC PER LA COMPATIBILITÀ ELETTROMAGNETICA Noi sottoscritti, Belkin Components, di 501 West Walnut Street, Compton CA 90220, dichiariamo sotto la nostra piena responsabilità che il prodotto: F1D104iOSD to which this declaration relates: È conforme all’art.15 delle Norme FCC.